User's Manual

4
8. Press OK to acknowledge the successful connection. The MWI indicator
on the phone flashes blue when successfully connected and the handset
LED starts to wink. The connected Bluetooth handset is added to the list
of Paired Devices and is ready to use.
Pairing the Handset with the Mitel MiVoice 6940 IP Phone
1. Ensure the Mitel Cordless Bluetooth Handset is powered on.
NOTE:
To check if the Mitel Cordless Bluetooth Handset is in pairing mode,
take the handset off the IP phone’s cradle and check the LED indicator. The
handset’s blue LED blinks when it is in pairing mode.
2. Press the (Settings) key on the phone to enter the Static
Settings menu.
3. Tap the Bl
uetooth icon.
4. Ensure Bluetooth functionality is enabled. If it is not enabled, swipe the
Blue
tooth toggle switch
to the right to enable Bluetooth
functionality.
5. If required, tap A
vailable Devices to view the list of discoverable 
Bluetooth devices.
6. Tap Cord
less Handset to start the pairing process. The phone attempts
to pair the Bluetooth handset and if successful, automatically attempts to
connect.
NOTE:
If pairing or connecting fails, a failed error message displays on
screen. Tap
Retry to attempt to pair or connect again, or Cancel to cancel the
attempt.
7. Tap OK to acknowledge the successful connection. The MWI indicator on
the phone flashes blue when successfully connected and the handset
LED starts to wink. The connected Bluetooth handset is added to the list
of Paired Devices and is ready to use.
For information on handset usage, refer to the respective Mitel MiVoice 6900
Series IP Phone User Guide.
Replacing the Battery
Your Mitel Cordless Bluetooth Handset uses
a 350maH Lithium-Ion Polymer
(LiPo)
rechargeable battery. If your Mitel Cordless
Bluetooth Handset fails to hold a charge, it
may be time to replace the battery.
WARNING: US
E ONLY A MITEL
APPROVED REPLACEMENT BATTERY
(PART NUMBER 50006764).
To replace the battery:
1. Locate the battery cover (see Figure A).
2. Unscrew the battery cover screw using
a Philli
ps PH1 screwdiver and remove
the battery cover.
3. Remove the old battery pack from the
ba
ttery compartment by disconnecting
the red and black wired connector from
the plug located in the battery
compartment.
4. Connect the new battery’s red and black
wired con
nector to the plug and
carefully place the new battery in the
battery compartment.
5. Place the battery cover back on the
ha
ndset and and fasten using the screw
attached to the battery cover.
Notice to Canadian Customers
IC: 173A-AQUA1
This device complies with Industry Ca
nada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-3 (B)/NMB-3(B).
Avis aux clients canadiens
IC: 173A-AQUA1
Le présent appareil est conforme aux C
NR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Cet appareil numérique de la classe B es
t conforme à la norme NMB-003 du
Canada.
RF Exposure Canada
This device is compliant to the RF exposure requirements in Industry Canada
RSS-102 issue 5.
Exposition RF Canada
Conformité des appareils de radiocommunication aux limites d'exposition
humaine aux radiofréquences (toutes bandes de fréquences)
Notice to U.S. Customers
FCC ID: EHTAQUA1
This device complies with part 15 of the FCC Rules. Operation is subject to the
f
ollowing two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circ
uit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
NOTE:
Changes or modifications not expressly approved by Mitel Networks ™
Corporation may void the user’s right to operate the equipment.
The handset provided with this equipment is hearing aid compatible.
This equipment is not for connection to the telephone network or public coin
p
hone service. It is only for use when connected to Mitel systems.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING
T
EST CALLS TO EMERGENCY NUMBERS
• Remain on the line and briefly explain to t
he dispatcher the reason for the
call.
• Perform tests during off-peak hours such as
early morning or late evenings