Operation Manual

HiFi Audio System for iPad/iPhone
MODEL: MITSP30
(iPod/iPhone/iPad not included)
INSTRUCTION MANUAL
PLEASE READ THIS OPERATING MANUAL COMPLETELY
BEFORE OPERATING THIS UNIT AND RETAIN THIS
BOOKLET FOR FUTURE REFERENCE.
Table of Content Page No.
CONTENTS
GENERAL SAFETY INSTRUCTION
PRODUCT FEATURES
LOCATION OF CONTROLS
PREPARATION FOR USE
BASIC OPERATION
LISTENING TO YOUR iPod/iPhone/iPad
CHARGING YOUR iPod/iPhone /iPad
WATCH VIDEO FROM iPod Touch/ iPhone /iPad
TO LISTEN TO OTHER AUDIO DEVICE
TROUBLESHOOTING GUIDE
SPECIFICATIONS
1
2
3
4
6
7
7
7
7
8
8
10
6. The apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed near the product. Dry
location use only.
7. No naked flame sources, such as candles, should be placed on the product.
8. Keep the power cord and product away from heated surfaces.
9. Keep at least 5 cm of space around the unit for sufficient ventilation.
10. The ventilation holes should not be blocked up by things such as newspapers,
dusters, curtains, etc. Place the product where there is good air circulation.
11. Do not place or drop the product into water or other liquids. If the product falls
into water, immediately unplug it from the electrical outlet; do not pull on the
power cord.
12. Do not expose batteries to excessive heat, such as fire, direct sunlight, etc.
13. Dispose of used batteries in an environmental friendly way.
14. Do not place the unit near TV, speakers, and other objects that generate
strong magnetic fields.
15. Do not clean the unit with strong chemical agents.
16. This product has no user-serviceable parts. Do not attempt to dismantle or
repair this unit yourself. This unit should be repaired by qualified service
technician only.
17. Do not operate the unit if it is not working normally or has been damaged in
any way. Turn the unit off. Unplug it from the power source. And consult
service personnel.
18. Do not remove any fixed cover. This will increase the chance of electrical shock.
19. Press the player’s buttons gently. Pressing them or the screen too hard can
damage the player.
20. Do not push any objects into holes, slots, or openings on the unit. This could
result in fatal electric shock.
21. Do not subject the product to harsh impacts. Do not drop the appliance. This
may result in damage to the product and loss of data.
22. Care is required for the use of this apparatus in tropical and/ or moderate
climates.
23. Do not use the player in an extremely dry environment, as this can lead to
static discharge, which can damage the player.
24. Only use attachments/ accessories specified by the manufacturer.
25. Unplug this apparatus during lightning storms or when it is unused for long
periods of time.
26.The power supply as the on/off switch is easy for operation
PRODUCT FEATURES
This music system has an iPod Dock with following features:
Play and Charge your dockable iPod,iPhone or iPad.
3.5mm Auxiliary input for MP3 player connection.
Watch Video from iPod Touch/iPhone/iPad.
AC adaptor operation.
Remote control operation.
GENERAL SAFETY INSTRUCTION
READ ALL INSTRUCTIONS BEFORE USE
Congratulations on your purchase of this speaker system with iPod dock. To get
the most from your speaker system, please take a few minutes to read these
instructions.
NOTE: This unit is not magnetically shielded and may cause color distortion on
the screen of some TVs or video monitors. To avoid this, you may need to move
the unit further away from the TV or monitor if unnatural color shifts or image
distortion occurs.
WARNING - To reduce the risk of fire, electric shock or serious
personal injury. Do not open the unit. This product is intended for indoor,
non-industrial, non-commercial use; do not use the product outdoors.
Do not mount this product on a wall or ceiling.
1. Always follow basic safety precautions when using electrical products.
Children should be supervised to ensure that they do not play with appliances.
2. Do not allow children to operate the unit without adult supervision.
3. Read this instruction manual carefully before you attempt to use the unit.
4. Consult your dealer or service personnel if you have further questions about
the operation or safety of the unit.
5. Do not expose the product to temperatures above 40°C. Keep it in moderate
climates.
Always follow basic safety precautions when using electrical products,
especially when children are present.
Sound is
distorted.
Unit gets warm
after extended
play at high
volume.
