Use and Care Manual

63
Concrete & Masonry
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Concrete & Masonry
MiTek
®
Product Catalog
KGH Floor Girder Hangers
Connects girder beams to foundation walls and eliminates the
need to block out pockets or inserts while forming foundation.
Materials: 12 gauge
Finish: Primer
Options: See Specialty Options Chart. Consult MiTek for
non-catalog design variations
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• H dimension assumes 2x mudsill. For 3x or larger mudsill,
please contact factory.
• The 1-1⁄2" hole, centered in the saddle, allows for installation
over any protruding foundation bolts. This is not required.
• Placement of a wood sill over the top of the KGH top ange
is required to achieve allowable loads.
Specialty Options Chart –
refer to Specialty Options pages 320 and 322-323 for additional details.
Dimensions (in)
Ref. No. W L D S H Qty Type 100% 125% 100% 125%
4 x 6 KGH46-6 GH46-6 12 6
4 x 6 KGH46-8 GH46-8 12 8
4 x 8 KGH48-6 GH48-6 12 6
4 x 8 KGH48-8 GH48-8 12 8
6 x 6 KGH66-6 GH66-6 12 6
6 x 6 KGH66-8 GH66-8 12 8
6 x 8 KGH68-6 GH68-6 12 6
6 x 8 KGH68-8 GH68-8 12 8
1)
NAILS:
16d nails are 0.162" dia. x 3-1/2" long.
New products or updated product information are designated in
blue font
.
2200
3070 3070
3070 3070
2200
4 4 16d
6 4 16d
5-1/2 6-1/4
6-1/45-1/2
3
3
5 3 4 16d6
Code
Ref.
IBC,
FL,
LA
Fastener
Schedule
1
Girder
Size
MiTek USP
Stock No.
Steel
Gauge
DF/SP Allowable
Loads (Lbs.)
3-9/16 5 3-1/4 4 4 16d
2200 2200
3-9/16
2410 2410
2410 2410
S-P-F Allowable
Loads (Lbs.)
1725 1725
1725 1725
Option
Skewed
1,2
Saddle
Range 1˚ to 45˚ --
1
)
Skewed han
g
ers with skews
g
reater than 15° ma
y
have all
j
oist nailin
g
on outside flan
g
e.
2
)
For skewed han
g
ers, the re
q
uired cut t
yp
e
(
s
q
uare or bevel
)
of
j
oist
member ma
y
var
y
based on skew an
g
le and width of han
g
er. Some
s
q
uare cut han
g
ers will re
q
uire custom
p
ricin
g
due to welded back
p
late.
Allowable
Loads
Ordering
100% of table load.
100% of table load
per side.
Add SA, and saddle
width required
to product number.
Ex. KGH46-6_SA=5-1/2"
Add
SK , angle required,
right (
R ) or left ( L ), and
square cut (
SQ ) or bevel cut ( BV )
to product number.
Ex. KGH46-6_SK45R_BV
Typical KGH installation
KGH
S
1"
H
L
W D
KGH saddle
Specialty Option