Use and Care Manual

EWP Hangers
219
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
HLBH Beam Hangers
Heavy-duty hanger for LVL, LSL, and PSL beams.
Materials: 7 gauge
Finish: Primer
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• For welded installations, see page 325.
• 16d ring shank nails are supplied with HLBH hangers.
Typical HLBH
installation
HLBH
Fastener Schedule
4
Type Qty Type
2x 3 4 10d x 1-1/2 6 10d x 1-1/2 6115 -- 5135 --
3x 3 6 16d x 2-1/2 6 10d 6825 -- 5735 --
(2) 2x 3 8 10d 6 10d x 1-1/2 4385 -- 3685 --
4X 3 8 NA16D-RS 6 10d x 1-1/2 9600 1115 6900 935
4X 3 8 NA16D-RS 6 16d 9600 1115 6900 935
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) Listed loads shall not be increased.
3)
Values in the table apply to standard top mount hangers without slope, skew or any other specialty options.
4)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long,
NA16D-RS nails are 0.148 dia, x 3-1/2" long, 16d nails are 0.162" dia. x 3-1/2" long.
New products or updated product information are designated in blue font.
DF/SP
Allowable Loads (Lbs.)
2,3
SPF
Allowable Loads (Lbs.)
2,3
Nailer Joist
HLBH
Nailer
Size
Uplift
1
160%
Uplift
1
160%
MiTek
Series
Top
Qty
Face
Qty
Download
100%
Download
100%
Option
Skewed
1,3
Sloped Seat
2,3
Sloped / Skewed
1,2,3
Sloped Top Flange
4
Top Flange Offset
Saddle
5
Ridge
Range
1˚ to 50˚ 1˚ to 45˚ See Sloped Seat and Skewed 0˚ to 45˚ -- -- 0˚ to 45˚
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) Skewed hangers typically require a bevel cut however, a square cut option may be available as a custom when requested.
4) Sloped top flanges with slopes greater than 15° may have additional header nails.
5) Minimum header thickness shall be double the top flange (TF) dimension for 100% table load.
Ordering
Add
SK, angle required,
right
(R) or left (L), and
square cut
(SQ) or
bevel cut
(BV) to
product number. Ex.
HLBH3595_SK45R_BV
Allowable
Loads
8070 lbs. Max.
50% of uplift load on
skew greater than 15˚.
Add
SF, angle required,
and right
(R) or left (L),
to product number.
Ex.
HLBH3595_SF30L
7000 lbs. Max.
6650 lbs. Max.
50% of uplift load on
skew greater than 15˚.
Add
SL, slope required,
and up
(U) or down (D),
to product number.
Ex.
HLBH3595_SL30D
See Sloped Seat and Skewed.
Ex.
HLBH3595_SK45R_BV_SL30D
Add
OS, and
right
(R) or left (L),
to product number.
Ex.
HLBH3595_OSL
100% of table
load
45% of table load
100% of table load
per side.
See footnote 5.
100% of table load
Add
SA, and saddle
width required
to product number.
Ex.
HLBH3595_SA=5-1/2"
Add DA, and
angle required
to product number.
Ex.
HLBH3595_DA30
Nailer Options
– chart represents maximum allowable loads for hangers
used on wood nailers. Reference page 203.
Specialty Options Chart
– refer to Specialty Options pages 320, 322-323 for additional details
H
L
4-3/8"
D
TF
W