Datasheet

15
The next level of industry
c
Output Specications
Relay output
Item
Output Specications
FX5U-32M FX5U-64M FX5U-80M
No. of output points 16 points 32 points 40 points
Connection type Removable terminal block (M3 screws)
Output type Relay
External power supply 30 V DC or less
240 V AC or less ("250 V AC or less" if not a CE, UL, cUL compliant item)
Max. load 2 A/point
The total load current per common terminal should be the following value.
• 4 output points/common terminal: 8 A or less
• 8 output points/common terminal: 8 A or less
Min. load 5 V DC, 2 mA (reference values)
Open circuit leakage current —
Response time OFF→ON Approx. 10 ms
ON→OFF Approx. 10 ms
Insulation of circuit Mechanical insulation
Indication of output operation LED is lit when output is on
Output circuit conguration
AC power supply
Load
Fuse
Y
DC power supply
Fuse
Y
COM
COM
Load
A number is entered in the
c
of [COM
c
].
Transistor output
Item
Output Specications
FX5U-32M FX5U-64M FX5U-80M
No. of output points 16 points 32 points 40 points
Connection type Removable terminal block (M3 screws)
Output type Transistor/sink output (FX5U-
c
MT/ES)
Transistor/source output (FX5U-
c
MT/ESS)
External power supply 5 to 30 V DC
Max. load 0.5 A/point
The total load current per common terminal should be the following value.
• 4 output points/common terminal: 0.8 A or less
• 8 output points/common terminal: 0.8 A or less
Open circuit leakage current 0.1 mA or less/30 V DC
Voltage drop
when ON
Y000 to Y003 1.0 V or less
Y004 and subsequent 1.5 V or less
Response
time
Y000 to Y003 2.5 μs or less/10 mA or more (5 to 24 V DC)
Y004 and subsequent 0.2 ms or less/200 mA or more (24 V DC)
Insulation of circuit Photo-coupler insulation
Indication of output operation LED is lit when output is on
Output circuit conguration
Sink output wiring Source output wiring
Load
Fuse
DC power supply
Y
COM
Load
Fuse
DC power supply
Y
+V
A number is entered in the
c
of [COM
c
]. A number is entered in the
c
of [+V
c
].
Built-in RS-485 communication
Item Specications
Transmission standards Conforms to RS-485/RS-422 specications
Data transmission speed Max. 115.2 kbps
Communication method Full duplex (FDX) / half duplex (HDX)
Maximum total extension distance 50 m (164' 0")
Protocol type MELSOFT connection
Non-protocol communication
MODBUS RTU
Inverter communication
Insulation method Not insulated
Terminal resistors Built-in (OPEN/110 Ω/330 Ω)
Terminal block used European-type terminal block
Built-in Ethernet communication
Item Specications
Data transmission speed 100M/10M (bps)
Communication mode Full duplex (FDX) / half duplex (HDX)
Transmission method Base band
Maximum segment length 100 m (328' 1")
Cascade
connection
10BASE-T Cascade connection max. 4 stages
[1
100BASE-TX Cascade connection max. 2 stages
[1
Protocol type MELSOFT connection
SLMP (3E frame)
Socket communication
Number of simultaneously open connections
allowed
8 connections
Insulation method Pulse transformer insulation
Interface RJ45 connector
Cable used
[2
For 10BASE-T connection Ethernet standard-compatible cable, category 3 or higher (STP cable)
For 100BASE-TX connection Ethernet standard-compatible cable, category 5 or higher (STP cable)
[ 1 : Number of stages that can be connected when a repeater hub is used. When a switching hub is used, check the specications
of the switching hub used.