Please make sure that your
iPod is working properly
before docking into the unit.
Please refer to your iPod
manual for info on resetting
the iPod.
Please make sure your
iPod is working properly
before docking into the unit.
Please refer to your iPod
manual for details on
resetting.
Your iPod is locked up.
iPod is locked up/ frozen.
iPod battery has problem.
Volume level is set too
high.
Sound source is distorted.
This is normal.
Decrease the volume.
If the iPod original sound
source is of poor quality,
distortion and noise are
easily noticed with
high-power speakers.
If you are using an external
sound source like older
generation of iPod, try
reducing the output volume
on the device itself.
Turn the unit off for a period
of time or lower volume.
SPECIFICATIONS
Main power: 100-240V AC 50/60Hz output: DC 16V 2000mA.
Main unit: DC input: DC 16V / 2000mA
Output power: 2 x 10W RMS
NOTE: AS A RESULT OF CONTINUAL IMPROVEMENTS, THE DESIGN AND SPECIFICATIONS
OF THE PRODUCT WITHIN MAY DIFFER SLIGHTLY TO THE UNIT ILLUSTRATED ON THE PACKING.
Power Requirement
BASIC OPERATION
LISTENING TO YOUR iPod/iPhone/iPad
1.) This system is equipped with a dock to allow you to connect your iPod/iPhone
/iPad to enjoy your favorite music via the speaker system. The system is able
to fit most types of currently available iPod/iPhone/iPad models with 30-pin
dock connector. This unit can also charge your iPod/iPhone/iPad when it is
connected well via the dock.
Note: Please be careful when seating the iPod into the docking to avoid
damaging the 30-pin connector on the iPod or in the docking system.
2.) Press the power button on the base or the remote control to turn on the unit.
The iPod will start playing automatically and start charging immediately.
3.) Adjust the sound level of the speaker system by pressing VOLUME +/-
buttons on the base or the remote conrtol.
Note: The volume level cannot be adjusted using the volume control on your
iPod after being docked.
CONNECTING iPod Touch OR iPhone TO YOUR SPEAKER SYSTEM
1. Plug the AC adaptor into DC power Jack at the back of the unit.
2. Press the button on the base or the remote control to switch on the speaker.
3. Press ‘Vol-/+’ on the base or the remote control to adjust volume level.
4. Press or button on the base or the remote control to skip to the next or
previous song; Press button on the base or the remote control to pause or
resume iPod playback.
5. Press ‘AUDIO’ on the base or press the ‘MODE’ button on the remote control
to change the mode.
6. If used with another audio source, connect audio devices with unit by 3.5mm
audio cable.
PREPARATION FOR USE
FRONT VIEW OF THE MAIN UNIT
REAR VIEW OF THE MAIN UNIT
17 18 19 20
7 9
1 2 3
4 5 6
11 12
8 10
13
14
16
15
1. AUDIO BUTTON 2. TUNE- BUTTON 3. PAUSE BUTTON 4. TUNE+ BUTTON
5. VOLUME- BUTTON 6. VOLUME+ BUTTON 7. AUX LIGHT 8. IPOD LIGHT
17. OUT-R 18. DC IN JACK 19. AUX JACK 20. OUT-L
9. CHARGE 10. POWER 11. LEFT SPEAKER 12. RIGHT SPEAKER
13. IPOD DOCK 14. IPOD DOCK BACK BUTTON 15. POWER BUTTON
16. REMOTO CONTROL WINDOW
2 3
109876
AUX IN CONNECTION
1. You can enjoy music from most portable music players by using this
speaker system. Connect the 3.5mm Aux-In cable to the AUX-IN jack and
the other end to the headphone or line-out jack of your preferred device.
Select the play function on the auxiliary device and the sound output can then
be heard from the unit. Disconnect the audio cable if you are not going to use
the aux in mode.
5
NOTE: This unit is not magnetically shielded and may cause color distortion
on the screen of some TVs or video monitors. To avoid this, you may need to
move the unit further away from the TV or monitor if unnatural color shifts or
image distortion occurs.
LOCATION OF CONTROLS
PREPARATION FOR USE
CONNECTING THE AC POWER ADAPTOR
Unpack the unit carefully. Carefully remove all the accessories from the display
carton. We recommend that you save the box and packing materials, in case you
wish to store the unit. Don’t remove any labels or sticker on the rear of the unit and
adaptor.
