COLOUR VIDEO COPY PROCESSOR MODEL CP700E OPERATION MANUAL CP700 MONITOR MEMORY PRINT POWER OPEN REMOTE THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR COLOUR VIDEO COPY PROCESSOR. This video copy processor complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
1. Contents 1 Contents 1. Contents................................................................................................................. 1 2. Precautions ......................................................................................................... 2-4 3. Preparations before operation .......................................................................... 5-13 4. Connection with external equipment ............................................................... 14-21 5.
2. Precautions In the interest of safety, please observe the following precautions: POWER REQUIREMENT This Colour Video Copy Processor is designed for operation on 220-240V, 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency. WARNING: THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE. PROTECTIVE MEASURES IF ABNORMALITIES ARISE, .....
2. Precautions BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury. Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the provided power cord and the composite video signal cable. When connecting the unit with an equipment with RS-232C interface, use the RS-232C cross-over cable.
2. Precautions CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices. SAFETY CHECKS Periods: Scope: According to the recommendations of the manufacturer of the medical device. a) Visual inspection Housing, leads, controls, displays, labels/ markings, accessories, operation manual.
3. Preparations before operation 1 Removing the fixed screw on the printing unit and protective cushion Pages 5 - 6 2 Installing the lithium battery Page 6 ,Power for memorizing the day and present time are supplied by a lithium battery. Before using this unit install the lithium battery. 3 Installing the print paper and ink cassette. Pages 7 - 9 , Install the print paper. , Install the cassette with ink sheet.
3. Preparations before operation 1 Remove the protective cushion. Note: Unplug the power cord from outlet for safety. 1 Press the OPEN button on the front panel. Printing unit will slide out. Attention} } , Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality. 2 Pull out the protective cushion from the right side. Attention} } Protective cushion , Keep the protective cushion for transporting this unit.
3. Preparations before operation 3 Installing print paper and ink sheet 1 Installation procedure of print paper 1 Move the knob on the printing unit to the direction indicated by the arrow. 2 Insert the print paper in the position as shown below. Place the gear to the right side. Right side Print paper Folder Folder Left side Print paper Insert • Set the paper roll first on the right side paper holder. • Set the paper roll on the left side paper holder.
3. Preparations before operation 1 Install the ink sheet Install the ink sheet to the ink cassette before installing the sheet cassette to the unit. White roller 1 Set the black roller of the ink sheet to ink cassette as shown right A, B. E 2 Set the thin stick of white roller to the ink cassette as shown right C. B C A 3 Set the thick stick of white roller of the ink cassette as shown right D, E.
3. Preparations before operation 1 Print paper and ink sheet Attention} } , The following types of paper sheet sets are available. Use our original consumable. We can not guarantee the failure of using others.
3. Preparations before operation Menu display When setting the day and present time , use the menu on the LCD display. Also use the menu when selecting each setting after connecting an external device or selecting the print size (S /L). , There are 2 menus, Main menu and Memory SW menu. , Each menu is displayed as shown below. MAIN MENU Memory SW menu POWER Press the menu button to display the Main menu after pressing POWER button.
3. Preparations before operation 4 Setting the present time 1 Setting the day and present time Set the day and present time on the lower part of the print by the following procedure. , Set the day and present time in the menu on the monitor display or LCD display. A . Display “Memory SW Main Menu” , Make sure to turn off power. 1 Press the POWER button while pressing the MEMORY button. Menu display for button function “Memory SW Main Menu” is displayed. Memory SW Main Menu 1.
3. Preparations before operation 5 Press the UP button or DOWN 6 Press the RIGHT button to change the value. button. The month is set and display the “YEAR”. , The “YEAR” is displayed on the LCD . 7 Press the UP button or DOWN Time Adj Menu MONTH : 08 Time Adj Menu YEAR : 95 button to change value. Time Adj Menu YEAR : 99 8 Press the RIGHT button. , The day is set and the present time is displayed. Time Adj Menu HOUR : 00 The “HOUR” is displayed on the LCD .
3. Preparations before operation SET E Press the SET button. SET , When pressing the SET button, the present time function will be started. Time Adj Menu SECOND: 31 SET F Press the SET button. Memory SW Main Menu 1.TIME ADJ :PUSH[>] , “Memory SW Main Menu” display is shown. SET G Press the SET button. Memory SW Main Menu CHANGE: OK “CHANGE : OK” is selected. , Press the RIGHT or LEFT button to select “OK” or “CANCEL” according to the setting.
4. Connection with external equipment The functions of this unit can be set with the menu screens displayed on the monitor. 1 Connection with Monitors Pages 14 - 16 Explains how to connect with a monitor. Explains the setting of sync. polarity. , When the sync. polarity of a monitor differs from the initial setting of this unit, the image on the monitor may not be displayed correctly. In this case, set the sync. polarity according to the monitor.
4. Connection with external equipment (Monitor) Setting the sync. polarity and output sync. signal When the sync. polarity or sync. signal of a monitor to be connected is not adjusted to the initial setting of this unit, the image may not be displayed correctly. In this case, adjust the sync. polarity and sync. signal output to the monitor. When the image is displayed correctly, the setting is not required. (Refer to the operation manual of the monitor as for the sync. polarity and sync.