[ 2 : A straight cable can be used. If a personal computer and CPU module are directly connected (simple connection), a cross cable
can be used.
c
Input Specications
24 V DC input (sink/source)
Item
Specications
FX5U-32M FX5U-64M FX5U-80M
No. of input points 16 points 32 points 40 points
Connection type Removable terminal block (M3 screws)
Input type Sink/source
Input signal voltage 24 V DC +20 %, -15%
Input signal current X000 to X017 5.3 mA/24 V DC
X020 and subsequent 4.0 mA/24 V DC
Input impedance X000 to X017 4.3 kΩ
X020 and subsequent 5.6 kΩ
ON input sensitivity
current
X000 to X017 3.5 mA or more
X20 and subsequent 3.0 mA or more
OFF input sensitivity current 1.5 mA or less
Input response
frequency
X000 to X005 200 kHz —
X006 to X017 10 kHz —
X000 to X007 — 200 kHz
X006 to X017 — 10 kHz
X020 and subsequent — 0.1±0.05 kHz
Pulse waveform Waveform
T1 T1
T2 T2
T1 (pulse width) T2 (rise/fall time)
X000 to X005 T1: 2.5 μs or more,
T2: 1.25 μs or more
—
X006 to X017 T1: 50 μs or more,
T2: 25 μs or more
—
X000 to X007 — T1: 2.5 μs or more,T2: 1.25 μs or more
X010 to X017 — T1: 50 μs or more,T2: 25 μs or more
Input response time
(H/W lter delay)
X000 to X005 ON: 2.5 μs or less,
OFF: 2.5 μs or less
—
X006 to X017 ON: 30 μs or less,
OFF: 50 μs or less
—
X000 to X007 — ON: 2.5 μs or less,OFF: 2.5 μs or less
X010 to X017 — ON: 30 μs or less,OFF: 50 μs or less
Input response time
(Digital lter setting value)
None, 10 μs, 50 μs, 0.1 ms, 0.2 ms, 0.4 ms, 0.6 ms, 1 ms, 5 ms, 10 ms, 20 ms, 70 ms
When using the product in an environment with much noise, set the digital lter.
Input signal format No-voltage contact input
Sink: NPN open collector transistor
Source: PNP open collector transistor
Input circuit conguration • When using service power supply
Sink input wiring Source input wiring
24V
N
L
100 to 240 V AC
Fuse
X
S/S
0V
Input impedance
24V
N
L
100 to 240 V AC
Fuse
X
S/S
0V
Input impedance
• When using external power supply
Sink input wiring Source input wiring
ecnadepmi tupnIecnadepmi tupnI
24V
N
L
100 to 240 V AC
Fuse
X
S/S
0V
24V
N
L
100 to 240 V AC
Fuse
X
S/S
0V
Analog output
Item Specications
Analog output points 1 points (1 channels)
Digital input Unsigned 12-bit binary
Analog output Voltage 0 to 10 V DC (external load resistance 2 k to 1 MΩ)
I/O characteristics,
Maximum resolution
Digital input value 0 to 4000
Maximum resolution 2.5 mV
Accuracy
(Accuracy in respect to
maximum analog
output value)
Ambient temperature
25±5°C (77±41°F)
Within ±0.5% (±20 digit
[1
)
Ambient temperature
0 to 55°C (32 to 131°F)
Within ±1.0% (±40 digit
[1
)
Conversion speed 30 μs (data refreshed every operation cycle)
Insulation method Between output
terminal and PLC
Not insulated
Occupied points 0 points (does not pertain to the max. No. of input/output
points of the PLC.)
Terminal block used European-type terminal block
[
1 : "Digit" refers to digital values.
Analog input
Item Specications
Analog input points 2 points (2 channels)
Analog input Voltage 0 to 10 V DC (input resistance 115.7 kΩ)
Digital output Unsigned 12-bit binary
I/O characteristics,
Maximum resolution
Digital output value 0 to 4000
Maximum resolution 2.5 mV
Accuracy
(Accuracy in respect to
maximum digitaloutput value)
Ambient temperature
25±5°C (77±41°F)
Within ±0.5% (±20 digit
[1
)
Ambient temperature
0 to 55°C (32 to 131°F)
Within ±1.0% (±40 digit
[1
)
Conversion speed 30 μs/channel (data refreshed every operation cycle)
Absolute maximum input -0.5 V, +15 V
Insulation method
Between input terminal and PLC Not insulated
Between input terminals Not insulated
Occupied points 0 points (does not pertain to the max. No. of input/output
points of the PLC.)
Terminal block used European-type terminal block
[
1 : "Digit" refers to digital values.