Use and Care Manual

336
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Cold-Formed Steel Connectors
CFS Connectors
MiTek
®
Product Catalog
HDO/S / HDOL/S Top Mount Bridle Hangers
HDOL/S (14 ga) and HDO/S (12 ga) top mount bridle hangers
are available in a wide variety of stock sizes to match the most
common framing needs with economical solutions where custom
or special order hangers were required before. The revolutionary
design utilizes shear lag slots designed to maximize the capacity
of the hangers while providing a safe and ductile connection.
The HDOL/S and HDO/S hangers may be installed with screws,
powder actuated, or welded to the header.
Ma terials: HDOL/S 68mil (14 gauge), HDO/S 97mil (12 gauge)
Finish: G90 galvanizing
Patents: U.S. Patent No. 10,662,641, U.S. Patent No. 10,072,412
Installation:
• Install prescribed type and number of self-drilling screws in
to the round holes of the hangers. Do not install screws in the
shear lag slots.
• Powder actuated fasteners are permitted.
• Welding of the hangers is permitted. Place a minimum 1/8" x 2"
llet weld on each top ange of the hanger. Welding should be
performed by a qualied welder using a qualied welding pro-
cedure while distributing the weld evenly across both anges.
Weld-on applications produce maximum allowable load listed.
Uplift loads do not apply to this application.
Ref. No. W H D
Type
4
Qty
Type
4
HDOL/S1606 S/LBV1.68/6 14 3 4 6 2950
HDO/S1606 S/B1.68/6 12 3-1/2 6 8 6140
HDOL/S1608 S/LBV1.68/8 14 3 4 6 2950
HDO/S1608 S/B1.68/8 12 3-1/2 6 8 6140
HDOL/S1610 S/LBV1.68/10 14 3 4 6 2950
HDO/S1610 S/B1.68/10 12 3-1/2 6 8 6140
HDOL/S1612 S/LBV1.68/12 14 3 4 6 2950
HDO/S1612 S/B1.68/12 12 3-1/2 6 8 6140
HDOL/S2006 S/LBV2.06/6 14 3 4 6 2950
HDO/S2006 S/B2.06/6 12 3-1/2 6 8 6140
HDOL/S2008 S/LBV2.06/8 14 3 4 6 2950
HDO/S2008 S/B2.06/8 12 3-1/2 6 8 6140
HDOL/S2010 S/LBV2.06/10 14 3 4 6 2950
HDO/S2010 S/B2.06/10 12 3-1/2 6 8 6140
HDOL/S2012 S/LBV2.06/12 14 3 4 6 2950
HDO/S2012 S/B2.06/12 12 3-1/2 6 8 6140
HDOL/S4006 S/LBV4.06/6 14 3 4 6 2950
HDO/S4006 S/B4.06/6 12 3-1/2 6 8 6140
HDOL/S4008 S/LBV4.06/8 14 3 4 6 2950
HDO/S4008 S/B4.06/8 12 3-1/2 6 8 6140
HDOL/S4010 S/LBV4.06/10 14 3 4 6 2950
HDO/S4010 S/B4.06/10 12 3-1/2 6 8 6140
HDOL/S4012 S/LBV4.06/12 14 3 4 6 2950
HDO/S4012 S/B4.06/12 12 3-1/2 6 8 6140
1) Testing of HDOL/S and HDO/S hangers was performed with framing members with minimum steel yield strengths of Fy=50 ksi.
2) Qualified designer shall design connection to ensure the header is designed to carry the load and the joist member is sufficient to transfer load to hanger.
3) Allowable loads based on testing with 68 mil (14ga) CFS members for the HDOL/S hanger and 97 mil (12ga) CFS members for the HDO/S hanger.
4) #10 screws are ITW Buildex 10-16 HWH Teks Structural Fasteners with a nominal diameter of 0.190". Self-drilling tapping screws with equivalent physical
and strength properties may be used.
Code
Ref.
--
2 10
4 10
4 12
2 12
46
48
#10
1-5/8
#10
#10
#10
3
3
#10
3 #10
3 #10#10
3 #10
3 #10
3 #10
3 #10
3 #10
3 #10
3 #10
3
#10
#10
#10
#10
#10
#10
#10
1-5/8
1-5/8 8 #10
#10
26
28
6
10
1-5/8 12
MiTek
Stock No.
Steel
Gauge
Down
100%
Dimensions (in) Fastener Schedule
Allowable
Loads
1,2,3
Header Joist
Top
Qty
Face
Qty
Typical HDOL/S1616
(I-beam) installation
Top view detail of welds
HDOL/S1606 HDOL/S2010 HDOL/S4012
Typical HDOL/S2010
(CFS Header) installation
Typical HDOL/S4012
(I-beam) installation
W
D
H
W
D
H
W
D
H
2"
1/8" 2"
1-1/2"
Install screws
in the round holes.
Do not install in
slotted holes.