AASTRA 6867I - User Manual
Table Of Contents
- Software License Agreement
- Welcome
- IP Phone Keys
- Getting Started
- Methods of Customizing Your Phone
- Phone Status
- Customizing Your Phone
- Line and Call Appearances
- Presence Key
- Configuring Softkeys
- State-Based Softkeys
- Softkey Display Behavior
- Line Key
- Speed Dial Key
- Speed Dial Prefix
- Press-and-Hold to Create a Speed Dial (applicable to softkeys, dialpad keys, expansion module keys)
- Creating a Speed Dial Key Using the Speed Dial Edit Option (applicable to softkeys, dialpad keys, expansion module keys)
- Creating a Speed Dial Softkey Using the Mitel Web UI
- Creating Dialpad Speed Dial Keys Using the Mitel Web UI
- Do Not Disturb (DND) Key
- Busy Lamp Field (BLF) Key
- BLF/List Key
- Automatic Call Distribution (ACD) Key (for Sylantro Call Managers)
- XML Key
- Flash Key
- Sprecode Key
- Park/Pickup Keys
- Last Call Return Key
- Call Forward Key
- BLF/Xfer
- Speed Dial/Xfer
- Speed Dial/Conf
- Speed Dial/MWI
- Directory Key
- Callers List Key
- Redial Key
- Conference Key
- Transfer Key
- Intercom Key
- Phone Lock Key
- Paging Key
- Discreet Ringing Key
- Empty Key
- None Key
- Making Calls
- Receiving Calls
- Handling Calls
- Managing Calls
- Additional Features
- Display DTMF Digits
- Play Call Waiting Tone
- Stuttered Dial Tone
- XML Beep Support
- Status Scroll Delay
- Switch UI Focus to Ringing Line
- Call Hold Reminder During Active Calls
- Call Hold Reminder (on single hold)
- Call Waiting Tone Period
- Preferred Line and Preferred Line Timeout
- Goodbye Key Cancels Incoming Calls
- Message Waiting Indicator
- Incoming Intercom Call Features
- Group RTP Paging
- Shared Call Appearance (SCA) Call Bridging
- BroadSoft BroadWorks Executive and Assistant Services
- Star Codes
- Other Features
- Model M680i and M685i Expansion Modules
- Troubleshooting Solutions
- Why is my display blank?
- Why is my speakerphone not working?
- Why can’t I get a dial tone?
- Why doesn’t my phone ring?
- Why is the light not coming on with a new voicemail message?
- Why is my handset not working?
- How do I find the IP address of my phone?
- Why does my phone display the No Service message?
- How do I change my user password?
- Why does my phone display Bad Encrypted Config?
- How do I restart the IP phone?
- How do I lock my phone?
- Limited Warranty
- Limited Warranty (Australia Only)
- Appendix A - Time Zone Codes
Mitel 6867i SIP Phone Release 4.1.0 SP3 User Guide
204
GROUP RTP PAGING
You can configure the phone to allow it to receive a Real Time Transport Protocol (RTP) stream
from pre-configured multicast address(es) without involving SIP signaling. This is called Group
Paging on the IP phones. You can specify up to 5 multicast addresses that the phone listens
for on the network. This feature is configurable using the Mitel Web UI only.
The 6867i in the local network listens for RTP on the pre-configured multicast address. The
Phone displays the Paging message to the phone’s LCD. It uses the G711 uLaw CODEC for
multicast RTP.
The recipient can drop the incoming page if required. The recipient can also set DND to ignore
any incoming pages.
For incoming RTP multicasts, the ringing display is dependent on the setting for the Allow
Barge In parameter (see “Allow Barge In” on page 202). If this parameter is disabled, and there
is no other call on the phone, then the paging is automatically played via the default audio device.
If there is an existing call on the phone, the call initially displays in the ringing state. The user
has the option to accept/ignore the call. If the Allow Barge In parameter is enabled, the RTP
multicast call barges in, and any existing calls are put on hold.
If an RTP multicast session already exists on the phone, and the phone receives another
incoming RTP multicast session, the priority is given to the first multicast session and the second
multicast session is ignored. The behavior for the incoming calls in this case is also based on
the setting for the Allow Barge In parameter. The incoming call is handled as if there were an
existing call already on the phone.
CONFIGURING GROUP RTP PAGING
1. Click on Basic Settings > Preferences > Group Paging RTP Settings.
2. In the Paging Listen Addresses text box, enter the multicast IP address(es) and port
number on which the phone listens for incoming multicast RTP packets.
Enter the IP address in dotted decimal format (for example,
239.0.1.15:10000,239.0.1.20:15000)
You can enter up to 5 listening multicast addresses.
If this field is blank, the paging listening capability is disabled on the phone.
3. Click Save Settings.
MITEL WEB UI
Notes:
1. Recipient of a paging call can set a global DND to ignore any incoming pages.
2. For incoming paging, the phone uses the Intercom configuration settings. The
incoming page is dependent on the Allow Barge In parameter setting and the
idling/on call state