Use and Care Manual
188
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Lumber Hangers
Lumber Hangers
MiTek
®
Product Catalog
MPH Masonry Hangers
These hangers are designed to support standard lumber
joists, I-Joists, or beams. Easy installation into concrete
block walls makes the MPH an attractive alternative to
fabricating seats in masonry (or attaching ledgers) to
support joists or beams.
Materials: 12 gauge
Finish: Primer
Options: All nominal lumber sizes are available for rough
full size lumber. See Specialty Options Chart on page 189.
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• 16d duplex nails are not supplied with MPH hangers.
• Place hanger into position on top of concrete block.
Install (2) 16d duplex nails (0.162" dia. x 3-1⁄2" double
head) through the top ange nail holes. Then continue
laying the next course of block.
• A minimum of one course shall be laid over hanger top
ange and one course below hanger top ange. Courses
adjacent to the top ange shall be subsequently grouted.
• These products do not provide uplift resistance.
Typical MPH
single-ply installation
Typical MPH
double-ply installation
Install with (2) 16d duplex
nails in grouted cells
Install with (2) 16d duplex
nails in grouted cell
Floor
Ref. No. W H L Qty Type Qty Type 100% 115% 125%
2 x 10 MPH210 WMU1.56/9.25 12 1-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
2 x 12 MPH212 WMU1.56/11.25 12 1-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
2 x 14 MPH214 WMU1.56/14 12 1-9/16 13-1/8 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
2 x 16 MPH216 WMU1.56/16 12 1-9/16 15-1/8 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
(2) 2 x 10 MPH210-2 WMU3.12/9.25 12 3-1/8 9-1/4 7 2 16d duplex 2 10d 4430 4430 4430
(2) 2 x 12 MPH212-2 WMU3.12/11.25 12 3-1/8 11-1/4 7 2 16d duplex 2 10d 4430 4430 4430
(2) 2 x 14 MPH214-2 WMU3.12/14 12 3-1/8 13-1/8 7 2 16d duplex 2 10d 4430 4430 4430
(2) 2 x 16 MPH216-2 WMU3.12/16 12 3-1/8 15-1/8 7 2 16d duplex 2 10d 4430 4430 4430
3 x 10 MPH310 WMU2.56/9.25 12 2-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 3295 3295 3295
3 x 12 MPH312 WMU2.56/11.25 12 2-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 3295 3295 3295
3 x 14 MPH314 WMU2.56/13.25 12 2-9/16 13-1/8 7 2 16d duplex 2 10d x 1-1/2 3295 3295 3295
3 x 16 MPH316 WMU2.56/15.25 12 2-9/16 15-1/8 7 2 16d duplex 2 10d x 1-1/2 3295 3295 3295
4 x 10 MPH410 WMU3.56/9.25 12 3-9/16 9-1/4 7 2 16d duplex 2 10d 4430 4430 4430
4 x 12 MPH412 WMU3.56/11.25 12 3-9/16 11-1/4 7 2 16d duplex 2 10d 4430 4430 4430
4 x 14 MPH414 WMU3.56/13.25 12 3-9/16 13-1/8 7 2 16d duplex 2 10d 4430 4430 4430
4 x 16 MPH416 WMU3.56/15.25 12 3-9/16 15-1/8 7 2 16d duplex 2 10d 4430 4430 4430
6 x 10 MPH610 WMU5.50/9.5 12 5-9/16 9-1/4 7 2 16d duplex 2 10d 4430 4430 4430
1-1/2 x 9-1/4 MPH210 WMU1.56/9.25 12 1-9/16 9-1/4 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
1-1/2 x 9-1/2 MPH1595 WMU1.56/9.5 12 1-9/16 9-1/2 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
1-1/2 x 11-1/4 MPH212 WMU1.56/11.25 12 1-9/16 11-1/4 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
1-1/2 x 11-7/8 MPH15118 WMU1.56/11.88 12 1-9/16 11-7/8 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
1-1/2 x 14 MPH1514 WMU1.56/14 12 1-9/16 14 7 2 16d duplex 2 10d x 1-1/2 2610 2650 2675
1-3/4 x 9-1/2 MPH1795 WMU1.81/9.5 12 1-13/16 9-1/2 7 2 16d duplex 2 10d x 1-1/2 3000 3040 3065
1-3/4 x 11-7/8 MPH17118 WMU1.81/11.88 12 1-13/16 11-7/8 7 2 16d duplex 2 10d x 1-1/2 3000 3040 3065
1-3/4 x 14 MPH1714 WMU1.81/14 12 1-13/16 14 7 2 16d duplex 2 10d x 1-1/2 3000 3040 3065
1-3/4 x 16 MPH1716 WMU1.81/16 12 1-13/16 16 7 2 16d duplex 2 10d x 1-1/2 3000 3040 3065
1
)
Masonr
y
com
p
ressive stren
g
th shall be minimum 1500
p
si.
