Use and Care Manual
70
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Holdowns
Holdowns
MiTek
®
Product Catalog
HTT Tension Ties
Secures multi-ply studs or posts to mudsills or foundation. Nail
fastening makes for a convenient connection to studs or posts in
cramped retrot installations.
Materials: See chart
Finish: G90 galvanizing
Codes: See chart for code references
Installation:
• Use all specied fasteners to attach the strap portion of the
connector to the side of stud, post, joist, purlin, or beam. Secure
the base to the concrete or masonry wall with specied anchor
bolt. A design professional shall specify the type, length, and
embedment of the anchor bolt.
• HTT45 Max – Fill all round and diamond nail holes.
• Washers are not required on transfer plates that t over the
anchor bolt.
• Tighten anchor bolt nuts nger tight to base plus 1/3 to 1/2
additional turns with a wrench.
• LL930 (#9 X 2-7/8" long) LumberLok Screws are included
with HTT45KT.
HTT16
HTT45
Typical HTT45
max installation
Typical HTT16
installation
Ref. No. W L D CL Qty Dia. Qty Type 160% Δ (in)
4,5
HTT16 HTT4 10 2-1/2 16 2 1-3/8 1-3/4 -- 1 5/8 18 10d 3610 0.142
10d 4215 0.115
16d x 2-1/2 4160 0.108
10d 5795
16d x 2-1/2 5005
HTT45KT
6
HTT5KT 10 2-1/2 16 2 1-3/8 1-3/4 -- 1 5/8 26 LL930 5865 0.113 --
1
)
Allowable loads have been increased 60% for wind or seismic loads; no further increase shall be
p
ermitted.
2
)
16d sinkers ma
y
be substituted for the s
p
ecified 10d common nails with no load reduction.
16d common nails ma
y
be substituted for the s
p
ecified 16d x 2-1/2" nails with no load reduction.
3
)
The desi
g
ner must s
p
ecif
y
anchor bolt t
yp
e, len
g
th and embedment de
p
th.
4
)
Deflections are derived from static, monotonic load tests of devices connected to DF wood members with s
p
ecified fasteners.
5
)
HTT holdowns raised off of the sill
p
late ma
y
have hi
g
her deflection values.
6
)
HTT45KT is sold as a kit and includes
(
1
)
HTT45 and
(
26
)
LL930 screws.
7
)
NAILS: 10d nails are 0.148" dia. x 3" lon
g
, 16d x 2-1/2" nails are 0.162" dia. x 2-1/2" lon
g
.
Min
HTT45
1 5/8
1 5/8
HTT4,
HTT5
1-3/42-1/2 16 2
Max 0.101
Steel
Gauge
Dimensions (in)
MiTek USP
Stock No.
Code
Ref.
1-3/810
Nail
Spacing
IBC,
FL,
LA
Anchor
Bolt
3
Strap
2,3,7
18
26
DF/SP
Allowable Tension
Loads (Lbs.)
1
Fastener Schedule
Min/
Max
W
L
D
CL
W
L
Standard round
nail holes for
minimum nailing
Additional
diamond holes
for maximum
nailing
D
CL