Use and Care Manual
234
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Glulam Beam Connectors
Glulam Beam Connectors
MiTek
®
Product Catalog
GHF Glulam Face Mount Hangers
Specialty Options Chart
– refer to Specialty Options pages 320-321 for additional details
Option
Skewed
1,3
Sloped Seat
2
Sloped / Skewed
1,2
Inverted Flange
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) Skewed hangers typically require a bevel cut however, a square cut option may be available as a custom when requested.
Allowable
Loads
Ordering
80% of table load
75% of uplift load on skews
greater than 15˚.
100% of table load.
65% of table load when
fastening into the
support members
end grain.
Add
SK
, angle required,
right
(R)
or left
(L)
, and
square cut
(SQ)
or
bevel cut
(BV)
to product number.
Ex. GHF31900_SK45R_BV
See Sloped Seat and Skewed.
Ex.
GHF31900_SK45R_BV_SL30D
Add
IF
to product number.
Ex. GHF51135_IF
Add
SL,
slope required, and
up
(U)
or down
(D),
to product number.
Ex. GHF31900_SL30D
100% of table load
100% of table load.
75% of uplift load on skews
greater than 15˚.
Range
1˚ to 50˚ 1˚ to 45˚ See Sloped Seat and Skewed
Not available in widths
less than 4-1/2"
Typical GHF51135IF
inverted ange
installation
KEGQ Glulam Beam Hangers
MiTek’s WS structural wood screw fastening, heavy steel
construction, and a continuous top ange allow the KEGQ
products to have high load capacities.
Materials: See chart
Finish: Primer
Codes: IBC, FL, LA
Installation:
• Install with MiTek’s WS structural wood screws.
• MiTek’s WS3 structural wood screws, 1/4" dia. x 3" long,
are supplied with KEGQ hangers.
• Minimum header height (H) is 11-7/8".
• Beam height dimension (H) must be specied when ordering.
Uplift
1
Uplift
1
Ref. No W
H
2
D
L
Qty
Type
Qty
Type
100%
115%
125%
160%
100%
115%
125%
160%
3-1/2
KEGQ362
EGQ3.62-SDS3 3 7
3-5/8
specify 6 18 28 WS3 12 WS3
17265 17265 17265 4695
13005 13615 13795 3750
5-1/4 KEGQ550 EGQ5.25-SDS3 3 7 5-1/2 specify 6 18 28 WS3 12 WS3
17265 17265 17265
7430 13720 13720 13720 6525
7 KEGQ725 EGQ7.25-SDS3 3 7 7-1/4 specify 6 18 28 WS3 12 WS3
17265 17265 17265
7430 13680 13680 13680 6525
1) Uplift loads have been increased 60% for wind and seismic loads; no further increase shall be permitted.
2) "Specify" denotes the required supported beam height that must be specified at the time of ordering, with 11" being the minimum.
3) MiTek's WS3 structural wood screws are 1/4" dia. x 3" long and are included with KEGQ hangers.
New products or updated product information are designated in
blue font
.
Joist /
Purlin
Size
IBC,
FL,
LA
Dimensions (in)Steel Ga.
Top Flange
Code
Ref.
U-Strap
S-P-F
Allowable Loads (Lbs.)
Download
DF/SP
Allowable Loads (Lbs.)
Download
Fastener
Schedule
3
Header Joist
MiTek USP
Stock No.
Typical KEGQ550
installation
KEGQ
D
W
L
11-3/4"
H