2
)
NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" lon
g
, 10d nails are 0.148" dia. x 3" lon
g
, 16d du
p
lex nails are 0.162" dia. x 3-1/2" lon
g
,
double headed nails and shall be installed in
g
routed cells in accordance to manufacturer's installation s
p
ecifications.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
Floor
Ref. No. W H L Qty Type Qty Type 100% 115% 125%
2-5/16 x 9-1/2 MPH2395 WMU2.37/9.5 12 2-3/8 9-1/2 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-5/16 x 11-7/8 MPH23118 WMU2.37/11.88 12 2-3/8 11-7/8 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-5/16 x 14 MPH2314 WMU2.37/14 12 2-3/8 14 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-5/16 x 16 MPH2316 WMU2.37/16 12 2-3/8 16 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-5/16 x 18 MPH2318 WMU2.37/18 12 2-3/8 18 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-5/16 x 20 MPH2320 WMU2.37/20 12 2-3/8 20 7 2 16d duplex 2 10d x 1-1/2 3880 3920 3945
2-1/2 x 9-1/4 MPH25925 WMU2.56/9.25 12 2-1/2 9-1/4 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 9-1/2 MPH2595 WMU2.56/9.5 12 2-1/2 9-1/2 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 11-1/4 MPH25112 WMU2.56/11.25 12 2-1/2 11-1/4 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 11-7/8 MPH25118 WMU2.56/11..88 12 2-1/2 11-7/8 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 14 MPH2514 WMU2.56/14 12 2-1/2 14 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 16 MPH2516 WMU2.56/16 12 2-1/2 16 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 18 MPH2518 WMU2.56/18 12 2-1/2 18 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 20 MPH2520 WMU2.56/20 12 2-1/2 20 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 22 MPH2522 WMU2.56/22 12 2-1/2 22 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 24 MPH2524 WMU2.56/24 12 2-1/2 24 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
2-1/2 x 26 MPH2526 WMU2.56/26 12 2-1/2 26 7 2 16d duplex 2 10d x 1-1/2 4170 4210 4240
3 x 9-1/4 MPH210-2 WMU3.12/9.25 12 3-1/8 9-1/4 7 2 16d duplex 2 10d 4430 4430 4430
3 x 9-1/2 MPH1595-2 WMU3.12/9.5 12 3-1/8 9-1/2 7 2 16d duplex 2 10d 4430 4430 4430
3 x 11-1/4 MPH15112-2 WMU3.12/11.25 12 3-1/8 11-1/4 7 2 16d duplex 2 10d 4430 4430 4430
3 x 11-7/8 MPH15118-2 WMU3.12/11.88 12 3-1/8 11-7/8 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 12 MPH3512 WMU3.62/12 12 3-1/2 12 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 14 MPH3514 WMU3.62/14 12 3-1/2 14 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 16 MPH3516 WMU3.62/16 12 3-1/2 16 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 18 MPH3518 WMU3.62/18 12 3-1/2 