User's Manual

3
Hardware Features (See Figure
A
)
Feature Description
LED indicator Blue -
Indicates the status of the handset.
Green -
Indicates the status of the handset battery.
Hookswitch key Lifting the handset from the cradle activates
the handset. If the
handset is already out of the cradle, pressing the Hookswitch key
is equivalent to taking the handset off hook.
Pressing the key again is equivalent to placing the handset on
hook.
Pressing the Hookswitch key while on a speakerphone call moves
the call to the handset.
Mute key Mutes the handset microphone so that your caller cannot hear
you.
Volume control
keys
Adjusts the volume for the handset. Press the key above the Mute
key
to increase the volume and press the key below the mute key
to decrease the volume.
NOTE: The Mitel Cordless Bluetooth Handset must be fully charged before
use. This will typically take three hours. A new, fully-charged handset battery
has a talk time of six hours.
LED Indicators
The Mitel Cordless Bluetooth Handset has two LEDs:
• Blue – indicates the operational status of the handset.
• Green – indicates the status of the electrical charge of the battery.
LED color, states
LED
Color
*LED
State
Indicates
Blue
(Handset
no
t in
cradle)
Blinking The handset is not connected and is in pairing mode.
Winking The handset is connected but not in use.
Fading The handset is connected and in use.
Green
(Handset
in
cradle)
Solid The battery is fully charged.
Winking The battery is charging.
Note:
It is normal for the handset LED to cycle between
winking and solid as battery charge is maintained.
Off When the handset is cradled and the LED does not flash or
illum
inate, this indicates an absence of battery power. During
the first 30 to 60 minutes that the light is off, the battery may
be trickle charging. If that is the case, the LED will resume
normal behavior within that 60 minute period. If the LED
remains off for more than 60 minutes, then either the battery
is no longer chargeable or there is a problem in the charging
circuit.
, and indicator descriptions are as follows:
*NOTE:
Blinking denotes the LED is alternating very quickly between on and
off. Winking denotes the LED is alternating between being on for a short period
of time and then off for a longer period of time. Fading denotes the LED is
alternating between fading in and out.
On-Screen Battery Indicator
The battery level is also indicated on-screen in the status bar. Icons and
descriptions are as follows:
Icon Description
Battery is fully charged.
Battery is two-thirds charged.
Battery is one-third charged.
Warning - low battery (within 20 minutes of battery life left).
Critical warning - low battery (within 2 minutes of battery life left).
Note: To continue with a
call when the battery of the handset reaches this
level, switch to speakerphone or headset mode and then charge the 
handset by placing the handset on the cradle (see Figure B).
Alerting Tones
The Mitel Cordless Bluetooth Handset provides the following alerting tones:
Event Tone
Power OFF Four tones successively decreasing in pitch
Mute key on handset ON Two low pitched tones
Powering On/Off the Handset
To power on the Mitel Cordless Bluetooth Handset place the handset on the IP
phone’s cradle.
To power off the Mitel Cordless Bluetooth Handset, press the Ho
okswitch key
for approximately six seconds until the LED indicator turns blue and then turns
completely off.
Pairing the Handset with the Mitel MiVoice 6930 IP Phone
1. Ensure the Mitel Cordless Bluetooth Handset is powered on.
NOTE:
To check if the Mitel Cordless Bluetooth Handset is in pairing mode,
take the handset off the IP phone’s cradle and check the LED indicator. The
handset’s blue LED blinks when it is in pairing mode.
2. Press the (Settings) key on the phone to enter the Static
Settings me
nu.
3. Navigate to the Blue
tooth setting and press the Select softkey.
4. Ensure Bluetooth functionality is enabled
. If it is not enabled, press the
Turn On softkey to enable Bluetooth functionality.
5. If required, press the down navigation key to view the list of A
vailable 
Devices.
6. Press the right navigation key to move to the Bluetooth device selection
col
umn.
7. Using the up and down navigation keys, highlight Cord
less Handset and
press the Pair softkey. The phone attempts to pair the Bluetooth handset
and if successful, automatically attempts to connect.
NOTE:
If pairing or connecting fails, a failed error message displays on screen.
Press Retry to attempt to pair or connect again, or Cancel to cancel the
attempt.