Use and Care Manual

302
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Deck & Fences
Deck & Fences
MiTek
®
Product Catalog
DC Deck Clip
Connects deck boards to joists without face nails or screws. Eliminates rust stains
on decks, as well as splintering or wood rot caused by screw or nail “craters”.
The DC50-TZ works like tongue-in-groove ooring and is easy to install. Raised
dimples on the clip provide consistent spacing between deck boards.
Materials: 20 gauge
Finish: G-185 galvanizing
Options: See chart for Corrosion Finish Options
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• Fits 1-1/8" or thicker decking.
• Fasten the rst deck board onto the joists by toenailing up through the joist below
into the deck board. Be sure no sharp points protrude above the deck surface. For
subsequent deck board rows, nail DC50-TZ's onto the deck board edge, positioned
2" from each joist. Slide the deck board along the joist until the DC50-TZ “lip” is
under the previously laid deck board. Toenail the deck board’s exposed edge
to the joist. Repeat until decking is completed. The last deck board will require
toenailing up from below to secure the outside edge.
ML angles are multi-purpose angles that install easily with MiTek’s
WS15 structural wood screws. The staggered fastener pattern
allows for back-to-back installations.
Materials: 12 gau ge
Finish: G-185 galvanizing
Options: See chart for Corrosion Finish Options
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• MiTek’s WS15 (1/4" dia x 1-1/2" long) structural wood screws
are not supplied with ML angles.
Typical DC50-TZ
installation
Typical ML26-TZ
installation
(ML24-TZ similar)
DC50-TZ
ML26-TZ
(ML24-TZ similar)
Ref. No. Qty Type
DC50-TZ DBT1Z 20 1 8d x 1-1/2 HDG --
1) Use with 1-1/8" or thicker wood decking.
2)
NAILS:
8d x 1-1/2 nails are 0.131" dia. x 1-1/2" long.
MiTek USP
Stock No.
Steel
Gauge
Code
Ref.
Corrosion
Finish
Fastener
Schedule
1,2
ML Angles
F1
H
W
W
Ref. No. W H Type 100% 115% 125% 160% 100% 115% 125% 160%
ML24-TZ ML24Z 12 2 4 3 3 WS15
655
655
655
655
565
650
655
655
ML26-TZ ML26Z 12 2 6 4 4 WS15 920 1060
1090
1090
755 865
940
1090
1) Allowable loads have been increased 60% for wind and seismic loads; no further increase shall be permitted.
2) MiTek's WS15 structural wood screws are 1/4" dia. x 1-1/2" long and are not included with angles.
3) For exterior applications use MiTek's WS15-EXT structural wood screws with exterior coat finish.
New products or updated product information are designated in
blue font
.
IBC,
FL, LA
MiTek USP
Stock No.
Steel
Gauge
F1 F1
Corrosion
Finish
DF/SP
Allowable Loads (Lbs.)
1
S-P-F
Allowable Loads (Lbs.)
1
Dimensions
(in)
Code
Ref.
Header
Qty
Joist
Qty
Fastener
Schedule
2,3
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish
Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc