Use and Care Manual

Lumber Hangers
175
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Lumber Hangers
MiTek
®
Product Catalog
SKH / SKHH Skewed 45° Hangers
SKH26R
right skew
SKH26L
left skew
SKH – Standard 45° skew hanger allows for a
40° to 50° skew range, without hanger modication
SKHH – For heavier applications
Materials: 14 or 16 gauge
Finish: G90 galvanizing
Options: See chart for Corrosion Finish Options
Codes: See chart for code references
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• The hangers listed are for standard sizes and will accommodate
a 40° to 50° skew range.
• Most sizes do not require a miter cut for installation. Refer to chart
footnote identied with an asterisk.
• Illustrations show left and right skews. (SKH_L = skewed left;
SKH_R = skewed right)
• For I-Joist installations, web stiffeners are required.
• Refer to illustration for staggered I-Joist application for double 2",
2-5/16", and 2-1/2" models.
• For double I-Joist installations, web stiffeners between
I-Joists are required.
SKH210LSKH210R
Left skew
Right skew
Drive nails at angle
W
H
D
W
D
H
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
SKHH210L-2
left skew
SKHH210L
left skew
W
H
W
D
D
W
Floor
Uplift
1
Floor
Uplift
1
Ref. No. W H D Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
2 x 4 SKH24L/R SUR/L24 16 1-9/16 3-1/4 1-7/8 4 16d 4 10d x 1-1/2 510 510 510 545 395 395 395 425
SKH26L/R SUR/L26 16 1-9/16 5-1/4 1-7/8 6 16d 6 10d x 1-1/2 840 890 890 1135 700 700 700 980
SKHH26L/R -- 16 1-5/8 5-1/8 3-1/4 18 16d 12 10d x 1-1/2 1765 1795 1795 795 1450 1450 1450 645 --
SKH28L/R -- 16 1-9/16 7-1/4 1-7/8 10 16d 8 10d x 1-1/2 1400 1465 1465 1350 1160 1160 1160 1070 IBC, FL, LA
SKHH28L/R -- 16 1-5/8 7 3-1/4 26 16d 16 10d x 1-1/2 2350 2525 2525 1155 2055 2055 2055 940 --
SKH210L/R
SUR/L210,
SUR/L214
16 1-9/16 9-1/4 1-7/8 14 16d 10 10d x 1-1/2 1790 1790 1790 1530 1425 1425 1425 1220
IBC,
FL, LA
SKHH210L/R -- 16 1-5/8 9 4-1/4 34 16d 20 10d x 1-1/2 2625 2625 2625 1420 2150 2150 2150 1160 --
1-3/4 x
11-1/4 - 18
SKH1724L/R
SUR/L1.81/11,
SUR/L1.81/14
16 1-13/16 11-1/8 1-7/8 16 10d 10 10d x 1-1/2 1890 2170 2360 1530 1635 1880 2035 1220
2 - 2-1/8 x
9-1/4 - 14
SKH2020L/R
SUR/L2.06/9,
SUR/L2.1/9
16 2-1/8 9 1-7/8 14 10d 10 10d x 1-1/2 1650 1760 1760 1530 1390 1390 1390 1210
2 - 2-1/8 x
11-1/4 - 18
SKH2024L/R
SUR/L2.06/11,
SUR/L2.1/11
16 2-1/8 11 1-7/8 16 10d 10 10d x 1-1/2 1890 2170 2360 1530 1635 1880 2020 1210
2-1/4 - 2-5/16 x
11-1/4 - 18
SKH2324L/R
SUR/L2.37/11,
SUR/L2.37/14
16 2-3/8 10-7/8 1-7/8 16 10d 10 10d x 1-1/2 1890 2170 2360 1530 1635 1880 2020 1210
1
)
U
p
lift loads have been increased 60% for wind and seismic loads; no further increase shall be
p
ermitted.
2
)
NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" lon
g
, 16d nails are 0.162" dia. x 3-1/2" lon
g
.
*Miter cut re
q
uired on end of
j
oist to achieve desi
g
n loads.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
Beam/Joist
Size
2 x 6-8
2 x 8-12
Code
Ref.
Roof
IBC,
FL, LA
DF/SP
Allowable Loads (Lbs.)
S-P-F
Allowable Loads (Lbs.)
MiTek USP
Stock No.
Corrosion Finish
Dimensions (in)
Ga.
Fastener Schedule
2
Roof
Header Joist
2 x 10-14
1-3/4 x
9-1/4 - 14
2-1/4 - 2-5/16 x
9-1/4 - 14
SKH1720L/R SUR/L1.81/9
SKH2320L/R SUR/L2.37/9
16
16 2-3/8 8-7/8
1-13/16 9-1/8
IBC,
FL,
LA
14 10d 10 10d x 1-1/2 1650 1760 1760 1530 1390 1390
122014 10d 10
1390 1210
17601-7/8
1-7/8
1400 140010d x 1-1/2 1650 1530 14001760
Typical SKH26L
installation
left skew
Continued on next page