DIAMOND VIEW MONITORS A REGISTERED TRADE MARK OF MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD. 1554R Colour Monitor 15” (38.1cm) CRT Size, 13.9” (35.4cm) Max.
Table of Contents Safety Instructions for Display Monitors........................................................................................ii Maintenance................................................................................................................................................iii Chapter 1 Introduction ...................................................................................................................................... 1 Unpacking the Package.......................
Copyright Copyright © 2000 Mitsubish Electric Australia Pty. Ltd All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer Mitsubish Electric Australia Pty.
Safety Instructions for Display Monitors 1. The AC plug isolates this equipment from the AC Power supply. 2. Unplug the monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Slots and openings in the cabinet and the back or bottom are provided for ventilation. They must not be blocked or covered.
Maintenance ✘ Do not expose the monitor to direct sunlight or heat. ✘ Do not spill liquid onto the monitor. ✘ Do not attempt to open the monitor. You may be hurt by electric shock. For service, call your place of purchase. Opening your monitor may also void warranty. ✘ Do not use your monitor when magnets or electronic products are operating nearby. ✘ Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen. Wipe it with clean, soft clothes applied with mild solution.
Introduction Unpacking the Package 1 Check following items. If they are missing or damaged, consult your place of purchase immediately. 9 Colour monitor 9 Swivel base 9 User’s manual 9 Power cord Locate the model name and the serial number labeled on the back of your monitor. Write down the related information of your monitor and dealer in the space on page ii for future reference.
9 Power Saving Function The power management complies with VESA DPMS standard. When the system is idle (off mode), the monitor automatically cuts its power consumption up to 95%. 9 Green Commitment No CFCs are used in the manufacturing process of your monitor. It complies with the US government’s Energy Star standards and the rigorous standards of the Scandinavian countries.
Getting Started 2 Installing the Monitor This monitor is equipped with an autosensing power supply for voltage ranges 100~240V AC, 50~60Hz. To install the monitor : 1. Make sure that the system power is turned off. 2. Please refer to the instructions below to connect the signal cable through D-SUB . 3. Connect the power cord to the monitor and attach it to power source. 4. Turn on the computer and the monitor.
Connecting through D-SUB signal connector 1. Make sure that the system power is turned off. 2. Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer. ) To connect the monitor to an older type Apple Macintosh through a D-Sub cable, you need to use an Apple Macintosh signal adaptor to connect the video signal port of your computer to the monitor signal cable. Adaptors are available from Mitsubishi Electric Australia.
Adjusting the Monitor 3 Control Functions The monitor digital control functions are located on the front panel (see the illustration below). They are described in the following sections. 1. Power Switch Pincushion Horizontal Size 2. Adjust Vertical Center Contrast 3.
Select / Adjust Press the SELECT + or - button to cycle through the adjustment options to choose H-Phase, H-Size, V-Center, V-Size, Contrast, Brightness, Trapezoid, Pincushion and Rotation. And then press ADJUST + or - button to change the settings. Recall Recall all settings to factory defaults by pressing both function keys of SELECT ADJUST - . + and Timing Setting By making adjustments of your video card settings, you can set the timing and the refresh rate to your preferences.
Troubleshooting and Useful Hints 4 Troubleshooting Make sure that your monitor is properly installed if you encounter any trouble using this product (For hardware installation, see Chapter 2, Getting Started). If the problems persist, check this chapter for possible solutions. 9 There is no picture on the screen. Check: Video sync signal. The video sync signal from the graphics card must be as specified for the monitor. Power saving mode. Press any key and move the mouse to deactivate the mode.
Need More Help? If your problems remain after checking this manual, please contact your place of purchase or contact: Australia Visit the Mitsubishi Electric Australia web site at www.mitsubishi-electric.com.
Specifications Picture Tube Size Type Dot pitch Surface coating Maximum Viewable Size Power Supply (Universal) Input voltage Power consumption(Max.) Max. Resolution Horizontal Frequency Vertical Frequency Video Bandwidth Video Input Adjustable Timing User’s Control Regulatory Compliance Plug & Play Ambient Temperature Operating Storage Humidity Operating Storage Dimensions (W x H x D) Weight (net) 5 15” (38.1cm) diagonal FST 0.28mm AG, AS coating 13.9” (35.