Use and Care Manual

168
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Lumber Hangers
Lumber Hangers
MiTek
®
Product Catalog
KHW / SW / SWH Welded Top Flange Hangers
SW – Light-duty hanger
SWH – Medium-duty hanger
KHW – Heavy-duty hanger installs with NA20D nails for
higher load capacities
Materials: SW top ange - 12 gauge; stirrup - 12 gauge;
SWH top ange - 7 gauge; stirrup - 12 gauge;
KHW top ange - 3 gauge; stirrup - 10 gauge
Finish: Primer
Options: All nominal lumber sizes are available for rough/
full size lumber. See Specialty Options below.
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• NA20D nails are supplied with KHW hangers.
• For welded installations see page 325.
• KHW models are not recommended for use with
LVL, PSL, or LSL headers.
Typical SW210 installation
Typical KHW46 installation
SW210
KHW46
SWH410
Nailer Installation Chart
Chart represents maximum allowable loads for hangers used on wood nailers. Reference page 203.
Specialty Options Chart – Refer to Specialty Options pages 320, 322-323 for additional details.
Type
Qty
Type
2X 2 10d x 1-1/2 2 10d x 1-1/2 1635 1115
3x 2 16d x 2-1/2 2 10d x 1-1/2 2390 2010
(2) 2x 2 16d x 2-1/2 2 10d x 1-1/2 2390 2010
4x 2 16d x 2-1/2 2 10d x 1-1/2 2390 2010
2X 2 10d x 1-1/2 2 10d x 1-1/2 2600 1770
3X 2 16d x 2-1/2 2 10d x 1-1/2
3305
2280
(2) 2x 2 16d x 2-1/2 2 10d x 1-1/2
3305 2280
4x 2 16d x 2-1/2 2 10d x 1-1/2
3305 2280
KHW 3X 4 16d x 2-1/2 2 10d
4415
3525
1) Listed loads shall not be increased.
2)
SW hangers with a width of less than 2-9/16" are limited to 2,315 lbs. of download.
3)
Values in the table apply to standard top mount hangers without slope, skew or any other specialty options.
4)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long,
16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
New products or updated product information are designated in
blue font
.
SWH
MiTek
Series
Nailer
Size
DF/SP
Allowable Loads (Lbs.)
1,3
SPF
Allowable Loads (Lbs.)
1,3
Fastener Schedule
4
Nailer Joist
SW
2
widths ≥ 2-9/16"
Top
Qty
Download
100%
Download
100%
Option
Skewed
1,3
Sloped Seat
2
Sloped / Skewed
1,2,3
Sloped Top Flange
4
Saddle Ridge
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) For skewed hangers, the required cut type (square or bevel) of joist member may vary based on skew angle
and width of hanger. Some square cut hangers will require custom pricing due to welded back plate.
4) Sloped top flanges with greater than 15° may have additional header nails.
Range
Allowable
Loads
Ordering
1˚ to 84˚
100% of table load
See Sloped Seat
and Skewed
Add
SK, angle required,
right (
R ) or left ( L ), and
square cut (
SQ ) or
bevel cut (
BV )
to product number.
Ex. SW212_SK45R_SQ
Add
SL, slope required,
and up
(U) or down (D),
to product number.
Ex. SW212_SL30D
See Sloped Seat
and Skewed.
Ex.
SW212_SK45R_SQ_SL30D
Add
SF, angle required,
and right
(R) or left (L),
to product number.
Ex. SW212_SF30L
100% of table load 100% of table load 100% of table load
1˚ to 45˚ 0° to 35°
Add
DA,
angle required
to product number.
Ex. SW212_DA30
Top Flange Offset
Add
OS, and
right
(R) or left (L),
to product number.
Ex. SW212_OSL
% of
table load:
60%
75%
85%
100% of table load
per side
Hanger Width
3-1/2" or less
3-9/16" to 5-1/2"
5-9/16" to 7-1/2"
100% of table load
0° to 45°----
Add
SA, and saddle
width required
to product number.
Ex. SW212_SA=5-1/2"
D
H
2-1/2"
L
W
D
H
W
L
TF
D
TF
L
H
W