Before setting up the unit, verify that the following accessories are present:
This unit is supplied with an AC adaptor with the output DC 16V 2000mA; take
the following steps to connect the adaptor.
1. Unwind the power cord of the AC adaptor to its full length.
2. Firmly insert the DC plug of the AC adaptor to the DC socket on the rear of
the unit.
3. Plug the AC adaptor to the AC outlet (100-240V ~ 50/60 Hz). Connecting
this system to any other power source may cause damage to the system.
For sufficient ventilation, keep other objects at least 10cm away from the unit.
Remote control x 1
Connection wire x 2
4
TO LISTEN TO OTHER AUDIO DEVICE
Connect other audio device(MP3 players, CD players and older, non-dockable
iPod (except iPod shuffle 3 gen) to the line in jack at the back of the base by using
the special 3.5mm audio cable.
Press the power button to turn on the speaker, press the ‘AUDIO’ button to select
the mode. And listen to it.
Note:Press the power button to turn off the system when you finish listening.
Don't forget to switch off the power of your external device as well.
TROUBLESHOOTING GUIDE
Symptom Possible Problem Solution
If you experience any difficulties in operating this unit, please check the
following chart to see if you can fix it before consulting a servicing professional.
The unit does
not respond
(no power).
iPod does not
respond to the
speaker system.
Plug the AC adaptor into a
wall outlet and plug the
connector into the supply
jack on the unit.
-AC Adaptor is not
plugged into a wall outlet
-The connector is not
plugged into the power
supply jack on the back
of the unit.
Wall outlet is not
functioning.
iPod is not installed
properly.
Remove your iPod from the
dock and check for
obstruction on the
connectors and on your
iPod. Then reseat it on
the dock.
Plug another device into the
same outlet to confirm the
outlet is working.
When your iPod/iPhone/iPad docked to the unit, it will be recharged automatically.
During charging, the charge light will flashing, after charging full the charge light will
off automatically. Other non-docking types of iPod will not be charged.
In iPod mode, you can watch the video from your iPod Touch/iPhone/iPad
In AUX mode, you can watch the video through connecting you iPad use the
special 3.5mm audio cable.
WATCH VIDEO FROM iPod Touch/ iPhone /iPad
CHARGING YOUR iPod/iPhone/iPad
If at any time in the future you should need to dispose of this product please note that:
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice. (Waste Electrical and Electronic Equipment Directive)
www.capi.com
REMOTE CONTROL
1. Power ON / OFF Button
2. Function Select Button
3. iPod menu up button
4. iPod SKIP Previous /TUNE- button
5. iPod SKIP Next /TUNE+ button
6. iPod Play/Pause Button
7. iPod menu down Button
8. iPod menu Button
9. iPod menu enter Button
10. Volume Down Button
11. Volume Up Button
1 2
3
5
7
9
11
4
6
8
10
REPLACING THE BATTERY FOR THE REMOTE CONTROL
CAUTION: There is danger of explosion if battery is incorrectly
replaced. Replace the battery only with the same or equivalent type.
The remote control operates on one CR2025 battery (included). To extend the
life of the original battery, the factory has inserted a small clear plastic spacer
tab between the lithium battery and the battery terminal, to activate the remote
control, remove the insulation tab attached in the battery compartment.
When the operation of the remote control becomes
intermittent or unsatisfactory,
replace the original battery with a new 3-volt
lithium battery.
1.) Slide out the battery holder from the remote
control case.
2.) Replace the 3V CR2025 battery. Be sure the battery
is installed correctly.
The remote will not work if the battery is installed with the
wrong polarity.
CAUTION: Danger of explosion if the battery is replaced
incorrectly.
Replace only with the same type battery.
3.) Insert the battery holder into the battery slot.
NOTE: Use only the size and type of battery specified. If the device is
not to be used for a long period of time, remove the battery to prevent damage
or injury from possible battery leakage. Do not try to recharge the battery, it is
not intended to be recharged and doing so may cause the battery to rupture or
leak. Battery shall not be exposed to excessive heat such as direct sunlight,
fire or the like. Only use a well-known brand of cell battery to ensure the longest
life and best performance.