Use and Care Manual

109
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Angles & Straps
Angles & Straps
MiTek
®
Product Catalog
A / AC / JA / MP Framing Angles
Ref. No. W1 W2 L Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
F1 480 545 590 740 410 470 510 520
F2 480 545 590
605
410 470 485
505
F3 375 375 375 375 145 165 180 230
MP3 LS30 18 2-1/4 2-1/4 3-3/8 3 10d 3 10d F1
360 410 445 455 310 350 380 380
MP5 LS50 18 2-1/4 2-1/4 4-5/8 4 10d 4 10d F1
480 545 590 740 410 470 505 640
MP7 LS70 18 2-1/4 2-1/4 5-7/8 5 10d 5 10d F1
600 685 740 930 515 585 630 800
MP9 LS90 18 2-1/4 2-1/4 6-7/8 6 10d 6 10d F1
720 820 885 1115 620 705 760 960
F1 375 420 455 565 310 360 390 500
F2 375 420 455 565 310 360 390 500
F3 155 180 195 250 215 250 270 345
F1 440 500 540 670 370 425 460 545
F2 440 500 540 595 370 425 460 590
F3 175 205 220 280 280 320 345 445
F1 500 560 605 755 415 480 520 665
F2 500 560 605 755 415 480 520 665
F3 210 240 260 335 290 330 360 460
F1 590 665 720 895 495 565 615 770
F2 590 665 720 895 495 565 615 790
F3 235 270 295 375 370 425 465 590
F1 625 700 755 945 520 595 650 830
F2 625 700 755 900 520 595 650 830
F3 260 300 325 415 360 415 450 580
F1 735 835 900 1120 615 710 770 985
F2 735 835 900 900 615 710 770 920
F3 295 340 370 470 465 530 580 740
F1 220 220 220 220 195 195 195 195
F2 -- -- -- 300 -- -- -- 235
F3 -- -- -- 150 -- -- -- 100
F1 495 495 495 495 445 445 445 445
F2 -- -- -- 465 -- -- -- 365
F3 -- -- -- 330 -- -- -- 225
F1 790 825 825 825 715 740 740 740
F2 -- -- -- 890 -- -- -- 695
F3 -- -- -- 495 -- -- -- 335
F1 1055 1185 1270 1560 955 1070 1145 1410
F2 -- -- -- 1450 -- -- -- 1135
F3 -- -- -- 490 -- -- -- 335
F1 1320 1485 1590 1950 1190 1340 1430 1760
F2 -- -- -- 1465 -- -- -- 1150
F3 -- -- -- 775 -- -- -- 530
1) Allowable loads have been increased 60% for wind and seismic loads; no further increase shall be permitted.
2) Loads are shown per angle, and may be doubled if installed in pairs. When using a single angle, joist must be constrained from rotation.
3) Stainless steel ring shank nails must be used with stainless steel connectors to achieve tabulated allowable loads.
4)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
New products or updated product information are designated in
blue font
.
Fastener Schedule
3,4
10d x 1-1/2
7
Header
Direction
of Load
2-1/2 2-1/2
62-1/2 2-1/2 5 16d
3
1-5/16 2-3/8
16d
10d x 1-1/2
16d 4
2-3/4 4
10d x 1-1/2
10d x 1-1/2
10d x 1-1/2
Steel
Gauge
4
Code
Ref.
10d
1-1/2
MiTek USP
Stock No.
3
4-7/8
10d
16d
AC5 L50 16
AC9 L90 16 1-5/16
AC7 L70 16 1-5/16
16d
10d
Joist
JA1 A21 16 1-1/4 2
JA5 -- 14
JA3 -- 14
A3
A23, GA1,
GA2, L30
18 1-7/16 1-7/16
10d
16d
10d x 1-1/2
10d
16d
4
JA9 -- 14 9 10
JA7 -- 14 2-1/2 8
102-1/2 2-1/2
16d 8
16d
2
4
1-1/2
6
10d x 1-1/2
10d x 1-1/2
Dimensions (in)
DF/SP
Allowable Loads (Lbs.)
1,2
S-P-F
Allowable Loads (Lbs.)
1,2
IBC,
FL,
LA
Corrosion
Finish
2-1/2
33
3
2-3/8 8-7/8
55
55
2-3/8 6-15/16
4
44
10d
16d
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• MP Framing Angles are fabricated at 100° and may be eld adjusted by hand from 45° to 180° (at). Bend angle only once.