Use and Care Manual

270
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Plated Truss
Plated Truss
MiTek
®
Product Catalog
Materials: 12 gauge
Finish: G90 galvanizing
Options: See chart for Corrosion Finish Options and page 271 for
Specialty Options chart
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• Joist nails must be driven in at a 30° to 45° angle through the joist
or truss into the header to achieve listed loads. Slant/double
shear nails must be used to achieve listed load values.
• See EWP applications pages 214-216.
THDH Heavy-Duty Truss Hangers
Floor
Uplift
1
Floor
Uplift
1
Ref. No. W H D A Qty Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
2 x 6 - 8 THDH26 HGUS26 1-5/8 5-7/16 5 3-1/2 20 16d 8 16d 4375 4895
5180 2805
3850
4145 4145 2240
2 x 8 - 10 THDH28 HGUS28 1-5/8 7-3/16 5 3-1/2 36 16d 12 16d 7595
8175 8175 4345
6240
6585 6585 3500
2 x 10 - 12 THDH210 -- 1-5/8 9-3/16 5 3-1/2 46 16d 16 16d 9310 9710 9710
5290
7255 7770 7870
4285
2-11/16 x 9-1/4 - 14 THDH27925 -- 2-3/4 9-1/8 4 2-1/2 46 16d 12 16d 9020 9020 9020
4345
7515
7850 7850 3480
2-11/16 x 11-1/4 - 16 THDH27112 -- 2-3/4 10-7/8 4 2-1/2 56 16d 14 16d 9710 9710 9710
4345
7795 7795 7795
3490
2-11/16 x 14 - 16 THDH2714 -- 2-3/4 12-1/4 4 2-1/2 66 16d 16 16d 11185
11325 11325 5290
8530 9045
9115 4260
3-1/4 x 9-1/2 THDH3210 HGUS3.25/10 3-1/4 9-3/8 4 2-1/2 46 16d 12 16d 9020 9020 9020
4345 7830 7830 7830 3470
3-1/4 x 10-5/8 THDH3212 HGUS3.25/12 3-1/4 10-5/8 4 2-1/2 56 16d 14 16d 9710 9710 9710
5290
7775 7775 7775
4235
(2) 2 x 6 - 8 THDH26-2 HGUS26-2 3-1/4 5-1/2 4 2-1/2 20 16d 8 16d 4375 4895
5180 2805
3850
4120 4120 2230
(2) 2 x 8 - 10 THDH28-2 HGUS28-2 3-1/4 7-1/4 4 2-1/2 36 16d 10 16d 7360
8175 8175 3000
6475
6520 6520 2390
(2) 2 x 10 - 12 THDH210-2 HGUS210-2 3-1/4 9-1/4 4 2-1/2 46 16d 12 16d 9020 9020 9020
4345 7835 7835 7835 3475
4 x 6 - 8 THDH46 HGUS46 3-5/8 5-5/16 4 2-1/2 20 16d 8 16d 4375 4895
5180 2805
3850
4115 4115 2225
4 x 8 - 10 THDH48 HGUS48 3-5/8 7-1/16 4 2-1/2 36 16d 10 16d 7360
8175 8175 3000 6475 6505 6505 2385
4 x 10 - 12 THDH410 HGUS410 3-5/8 9-1/16 4 2-1/2 46 16d 12 16d 9020 9020 9020
4345 7820 7820 7820 3470
4 x 12 - 14 THDH412 HGUS412 3-5/8 11-1/16 4 2-1/2 56 16d 14 16d 9710 9710 9710
5290
7765 7765 7765
4230
4 x 14 - 16 THDH414 HGUS414 3-5/8 13-1/16 4 2-1/2 66 16d 16 16d
11325 11325 11325 5305 9075 9075 9075 4250
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) Joist nails need to be toe nailed at a 30° to 45˚ angle to achieve allowable loads shown.
3)
NAILS:
16d nails are 0.162" dia. x 3-1/2" long.
New products or updated product information are designated in
blue font
.
IBC,
FL,
LA
Joist /
Truss Size
MiTek USP
Stock No.
Fastener Schedule
3
Header
Truss
2
Code
Ref.
Roof Roof
DF/SP
Allowable Loads (Lbs.)
S-P-F
Allowable Loads (Lbs.)
Corrosion
Finish
Dimensions (in)
Some model designs
may vary from
illustration shown
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Continued on next page
Typical THDH installation
Drive joist nails into
header at 30° to 45°
to achieve listed loads.
Typical bend line
nail installation
Drive bend line nails
into header at 45° to
achieve listed loads.
THDH
H
D
W
Obround hole nailing
where applicable
Bend line nailing
where applicable
Typical double
shear installation
A