Wi-Fi INTERFACE MODEL MAC-568IF-E INSTALLATION GUIDE Intelligent control, no matter where you are.
Setting Information Indoor unit model name Indoor unit serial number Outdoor unit model name Outdoor unit serial number Wi-Fi interface MAC address (MAC) Wi-Fi interface serial number (ID) Wi-Fi interface PIN (PIN) Wi-Fi interface SSID (SSID) Wi-Fi interface KEY (KEY) System commissioning date Wi-Fi interface installation date Installer Contact Details Name Telephone Number Wi-Fi interface Minimum Requirements for Operation: • Router capable of WPA2-PSK(AES) encryption. 2.
Contents Safety Precautions Product Introduction Parts Connecting the Wi-Fi Interface Wi-Fi Interface: Setting Up Instructions LED Pattern Troubleshooting Specifications 3 7 8 8 10 13 14 15 About Wi-Fi Interface This Wi-Fi interface communicates the status information and controls the commands from the server by connecting to an indoor unit. Safety Precautions • Read all safety instructions before installation, setting up, or use of the Wi-Fi interface.
Warning (Improper handling may have serious consequences, including serious injury or death.) • Attach the electrical cover to the indoor unit securely. If the electrical cover of the indoor units is not attached securely, it could result in a fire or an electric shock due to dust, water, etc. • When installing the Wi-Fi interface, use appropriate protective equipment and tools for safety. Failure to do so could cause injury.
[Precautions for setting up, or use of the Wi-Fi interface] Warning (Improper handling may have serious consequences, including serious injury or death.) Be sure not to do. • Do not disassemble, modify, or repair by yourself (user). It can cause electric shock, fire, or injury.
[Precautions for installation, setting up, or use of the Wi-Fi interface] Caution (Improper handling may have consequences, including injury or damage to building.) Be sure not to do. • Do not mount the Wi-Fi interface where children can reach. It can cause injury. • Do not use the Wi-Fi interface near other wireless devices, microwaves, cordless phones, or facsimiles. It can cause malfunctions. • Do not step on unstable step stool to set up or clean the Wi-Fi interface.
Product Introduction No Item Description 1 MODE Button Selects modes. 2 RESET Button Resets the system and ALL settings. 3 ERR LED (Orange) Shows the network error state. 4 NET LED (Green) Shows the network state. 5 MODE LED (Orange) Shows the Access Point Mode state. 6 UNIT LED (Green) Shows the indoor unit state. 3 4 5 6 ERR NET MODE UNIT RESET MODE 2 1 (1) MODE Button WPS-Push • Hold down the MODE Button for 2 seconds to start WPS-Push Pairing.
Parts Interface unit (with connecting cable) Fixing screw for 3.5×16 mm Fixing screw for 4×16 mm Mounting cord clamp Fastener (for bundling the wires) Holder Clip Connecting the Wi-Fi Interface (For details about your heat pump, see the relevant installation manual) Before dismantling the indoor unit, turn the power off and make sure that the power has been disconnected from the complete system. Dismantle the indoor unit in accordance with the service manual to access the main control PCB.
When mounting on the outer side of the indoor unit 1 2 Holder Holder Mark for cable Interface unit Clip Insert the clip into place. into the holder Align Connecting cable until it clicks Insert the interface unit it clicks into place. into the holder until into Note: When inserting the interface unit the holder, align the cable of the interface unit with the mark for the cable on the holder . Otherwise, light leakage or degradation in appearance may result.
Wi-Fi Interface: Setting Up Instructions Information for users: The following steps explain how to connect the Wi-Fi interface to a Router. KEY (LED LIGHTS): 1 : ON : OFF 2 ERR NET MODE UNIT RESET : Flashing MODE Wi-Fi Control Ensure the Wi-Fi interface is connected correctly as per the previous section, ‘Connecting the Wi-Fi interface’. UNIT LED should be flashing green only.
5 Check the label on the back of the interface for the SSID. Open the Wi-Fi networks screen on your smartphone/ tablet and connect to the network with the same name as the SSID. The network password, labelled KEY, is just under the SSID on the interface. You will now be connected to this Wi-Fi interface. 7 6 Open Wi-Fi Control App and follow the ‘How to Setup’ instructions in the ‘Setup Wi-Fi interface’ section.
5 6 ERR NET MODE UNIT RESET Activate WPS on your Wi-Fi interface by using a small object to press and hold the MODE Button for 2 seconds. 7 RESET MODE When pairing process is completed on the Wi-Fi interface, the NET LED lights up solid green for 5 seconds. 9 Open Wi-Fi Control App. Enter MAC and ID into ‘Add new unit’ and select ‘Add’. 12 When WPS-Push is enabled on the Wi-Fi interface, MODE LED starts flashing orange (every second).
LED Pattern : ON : OFF : Flashing ● Software initialising Description ERR (Orange) NET (Green) MODE (Orange) UNIT (Green) (every second) (every second) NET (Green) MODE (Orange) UNIT (Green) (every 5 sec) (every 5 sec) Firmware updating Firmware downloading Reset to the factory default ● Wireless setting Description ERR (Orange) Access Point Mode activated WPS-PUSH Mode activated (every second) WPS-PIN Mode activated (every 0.
Troubleshooting : ON : OFF : Flashing Description ERR (Orange) NET (Green) MODE (Orange) UNIT (Green) Connection to server established, and connection to indoor unit failed Connection to Router failed, and connection to indoor unit established (*3) Connection to Router failed, and starting up indoor unit connection (*3) Connection to Router failed, and connection to indoor unit failed (*3) Connection to server failed, and connection to indoor unit established (*2) Connection to server failed
ter. ocal Specifications Input voltage DC12.7 V (from indoor unit) Power consumption MAX 2W Size H×W×D (mm) 79×44×18.5 Weight (g) 110g (including cable) Transmitter power level (MAX) 17.5 dBm @IEEE 802.11b RF channel 1ch ~ 13ch (2412~2472 MHz) Radio protocol IEEE 802.
Contact Details Mitsubishi Electric New Zealand Mitsubishi Electric Australia w w w. m i t s u b i s h i - e l e c t r i c . c o . n z / w i f i w w w. m i t s u b i s h i - e l e c t r i c . c o m . a u / w i f i WELLINGTON SYDNEY HEAD OFFICE HEAD OFFICE 1 Parliament Street PO Box 30772 Lower Hutt 5040 348 Victoria Road Rydalmere NSW 2116 Phone 0800 639 434 Fax (04) 560 9133 Phone 1300 728 119 Fax (02) 9898 0484 Helpline opening hours 8.30am - 5.