Use and Care Manual

230
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
EWP Hangers
TMP / TMPH Adjustable Rafter-To-Plate Connectors
The TMP and TMPH are designed to make rafter-to-plate
connections and eliminate time-consuming bird’s-mouth
notching or bevel plate installation. Both series are available
in I-Joists sizes, as well as standard 2x sizes.
TMP – Adjusts to pitches from 1/12 to 6/12
TMPH – Adjusts to pitches from 6/12 to 14/12
Ma terials: TMP – 18 gauge;
TMPH – 16 gauge, Fulcrum – 12 gauge
Finish: G90 galvanizing
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• Position connector on top plate. Fasten connector to
outside of top plate with specied nails. Insert rafter into
rafter pocket. Adjust rafter and pocket to correct pitch.
Fasten rafter to connector with specied nails. Installing
the TMP requires driving specied nails through the
opposing slots in the pocket. TMPH installation involves
sliding the fulcrum until it supports the pocket at the
desired pitch and nailing down through the fulcrum base
into the top plate to lock the fulcrum into position.
Typical TMPH
installation
Typical TMP
installation
TMPHTMP
Download Uplift Download Uplift
Ref. No. W L Qty Type Qty Type (100/115/125) 160% (100/115/125) 160%
1-1/2 TMP2 VPA2 18 1-9/16 5-9/16 6 10d 4 10d x 1-1/2
1705 245 1705 190
1-3/4 TMP175 VPA25 18 1-13/16 5-9/16 6 10d 4 10d x 1-1/2
1705 245 1705 185
2 or 2-1/8 TMP21
VPA2.06,
VPA2.1
18 2-1/8 6-3/8 6 10d 4 10d x 1-1/2
1705 245 1705 185
2-5/16 TMP23 VPA35 18 2-3/8 6-3/8 6 10d 4 10d x 1-1/2
1705 245 1705 185
2-1/2 or 2-5/8 TMP25 VPA3 18 2-11/16 6-3/8 6 10d 4 10d x 1-1/2
1705 245 1705 185
3 TMP31 -- 18 3-1/8 7-5/16 6 10d 4 10d x 1-1/2
1705 245 1705 185
3-1/2 TMP4 VPA4 18 3-9/16 7-5/16 6 10d 4 10d x 1-1/2
1705 245 1705 185
1) Allowable loads may not be increased for duration of load adjustments.
2)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long.
New products or updated product information are designated in
blue font
.
Code
Ref.
IBC,
FL,
LA
Rafter
Width (in)
S-P-F
Allowable Loads (Lbs.)
1
Dimensions (in)
Fastener Schedule
2
Plate Rafter
DF/SP
Allowable Loads (Lbs.)
1
MiTek USP
Stock No.
Steel
Gauge
Top Side
Ref. No. W H L Qty Qty Type Qty Type 6/12 7/12 8/12 9/12 10/12 11/12 12/12 13/12 14/12
1-1/2 TMPH2 VPA2 1-9/16 2-1/2 6-9/16 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
1-3/4 TMPH175 VPA25 1-13/16 2-3/8 6-9/16 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
2 or
2-1/8
TMPH21
VPA2.06,
VPA2.1
2-1/8 2-5/8 7-3/8 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
2-5/16 TMPH23 VPA35 2-3/8 2-1/2 7-3/8 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
3 TMPH31 -- 3-1/8 2-11/16 8-9/16 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
3-1/2 TMPH4 VPA4 3-9/16 2-1/2 8-9/16 8 2 10d 8 10d x 1-1/2 3190 3290 3390 3140 2900 2710 2520 2230 1950
330
1) Allowable loads may not be increased for duration of load adjustments.
2) Web stiffeners are required for all Wood I-Joist installations.
3)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long.
New products or updated product information are designated in
blue font
.
Uplift
160%
2710 2520 2230 1950
330
3190 3290 3390 3140 2900
2-1/2 or
2-5/8
Rafter
Width (in)
TMPH25 VPA3 2-11/16
IBC,
FL,
LA
Code
Ref.
According to Pitch
MiTek USP
Stock No.
Dimensions (in)
Fastener Schedule
3
Plate
Rafter
2
DF/SP
Allowable Loads (Lbs.)
1
2-5/16 7-3/8 8 2 10d 8 10d x 1-1/2
3-1/2"
L
W
Pitch Range:
TMP - 1/12 – 6/12
TMPH - 6/12 – 14/12
L
4"
4-11/16"
Fulcrum
H
W
TMP Chart
TMPH Chart