DIGITAL MONOCHROME PRINTER MODEL P93DW P93DE OPERATION MANUAL BRT BRT/CONT DOWN UP LOCK FEED COPY CONT LOCK OPEN THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 89/ 336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
FOR THE MODEL P91DW(UB) ONLY WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL2601-1 and CAN/CSA C22.2 No. 601.1. Case 1. Connect to the 120V receptacle of the room or the host equipment. The AC power cord should be UL or CSA approved and consist of type SJT, size 16 or 18AWG, length 2.5m or shorter cord with IEC320/C13 type, 125V 10A or higher rating connector and NEMA 5-15 type, 125V 10A or higher rating, Hospital Grade plug.
CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN. TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
WARNING: Install and use this appliance in accordance with the operation manual for safety and EMC (Electromagnetic Compatibility). If it is not installed and used in accordance with the operation manual, it may cause interference to other equipment and/or other risk. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. This appliance must be earthed. In Europe, use the AC power cord according to the recommendations as below, in order to comply with EN60601-1 and EN60950.
INSTRUCTIONS FOR MEDICAL USE MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the ACCOMPANYING DOCUMENTS. Portable and mobile RF communications equipment can affect MEDICAL ELECTRICAL EQUIPMENT.
Guidance and manufacturer's declaration - electromagnetic emissions The Model P93DW/P93DE is intended for use in the electromagnetic environment specified below. The customer or user of the Model P93DW/P93DE should assure that it is used in such an environment.
Guidance and manufacturer's declaration - electromagnetic immunity The Model P93DW/P93DE is intended for use in the electromagnetic environment specified below. The customer or user of the Model P93DW/P93DE should assure that it is used in such an environment.
Recommended separation distances between Portable and mobile RF communications equipment and the Model P93DW/P93DE The Model P93DW/P93DE is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled.
1 CONTENTS 1 CONTENTS ................................................................. 1 2 PRECAUTIONS ..................................................... 2 - 4 3 UNPACKING ................................................................ 5 4 FEATURES AND FUNCTIONS .............................. 6 - 7 Front Panel .......................................................................................... 6 Rear Panel .........................................................................................
2 PRECAUTIONS In the interest of safety, please observe the following precautions: POWER REQUIREMENT This digital monochrome printer is designed for operation on 100-240V AC 50/60Hz. Never connect to any outlet or power supply having a different voltage or frequency. WARNING : THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT : CET APPAREIL DOIT ETRE MIS A LA TERRE. This equipment is classified as class 1, according to the type of protection against electric shock.
FOR LONG OPERATING LIFE UNSUITABLE MATERIALS FOR THE UNIT Many plastic components are used in the unit. Coat flaking and deformation are likely to occur if the unit is wiped with chemical dusters, benzine, thinner or any other solvent, if rubber or PVC items are left in contact with the unit for extended duration, or if the unit is sprayed with insecticide. CARE OF THE CABINET Unplug and clean with a soft cloth slightly moistened with a mild soap and water solution. Allow to dry completely before operating.
SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device. Scope: a) Visual check Housing, cables, operator controls, readout device ( displays, LED etc.), labels, accessories, instruction manual. b) Function test Performance check acc. instruction manual, also unity and applicability of set and accessory test. c) Electrical check Safety electrical test of the configuration in accordance with EN60601-1.
3 UNPACKING Take the unit out of the box by the following procedures. Make sure to check the contents. 1 Open the top of the box. 3 Take the unit out of the box carefully. • Make sure to keep the unit horizontal. 2 Remove the cushion above the unit. 4 Unwrap the unit.
4 FEATURES AND FUNCTIONS Front Panel 1 2 3 4 5678 9 BRT/CONT DOWN BRT UP LOCK FEED COPY A CONT LOCK B 1 2 3 4 5 6 7 8 9 A B OPEN Function Name Power switch Turns on/off the power. Displays stand-by, functions and error messages. Indicator (BRT/CONT/LOCK) Displays the settings of brightness, contrast and button function lock BRT(brightness)/ Makes fine adjustments of the brightness and contrast of the print image.
Rear Panel C D 1 2 3 4 ON OFF USB DIP SW AC LINE E EQUALIZATION F POTENTIAL TERMINAL DIP SW FUNCTION TABLE NO. FUNCTION SW-ON SW-OFF 1 2 3 4 LOCK ON OFF This is used to equalize the potential of the equipment connected to this unit. For details refer to the installation instruction of equipment to be connected. C D E F Function Name DIP switch Selects special functions. USB terminal Connects to the device equipped with USB interface such as personal computer.
5 INSTALLATION OF PAPER 3 Pull out the paper end. Moisture, fingerprints or dust on the paper surface may cause a noise at printing or deterioration in print quality. Set the paper by the following procedure to prevent adhesion of fingerprint or dust on the paper surface. • Pull out the first 1520cm (6 in. - 9 in.) of the paper to remove any slack in the roll. 1 Open the door. 4 Close the door. • Switch the lever located on the left side to the “OPEN” position. OPEN The door opens.
When setting the paper, observe the following precautions to prevent paper jam. Do not use defective paper. Do not use bent or wrinkled paper. Adjust the paper position correctly. When the paper is fed out skewed from the print exit, adjust the paper position so that it is fed out straight. Do not allow slack in the paper roll. Set the paper tightly to remove any slack. If the side of the print paper is uneven or the core is sticking out, the amount of paper feeding after printing may vary.