18 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 20 MPH3520 WMU3.62/20 12 3-1/2 20 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 9-1/4 MPH410 WMU3.56/9.25 12 3-9/16 9-1/4 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 11-1/4 MPH412 WMU3.56/11.25 12 3-9/16 11-1/4 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 9-1/2 MPH1795-2 WMU3.56/9.5 12 3-5/8 9-1/2 7 2 16d duplex 2 10d 4430 4430 4430
3-1/2 x 11-7/8 MPH17118-2 WMU3.56/11.88 12 3-5/8 11-7/8 7 2 16d duplex 2 10d 4430 4430 4430
4-5/8 x 11-7/8 MPH23118-2 WMU4.75/11.88 12 4-5/8 11-7/8 7 2 16d duplex 2 10d 4430 4430 4430
4-5/8 x 14 MPH2314-2 WMU4.75/14 12 4-5/8 14 7 2 16d duplex 2 10d 4430 4430 4430
4-5/8 x 16 MPH2316-2 WMU4.75/16 12 4-5/8 16 7 2 16d duplex 2 10d 4430 4430 4430
4-5/8 x 18 MPH2318-2 WMU4.75/18 12 4-5/8 18 7 2 16d duplex 2 10d 4430 4430 4430
4-5/8 x 20 MPH2320-2 WMU4.75/20 12 4-5/8 20 7 2 16d duplex 2 10d 4430 4430 4430
5-1/4 x 9-1/2 MPH5595 WMU5.50/9.5 12 5-5/8 9-1/2 7 2 16d duplex 2 10d 4430 4430 4430
5-1/4 x 11-7/8 MPH55118 WMU5.50/11.88 12 5-5/8 11-7/8 7 2 16d duplex 2 10d 4430 4430 4430
7 x 9-1/2 MPH3595-2 WMU7.12/9.5 12 7-1/8 9-1/2 8 2 16d duplex 2 10d 4490 4490 4490
7 x 11-1/4 MPH35112-2 WMU7.12/11.25 12 7-1/8 11-1/4 8 2 16d duplex 2 10d 4490 4490 4490
7 x 11-7/8 MPH35118-2 WMU7.12/11.88 12 7-1/8 11-7/8 8 2 16d duplex 2 10d 4490 4490 4490
7 x 14 MPH3514-2 WMU7.12/14 12 7-1/8 14 8 2 16d duplex 2 10d 4490 4490 4490
7 x 16 MPH3516-2 WMU7.12/16 12 7-1/8 16 8 2 16d duplex 2 10d 4490 4490 4490
7 x 18 MPH3518-2 WMU7.12/18 12 7-1/8 18 8 2 16d duplex 2 10d 4490 4490 4490
3-1/8 x glulam MPH325 WMU3.25X 12 3-1/4 specify 7 2 16d duplex 2 10d 4430 4430 4430
5-1/8 x glulam MPH525 WMU5.25X 12 5-1/4 specify 7 2 16d duplex 2 10d 4430 4430 4430
1
)
Masonr
y
com
p
ressive stren
g
th shall be minimum 1500
p
si.
2
)
NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" lon
g
, 10d nails are 0.148" dia. x 3" lon
g
, 16d du
p
lex nails are 0.162" dia. x 3-1/2" lon
g
,
double headed nails and shall be installed in
g
routed cells in accordance to manufacturer's installation s
p
ecifications.
New
p
roducts or u
p
dated
p
roduct information are desi
g
nated in blue font.
Steel
Gauge
Roof
IBC,
FL,
LA
Dimensions (in)
Steel
Gauge
Block Joist
Roof
Fastener Schedule
2
DF/SP
Allowable Loads (Lbs.)
1
Engineered Lumber Sizes
Standard Lumber Sizes
Glulam Sizes
IBC,
FL, LA
Beam/
Joist Size
MiTek USP
Stock No.
Code
Ref.
IBC,
FL,
LA
Engineered Lumber Sizes
Dimensions (in)
Fastener Schedule
2
DF/SP
Allowable Loads (Lbs.)
1
Block
IBC,
FL,
LA
Code
Ref.
Joist
Beam/
Joist Size
MiTek USP
Stock No.
MPH
H
2-1/2"
3-3/4"
W
L
Continued on next page