Use and Care Manual
Fasteners
23
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Fasteners
MiTek
®
Product Catalog
N / NA Nails
Finish
3,7
Size Ref. No. Length
3 7 10 12 14 16 18 20 22
8d x 1-1/2 NA11 N8 0.131 1-1/2 152 -- -- -- -- -- 96 95 94 94 32
10d x 1-1/2 NA9D N10 0.148 1-1/2 100 -- -- 139 127 119 116 114 114 113 36
10d Common N10C 10DHDG 0.148 3 70 -- 158 139 127 119 116 114 114 113 36
16d x 2-1/2 NA16D N16, N16EG 0.162 2-1/2 66 194 181 161 149 141 138 137 136 -- 40
16d Common N16C 16DHDG 0.162 3-1/2 48 194 181 161 149 141 138 137 136 -- 40
20d x 2-1/2 NA20D -- 0.192 2-1/2 41 234 207 187 175 168 -- -- -- -- 47
8d x 1-1/2 N8-GC -- 0.131 1-1/2 152 -- -- -- -- -- 96 95 94 94 32
10d x 1-1/2 N10-GC -- 0.148 1-1/2 118 -- -- 139 127 119 116 114 114 113 36
10d Common N10C-GC -- 0.148 3 70 -- 158 139 127 119 116 114 114 113 36
16d Common N16C-GC -- 0.162 3-1/2 48 194 181 161 149 141 138 137 136 -- 40
8d x 1-1/2 SSNA8D SSN8 0.131 1-1/2 147 -- -- -- -- -- 96 95 94 94 32
10d x 1-1/2 SSNA10D SSN10 0.148 1-1/2 126 -- -- 139 127 119 116 114 114 113 24
8d Common SSN8C SS8D 0.131 2-1/2 94 -- -- -- -- 99 96 95 94 94 22
10d Common SSN10C SS10D 0.148 3 67 -- 158 139 127 119 116 114 114 113 24
16d Common SSN16C SS16D 0.162 3-1/2 44 194 181 161 149 141 138 137 136 136 27
8d Common 8d Common -- 0.131 2-1/2 126 -- -- -- -- 99 96 95 94 94 32
10d Common 10d Common -- 0.148 3 70 -- 158 139 127 119 116 114 114 113 36
16d Sinker 16d Sinker -- 0.148 3-1/4 60 162 158 139 127 119 116 114 114 -- 36
16d Ring Shank NA16D-RS -- 0.148 3-1/2 57 183 168 150 -- -- -- -- -- -- 36
16d Common 16d Common -- 0.162 3-1/2 48 194 181 161 149 141 138 137 136 -- 40
20d Common 20d Common -- 0.192 4 29 234 207 187 175 168 -- -- -- -- 47
1
)
Loads are calculated to s
p
ecifications of Part 12 of the National Desi
g
n S
p
ecifications for Wood Construction
(
NDS®
)
, 2018 Edition.
2
)
Loads a
pp
l
y
to Dou
g
las Fir
(
G=0.50
)
and Southern Pine
(
G=0.55
)
. For S
p
ruce-Pine-Fir
(
G=0.42
)
multi
p
l
y
above values b
y
0.86. For
other wood t
yp
es refer to NDS or consult MiTek.
3
)
HDG = Hot-Di
p
Galvanized; SS = Stainless Steel; GC = Gold Coat; Bri
g
ht = No Finish.
4
)
For 3
g
au
g
e steel with Fu=58,000
p
si and 7
g
au
g
e thru 22
g
au
g
e steel with Fu=45,000
p
si. Shear values assumes full
p
enetration
of at least 10 nail diameters.
5
)
Fastener values ma
y
be increased for duration of load.
6
)
Withdrawal loads are in
p
ounds
(
lbs
)
p
er linear inch of embedment into main member.
7
)
Bri
g
ht finish common and sinker nails are listed in table for reference onl
y
. MiTek does not stock these t
yp
e nails.
8) Stainless steel 8d x 1-1/2 nails are ring shank. Other stainless steel nail sizes in table are smooth shank, and withdrawal values
are in accordance with Table 12.2D of the 2018 NDS.
Corrosion
Finish
HDG
SS
8
GC
Bright
MiTek USP
Stock No.
7
Nail
Diameter
Withdrawal
Load
(Lbs/in)
6
Dimensions (in)
DF/SP Allowable Shear per Nail (Lbs.)
1,2,4,5
Steel Gauge
Nails
Per Lb.
Nail Specication Table
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
6d 11-1/2 .113 1.13 0.68
8d 10-1/4 .131 1.31 0.79
10d 9 .148 1.48 0.89
12d 9 .148 1.48 0.89
16d Sinker 9 .148 1.48 0.89
16d 8 .162 1.62 0.97
20d 6 .192 1.92 1.15
1) For penetration less than this distance, the nail has no value.
2) Penetrations are derived according to the 2018 NDS.
Minimum
Penetration for
Reduced Shear Load
1
(in)
Minimum
Penetration for
Full Shear Load
(in)
Nail
Penny
Wire
Gauge
Shank
Diameter
(in)
Reduced Fastener Penetration Example
(See chart above):
HD210 (Min) – listed load is 1540 lbs. @ 100% for 16d common nails.
Reduced HD210 capacity if using a 2x DF-L or SP header:
1540 lbs. x 1.5
= 1425 lbs. @ 100%
1.62
!
Minimum Fastener Penetration Table