6 EXAMPLE OF CONNECTION / SETTING OF SWITCHES Connecting to various equipment with USB interface such as medical equipment and personal computer. Connection Connect the digital monochrome printer with PC or medical equipment through a USB cable. Personal computer or medical equipment To USB terminal ON OFF USB AC LINE Connect Power cord Rear panel Setting of Switches Set the DIP switches on the rear panel. • When setting the switch No. 1 to ON, DOWN, UP, and LOCK buttons ON will be locked.
7 PRINTING 1 Turn on the power. 3 Cut the printed paper. • Press the POWER switch to turn on the power. cutter 2 • Cut the printed paper with the cutter by tearing off the paper in the upper right direction. • Do not pull the paper in the horizontal direction. The paper inside the unit may be displaced and printing may not be carried out correctly. Print a picture displayed on the screen. Print a picture with an application software. The image data is transferred through USB interface.
Paper Feeding 2 FEED To feed the paper, press the FEED button on the front panel. Precautions on Printing When dark pictures are printed consecutively, the digital monochrome printer may become overheated and the indicator blinks. In this case, wait for a while until the unit has cooled down. Avoid pulling out or holding the paper during printing or copying to prevent paper jam. Do not touch the paper until printing or copying finishes.
8 ADJUSTMENT OF PRINT PICTURE Adjustment of Printer Brightness/Printer Contrast You can make fine adjustment of printer brightness and printer contrast of the printed picture. Control panel BRT/CONT DOWN BRT UP LOCK FEED COPY CONT LOCK • For adjustment, use the BRT/CONT button " BRT/CONT ", UP button " UP " and DOWN button " DOWN 1 Press the BRT/CONT button. BRT BRT/CONT DOWN UP LOCK FEED Press the BRT/CONT button " COPY CONT BRT/CONT " LOCK once to adjust the printer brightness.
2 Change the setting. UP DOWN 3 Store the set value. By pressing the BRT/CONT button again, the setting value is memorized. The memorized value will not be lost even when the power is turned off. • Press the UP button to increase the value. • Press the DOWN button to decrease the value. The setting value is displayed by the indicator. (example) Setting range is -19 to +19.
Automatic restoration to the standby status from the adjustment or setting mode When left without any operation of buttons, and switches under the following conditions for more than 20 seconds, this unit automatically returns to the standby status (Indicator display : ). In this case, the newly set value is not memorized and the setting goes back to the value that was set before change.
9 ERROR DISPLAY In case of an error in the unit during operation, you are warned by an alarm tone or the LED indicator. Cause/Error display 1 Overheat Symptom/Remedy [Symptom] • When the head gets overheated, the indicator blinks. When overheat occurs while more than one copy is being processed, printing starts as soon as the error is solved. If some images are waiting to be processed, the following buttons function as described below.
Cause/Error display 2 No paper Symptom/Remedy [Symptom] • When the paper runs out or the paper is not installed, printing becomes impossible and an alarm tone is heard. In this case, all the buttons become invalid. • If this error occurs while more than one copy is being printed or there are images waiting to be processed, printing is cancelled at the occurrence of the error. [Remedy] Install a new roll of paper according to "5. INSTALLATION OF PAPER" on page 8.
Cause/Error display 4 Door error Symptom/Remedy [Symptom] • When the door opens, an alarm tone is heard. The indicator displays " " for one second. In this case, all the buttons and switches become invalid. • If this error occurs while more than one copy is being printed, printing is cancelled at the occurrence of the error. [Remedy] Close the door. When the door is closed while the printing of more than one copy is being printed, an alarm tone is heard.
10 STATUS AND MODES Set state/Mode Contents of LED display LED display Power off Power off Stand-by During data receiving During data receiving Print state Remaining number of copies / number of copies 1 to 99 100 to 199 200 Continuous copy printing Printer brightness mode Fine adjustment of the picture brightness Printer contrast mode Fine adjustment of the picture contrast Error detect state No paper Button input error Door is open.
11 USE OF CLEANING PAPER When the thermal head is dirty with dust, etc., white spots or stripes may appear on the print. In this case, clean the thermal head by the following procedure BY USING THE SUPPLIED CLEANING PAPER. 1 4 Turn on the power. Close the door. Press the POWER switch to turn on the power. 2 Open the door. OPEN 3 Close the door without taking out the cleaning paper. Switch the left side lever to the OPEN position. The door opens. 5 Press the FEED button.
12 MAINTENANCE Turn off the power for maintenance. Maintenance of Main Unit Wipe off stains of the front panel with a soft cloth. When the panel is heavily stained, wipe with a cloth moistened with neutral cleanser diluted by water and finish with a dry cloth. Maintenance of Rubber Roller When the rubber roller is dirty with dust, etc., a blank spot may appear on the print. In this case, eliminate the dust on to the rubber roller with a blower or a brush. The regular cleaning using a lint-free cloth, etc.
13 SPECIFICATIONS Type: Digital Monochrome Printer Model: P93DW/P93DE Power supply and power consumption: 100-240V AC, 50/60Hz, 1.5 - 0.8A Connection terminal: USB interface (Series "B" receptacle) Hi-Speed USB (Ver. 2.0) supported Resolution: 1280 x 1280 pixels (Standard) (Max. 1280 x 5760 pixels) Gradation: 256 gradations Printing speed: 5.0 sec (Standard) Print size: 4" x 4" (100 mm x 100 mm) (Standard) (Max. 4" x 17.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road, Irvine, CA 92618 Phone 949-465-6000 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (0) 1707 276100 FAX (0) 1707 278755 German Branch Gothaer Strasse 8, 40880 Ratingen ; Postfach 1548, 40835 Ratingen ; Germany Phone 02102/ 486-9250 FAX 02102/ 486-7320 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.