Use and Care Manual

320
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Specialty Options
Specialty Options
MiTek
®
Product Catalog
The information listed only applies to hangers
manufactured by MiTek
®
and installed according to
the instructions listed in this catalog. Some of the
options listed may not have been evaluated on a
single hanger. The designer must always evaluate
each connection, including the joist and header
capacities, before specifying a specialty connector.
MiTek sloped hangers are manufactured with the
plumb cut of the joist already calculated. If a hanger
with a different height is needed, it must be specied
at the time of ordering.
Materials: Steel gauge may vary from that specied
depending on the specialty option and manufacturing
process used. Some formed hangers may be welded
when modifying the hanger. Hanger congurations,
fastener schedules, and height may vary from the
tables depending on the joist size, skew, and slope.
Finish: See specic hanger option tables.
Welded hangers are painted with gray primer.
Non-catalog hangers available in Hot-dip
galvanized, use HDG after product number.
Allowable Loads: For multiple options for the same
connector, use the most conservative reduction to give
the lowest design load. See specic hanger option
tables for applicable load reductions and maximum
tolerances. Reference Specialty Options Summary
Table for MiTek series catalog page references.
Installation:
• Fill all nail holes with fasteners specied in
the tables.
• Fastener quantities may increase from the amount
listed in the tables depending on hanger option.
• NA16D-RS and NA20D nails are supplied
with hangers.
• For bevel cut skewed hangers, the end of joist must
be bevel cut; for square cut skewed hangers,the end
of joist must be square cut.
Codes: Modied hangers are not code
evaluated due to their numerous variations.
MiTek
USP
Series
Width
Skewed (Maximum)
Sloped Seat
(Maximum)
Sloped / Skewed
Sloped Top Flange
(Maximum)
Top Flange Offset Saddle Hanger
Ridge Hanger
(Maximum)
Inverted Flange Uplift Weldability
MiTek Series
Catalog Page
Reference
BPH all 50º 45º • 45º • • 218
FWH all 70º • • 194
FWH/S
all 70º • • 337
FWHBP
all 70º • 196
FWHFM
all 70º • 200
FWHH
all 70º • 198
GHF all 50º 45º •
•
width > 4-1/2"
• 233
HBPH all 50º 45º • 45º • • 218
1-3/4" or less 67-1/2º
> 1-3/4" 50º
1-3/4" or less 67-1/2º
> 1-3/4" 50º
HGU all 45º
• one flange
width > 5-1/4"
• 232
HGUM all • one flange 187
HJC all 60º • 281
HLBH all 50º 45º • 45º • • 45º • 219
HUS all
•
width > 2-1/4"
• 140
HWUH all 45º 45º • • • • 190
1-3/4" or less 67-1/2º
> 1-3/4" 50º
KB all • • 166
KEG all 45º 45º • 235
KGB all • • 236
KGH all 45º • 63
KGLS all 50º 45º • 30º • • • • 238
KGLST all • • • 238
KGLT all 50º 45º • 45º • • • • 237
KHGB all • • 236
KHGLS all 50º 45º 30º • • • • 238
KHGLST all • • • 238
KHGLT all 50º 45º • 45º • • • • 237
KHHB all • • 236
KHW all 84º 45º • 35º • • 45º • 168
KLB all • 166
KLEG all 45º 45º • • 235
KMEG all 45º 45º • • 235
LGU all 45º
• one flange
width > 3-5/8"
• 232
LGUM all • one flange 187
LSSH all 45º 45º • • 174
MGU all 45º
• one flange
width > 5-1/4"
• 232
MPH
1
all 60º 45º • • 188
MSHA all 75° • 278
MSHL/R all 45º • 276
NFM all 45º • 192
PHM all 84º 45º • 35º • • 45º • 220
PHXU
1
all 60º 45º • 35º • • • • 220
SKH/SKHH all 45º • 175
1-3/4" or less 67-1/2º
> 1-3/4" 50º
SW
1
/SWH
1
all 84º 45º • 35º • • 45º • 168
THDH all 45º 45º • • 270
1) Skews greater than 45° will have square cut joist with back plate.
Refer to Typical HLBH hanger skewed, left shown, square cut illustration on page 322.
2) HD hanger widths less than 2-1/4" may have flanges inverted as a Custom, contact MiTek.
New products or updated product information are designated in
blue font
.
•
•
width > 2-1/4"
> 1-3/4" 50º
208
167
THF
45º 45º •
45º •
THD all
• one flange
width > 3"
•
•
•
45º
45º
SUH 45º
HD
1,2
HDO
IHFL/IHF
45º
•
width > 2-1/4"
••
•
207
269
139
•
width > 3-1/8"
•
•
•
width > 2-1/4"
• 206
Specialty Options & General Notes
Specialty Options Summary Table