Use and Care Manual

276
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Plated Truss
Plated Truss
MiTek
®
Product Catalog
MSHL/R Skewed Truss Hangers
The MSHL/R is a versatile 45° skewed hanger with multiple
installation options. It can be installed on a supporting girder truss
as well as solid-sawn and structural composite lumber headers.
Materials: See chart
Finish: G90 galvanizing
Codes: See chart for code references
Installation:
• Install the required number of fasteners according to the load table.
• Install fasteners into the carrying members at the locations
described below based on the proper “Mounting Condition.”
• Web stiffeners are required for I-Joist installations.
• Hanger is factory skewed at 45° left or right.
Typical MSH213R installation
Right skew
Typical MSH213L installation
Left skew
Uplift
1
Uplift
1
Ref. No. Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
face-max -- 22 10d 6 10d x 1-1/2
1770 1770 1770 670 1430 1430 1430 540
top-max 4 6 10d 6 10d x 1-1/2
1810 1810 1810 670 1460 1460 1460 540
top-min 4 2 10d 6 10d x 1-1/2
1325 1325 1325
--
1240 1240 1240
--
combination 2 14 10d 6 10d x 1-1/2
1770 1770 1770 670 1430 1430 1430 540
face-max -- 14 10d 6 10d 1750
1755 1755 560 1395 1395 1395 445
top-max 4 6 10d 6 10d 1820 1820 1820
560 1490 1490 1490 445
top-min 4 2 10d 6 10d
1385 1385 1385
--
1100 1100 1100
--
combination 2 10 10d 6 10d 1750
1755 1755 560 1395 1395 1395 445
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long.
New products or updated product information are designated in
blue font
.
Header
S-P-F
Allowable Loads (Lbs.)
Joist
Material
& Width
MiTek USP
Stock No. GA
Mounting
Condition
Joist
Fastener Schedule
2
DF/SP
Allowable Loads (Lbs.)
Top
Qty
Face
Qty
Download Download
3-1/2" LVL
or Floor
Trusses
Code
Ref.
THAL/R422 16
2x Lumber
or
Trusses
-- MSH213L/R
MSH422L/R
18
IBC,
FL,
LA
MSH213L
Left skew
13-1/4"
5"
1-5/8"
1-3/4"
Right skew Left skew
Drive nails
at angle
40° to 50°
Typical MSHL/R
face-max installation
Typical MSHL/R
top-max installation
Typical MSHL/R
top-min installation
Typical MSHL/R
combination installation
Install six (6) 10d x 1-1/2" nails into 2x carried member, or six (6) 10d nails into 3-1/2" wide carried member.
CONNECTION TO CARRYING MEMBER – Mounting Condition
CONNECTION TO CARRIED MEMBER – All Mounting Conditions
Top-Max
The straps must be eld-bent over
the header a minimum of 2" to
allow four (4) top ange nail holes
to be lled (two in each strap). The
bottom six (6) fastener holes (three
on each side of the bucket) must
be lled. Min. 2x6 bottom chord
required.
Top-Min
The straps must be eld bent over
the header a minimum of 2" to
allow four (4) top ange nail holes
to be lled (two in each strap). Also
install the two (2) uppermost face
nails (one on each strap) near the
top of the header.
MSH422R
Right skew
MSH422L
Left skew
22"
5-1/8"
1-3/4"
3-9/16"
9-5/16"
Combination
Face-Max/Top-Max
Follow the Face-Max installation
for one side of the connector and
the Top-Max installation for the
opposite side of the connector.
The Face-Max allowable loads
apply to this type of installation.
Min. 2x6 bottom chord required.
1) Uplift loads have been
increased 60% for wind
or seismic loads; no
further increase shall
be permitted.
2) NAILS: 10d x 1-1/2
nails are 0.148" dia. x
1-1/2" long, 10d nails
are 0.148" dia. x 3" long
New products or updated
product information are
designated in blue font.
Face-Max
For MSH422L/R, the bottom six (6)
fastener holes (three on each side of
the bucket) must be lled. Install eight
additional fasteners (four (4) in each
strap) where applicable. For MSH213L/R,
the bottom eight (8) fastener holes must
be lled (four (4) in each strap). Install
fourteen (14) additional fasteners, seven
(7) in each strap. Min. 2x6 bottom chord
required.