Use and Care Manual

279
Plated Truss
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Plated Truss
MiTek
®
Product Catalog
Floor
Uplift
1
Floor
Uplift
1
Ref. No. W H Type Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
22-1/2 -- 12 10d 7 10d x 1-1/2 1500 1615 1615 975 1250 1275 1275 770
23 to 45 -- 12 10d 4 10d x 1-1/2 1485 1485 1485 560 1250 1350 1350 435
46 to 75 -- 12 10d 4 10d x 1-1/2 1500 1615 1615 720 1250 1315 1315 560
22-1/2 4 8 10d 7 10d x 1-1/2 1985 1985 1985 975 1510 1510 1510 745
23 to 45 4 8 10d 4 10d x 1-1/2 1705 1705 1705 560 1255 1255 1255 415
46 to 75 4 8 10d 4 10d x 1-1/2 1605 1605 1605 720 1605 1605 1605 560
22-1/2 4 4 10d 7 10d x 1-1/2 1350 1350 1350 -- 1045 1045 1045 --
23 to 45 4 4 10d 4 10d x 1-1/2 1335 1335 1335 -- 1060 1060 1060 --
46 to 75 4 4 10d 4 10d x 1-1/2 695 695 695 -- 695 695 695 --
22-1/2 -- 12 10d 7 10d 1500 1615 1615 975 1215 1215 1215 735
23 to 45 -- 12 10d 4 10d 1485 1485 1485 560 1210 1260 1260 405
46 to 75 -- 12 10d 4 10d 1500 1615 1615 720 1250 1300 1300 555
22-1/2 4 8 10d 7 10d 1985 1985 1985 975 1495 1495 1495 735
23 to 45 4 8 10d 4 10d 1705 1705 1705 560 1275 1275 1275 420
46 to 75 4 8 10d 4 10d 1605 1605 1605 720 1565 1565 1565 535
22-1/2 4 4 10d 7 10d 1350 1350 1350 -- 1040 1040 1040 --
23 to 45 4 4 10d 4 10d 1335 1335 1335 -- 1060 1060 1060 --
46 to 75 4 4 10d 4 10d 695 695 695 -- 695 695 695 --
22-1/2 -- 12 10d 7 10d 1500 1590 1590 960 1250 1250 1250 755
23 to 45 -- 12 10d 4 10d 1485 1485 1485 550 1250 1335 1335 430
46 to 75 -- 12 10d 4 10d 1500 1615 1615 705 1250 1300 1300 555
22-1/2 4 8 10d 7 10d 1955 1955 1955 960 1490 1490 1490 735
23 to 45 4 8 10d 4 10d 1680 1680 1680 550 1270 1270 1270 420
46 to 75 4 8 10d 4 10d 1605 1605 1605 705 1565 1565 1565 535
22-1/2 4 4 10d 7 10d 1330 1330 1330 -- 1040 1040 1040 --
23 to 45 4 4 10d 4 10d 1335 1335 1335 -- 1060 1060 1060 --
46 to 75 4 4 10d 4 10d 695 695 695 -- 695 695 695 --
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) H
eff
is the minimum distance
f
rom the top o
f
the hanger seat to the top o
f
the carrying member.
3) For tabulated top-mount installation loads, the straps must be wrapped over the header a minimum of 2".
4) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long.
3-1/8
10-3/4
10-3/4
Dimensions
(in)
4x
Trusses
2-2x
Trusses
MSHA29L/R
MSHA29L/R-2
THASR/L29
THASR/L29-2
2x
Trusses
Carrying
Member
Carried
Member
Joist
Material
& Width
MiTek USP
Stock No.
1-5/8
7-1/4
5-1/2
7-1/4
5-1/2
face-max
--
face-max
face-max
top-min
top-max
Top
Qty
Face
Qty
MSHA422L/R THASR/L422
top-min
top-max
top-min
3-5/8 22
Mounting
Condition
3
Skew
Angle
(degrees)
Fastener Schedule
4
Min
H
eff
2
(in)
top-max
7-1/4
5-1/2
Code
Ref.
Roof Roof
DF/SP
Allowable Loads (Lbs.)
S-P-F
Allowable Loads (Lbs.)
MSHA Adjustable Strap Skewed Hangers
Installation Sequence for Skews > 22½°:
Step 1: Install acute side top
and/or face header nails.
Step 2: Utilizing a piece of scrap
fastened to the hanger on the
obtuse side, bend the hanger
to the desired angle.
Step 3: Bend the obtuse side of
hanger back toward the header
until the ange lies at against
the header, and install header top
and/or face nails as noted below.
Step 4: Install carried truss
and all required nails fasteners
working from the bottom up.
Rotate
acute
side to
desired
angle
Align back edge of carried
member with the slotted holes
on the acute side