CCD COLOR CAMERA BDC4803H USER MANUAL Page : 1
CONTENTS CONTENTSbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb - PRECAUTIONS……………………………………… Page 3 - PACKING CONTENTS...…………………………… Page 4 - 1. User Manual…………………………….............……… Page 4 - 2. Camera…………………..................…………………… Page 4 - 3. CS-Mount Adapter……………………………………… Page 4 - 4. Auto Iris Lens Connector……………...……………… Page 4 - FEATURES AND FUNCTIONS………………….… Page 5 - INSTALLATION…………………………………...… Page 6 - 1. Power connection…………………………………….… Page 6 - 2. Video cable……………………………………………..
PRECAUTIONS 1. Do not attempt to disassemble the camera. There are no user serviceable parts inside. Ask a qualified service person for servicing 2. Handle the camera with care. Do not misshandle the camera. Avoid striking, shaking, etc. Improper handling or storage could damage the camera. 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera. 4.
PACKING CONTENTS CONTENTS PACKING 1. User Manual 2. Camera 3. CS-Mount Adapter 4.
FEATURES AND FUNCTIONS F - Auto Light Control (ALC) function - Electronic Light Control (ELC) function - Automatic Gain Control (AGC) function - Automatic Tracing White Balance (ATW) function - Internal Synchronisation - Minimum Illumination of 1 Lux @ F2.0 - Signal to noise ratio > 45 dB (AGC off) - Horizontal resolution of 480 TV lines. - Auto Iris Lens Control selectable between video signal – and DC power controlled.
INSTALLATION I 1. Power connection Connect the DC 12V powercable with the DC 12V Terminal. DC 12 V (± 10%) Power connector camera rear side l Resistance of copper wire (at 20 °C) Copper wire size W/m 0,22 mm² 0,33 mm² 0,52 mm² 0,83 mm² 0,078 0,05 0,03 0,018 l Calculation of max.
2. Video cable l It is recommended to use a monitor with a resolution at least equal to that of the camera. Camera rear side l The max. extensible coaxial cable length between camera and the monitor is shown below. Coax cable type Recommended max.
3. Installation of the Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. The pin assignment of the lens connector is as follows: Signal for video iris lens : Pin 1: Power Source + 9V DC, 50mA max.
4. Mounting the Lens Camera description 1. Set up the lens by turning it clockwise on the lens mount of the camera. In case you are using a CS-Mount Lens connect the CS-Mount Adapter to the lens first and then mount it to the camera body. 2. Connect the lens cable to the Auto Iris Lens Connector on the side of the camera. 3. Adjust the Auto Iris Lens Selection Switch on the back (see page: 7) according to the used lens: To Video (V/D) for video controlled iris lens or DC for DC controlled iris lens. 4.
5. Operating controls and functions Function switch on the back (see page: 7) S/W 1 2 3 4 Function BLC ALC --AGC ON ON E/S --MIN OFF OFF ALC --MAX S/W 1 Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode according to the position of the object and light conditions on the screen. S/W 2 Automatic Light Control / Electronic Light Control Selector (ALC; E/S) Lets you select the mode according to the lens type used.
SSPECIFICATION Model Name Signal Standard Objective Mount CCD – Chip Scanning System Scanning Frequency Total Pixels Effective Pixels Horizontal Resolution Electronic Shutter S/N Ratio Sensitivity Sync System Automatic Iris Control White Balance Function Video Output Power Source Power Consumption Operating Temperature Operating Humidity Dimensions (W x H x D mm) (without connector) Weight (without Lens) Approvals BDC4803H PAL C-Mount and CS-Mount (adapter) 1/3” Super HAD CCD 2:1 Interlaced H: 15.
ADDRESS (Technical specifications subject to change. No liability will be assumed for printing errors or other errors.
