Use and Care Manual

281
Plated Truss
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Plated Truss
MiTek
®
Product Catalog
HHC / HJC / HJHC / HTHJ Hip/Jack Connectors
HHC – Designed to support hip/hip truss/rafter. Contact MiTek when using in multi-ply applications
HJHC – Allows for hip/hip support and hip/jack/hip installations
HJC / HTHJ – Used to simultaneously hang a combination of hips and jacks off girder trusses. These
hangers t both left-hand and right-hand applications. An open back design allows for retrot installations
Materials: HHC/HJC/HJHC – 12 gauge, HTHJ –18 gauge
Finish: G90 galvanizing
Options: See HJC Specialty Options Chart below
Codes: See chart for code references
Installation:
• Use all specied fasteners. See Product Notes, page 18.
Typical HJC/HTHJ
installation
Typical HJC/HTHJ installation top view
HJC
Typical HHC
installation top view
Typical HJC (skewed) installation
with alternate skew angle top view
HHCHTHJ
Typical HJHC
installation top view
HJC (skewed)
HJHC
Floor
Uplift
1
Floor
Uplift
1
Description Ref. No. Qty Type Qty Qty Type 100% 115% 125% 160% 100% 115% 125% 160%
2 x 6 right / left HJC26
LTHJA26,
THJA26,
THJU26
12 5-3/8 16 16d 5 7 10d 2750 3055 3265 2345
2420 2685 2750 1905
2 x 8 right / left HJC28 -- 12 7-1/8 20 16d 6 8 10d 3385 3385 3385 2345 2760 2760 2760 1910
2 x 6 terminal HHC26
LTHJA26,
THJA26
12 5-7/16 20 16d 5 -- 10d 3100 3505 3505 2130 2725 2800 2800 1870
2 x 8 terminal HHC28 -- 12 7-3/16 24 16d 6 -- 10d 3505 3505 3505 2410 2805 2805 2805 1930
2 x 6 terminal HJHC26 -- 12 5-7/16 20 16d 5 2 10d 3100 3505 3505 2410 2725 2815 2815 1935
2 x 8 terminal HJHC28 -- 12 7-3/16 24 16d 6 2 10d 3505 3505 3505 2410 2820 2820 2820 1940
2 x 6 terminal HTHJ26-18 -- 18 5 16 16d 7 5 16d
2295 2605 2695 1790 1985 2110 2110 1225
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) Loading published for total load of hip / jack connection.
3)
NAILS:
10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
New products or updated product information are designated in
blue font
.
--
MiTek USP
Stock No.
Steel
Gauge
RoofRoof
H
(in)
Supported Member
IBC,
FL,
LA
Fastener Schedule
3
Code
Ref.
DF/SP
Allowable Loads (Lbs.)
2
S-P-F
Allowable Loads (Lbs.)
2
per
Hip
per
Jack
Supporting
Member
Option Hip Truss Skew
Range
30˚ to 60˚
Allowable Loads
100% of table load
Ordering
Add SK, angle of hip
required, to product number.
Ex. HJC26_SK55
HJC Specialty Options Chart
– Refer to Specialty Options pages 320-321 for additional details.
45°
45°
Specify angle
(60° max)
45°
45°
45°
45°
6"
3-1/4"
1-3/4"
H
5"
5-7/8"
2"
H
9"
1-7/8"
3-1/4"
H
10-1/2"
1-3/4"
3-1/4"
H
Varies
8" max. width
H
3-1/4"
1-3/4"