4. Connection with external equipment (Monitor) Setting the output sync. signal “OUTPUT SYNC” 5 Press the DOWN or UP button to select “OUT SYNC”. , The set level of the sync. signal, for example, “0.3V” is displayed. Signal Adj Menu OUT SYNC:TTL Set the sync. signal according to the equipment to be connected. or LEFT Press the RIGHT button to select “0.3V” or “TTL”. 0.3V ...... 0.3Vp-p TTL ....
4. Connection with external equipment (VIDEO/S-VIDEO) 2 Connection with VIDEO signal, S-VIDEO (Y/C separate VIDEO) signal equipment When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. VIDEO signal To VIDEO IN terminal VIDEO ( ) 1 RS-232C 2 REMOTE VIDEO S-VIDEO AC LINE IMPEDANCE ,, ,, CCD COLOR VIDEO CAMERA CCD-200E R G/G+SYNC B H+V-SYNC IN RGB 75Ω HIGH SYNC.
4. Connection with external equipment (RGB Analog signal) 3 Connection with RGB Analog Signal equipment , When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. RGB Analog signal equipment H+V-SYNC. B R G/G+SYNC. To RGB Analog IN terminal ( ) In case of SYNC ON G. signal, it is not necessary to connect to the unit.
4. Connection with external equipment (RS-232C Interface) 4 Connection with RS-232C equipment , When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. To RS-232C port (RS-232C) To RS-232C port 1 RS-232C 2 REMOTE VIDEO S-VIDEO AC LINE IMPEDANCE R G/G+SYNC B H+V-SYNC IN RGB 75Ω HIGH SYNC. 75Ω OUT HIGH R G/G+SYNC B H+V-SYNC Equipment with RS-232C VCP Setting BAUD RATE Set the baud rate of this unit according to the equipment to be connected.
4. Connection with external equipment (RS-232C Interface) Setting BAUD RATE 1 Press the DOWN or UP shift buttons to select “BAUD RATE”. The set baud rate, for example, “9600” , is displayed. Press the RIGHT or LEFT System Set Menu BAUD RATE : 9600 SHIFT button to select “1200” , “2400” , “4800” or “9600” Bit/Sec) . SET 2 Press the SET button. System Set Menu CHANGE : OK , “CHANGE : OK” is selected. , Press the RIGHT or LEFT shift button to select “OK” or “CANCEL” .
4. Connection with external equipment (RS-232C Interface) SET 4 Press the SET button. , “CHANGE : OK” is selected. SET 5 Select “OK”, then, press the SET button. , The source image (input signal from the equipment connected) is displayed. 0 The setting of COMMAND TYPE is completed. RS-232C DATA SIGNAL RS-232C input connector port signal allocation Pin No.
5. Features and functions 1 FRONT PANEL pages 22 - 23 Explains the buttons and terminals, etc. on the front panel. 2 INSIDE OF PRINTING UNIT page 23 Explains the installation of the ink cassette, print paper and battery inside the unit. 3 REAR PANEL page 24 Explains input/output terminals on the rear panel. 4 REMOTE CONTROL pages 25 - 26 Explains the functions of the buttons on the remote control.
5. Features and Functions 6 Memory button [MEMORY] This enables memorization of the image to be printed. 7 Print button [PRINT] Press this button to print the images memorized by the MEMORY button. A green lamp will light during printing. The screen switches to the picture of the input signal. 8 Open button [OPEN] When this button is pressed, the printing unit will slide out. The printing unit is used when loading ink cassette and printing paper or overcoming paper jams.
5. Features and Functions 3 REAR PANEL 1 RS-232C 2 REMOTE VIDEO S-VIDEO AC LINE IMPEDANCE R G/G+SYNC B Potential equalization connector RGB 75Ω H+V-SYNC IN This is used to equalize the potential of the equipment connected to the unit. For details, refer to the installation instruction of the equipment to be connected. HIGH SYNC. 75Ω OUT HIGH R G/G+SYNC B H+V-SYNC 1 S-VIDEO SIGNAL INPUT/OUTPUT TERMINALS [S-VIDEO] Use these terminals to connect this unit to S-VIDEO signal equipment.
5. Features and Functions 4 REMOTE CONTROL DISPLAY COLOR ADJUST PROG. FIELD /FRAME + PRINT Q' ty SET MENU CLEAR STOP MEMORY PAGE MONITOR MEMORY PRINT 1 COLOR IMAGE ADJUSTMENT button [COLOR ADJUST] When this button is pressed, a screen for adjusting the video image is displayed. Use this button to set the various functions of this unit. (The menus displayed on the monitor or LCD is used to set the various settings. Refer to Pages 45 - 46.
5. Features and Functions 8 PRINT button [PRINT] Press this button to print the image memorized by the MEMORY button. The image on the monitor screen is switched to the picture of the input signal. 9 PROGRAM button [PROG.] Press this button to select the images memorized in the program of this unit and various settings such as printing. Each time this button is pressed, the program is switched. This unit has 3 kind of programs and they can be changed and stored voluntarily.
6. Printing procedures (Basic prints) One picture image can be printed on one sheet. { S size printing 1 Printing { L size printing Pages 28 - 34 Explains storing an image in the memory and printing 2 Continuous printing Pages 35 - 36 Explains the continuous printing of the same image.
6. Printing Procedures (Basic prints) 1 Printing 1 Selecting FIELD or FRAME 1 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. DISPLAY PROG. COLOR ADJUST FIELD /FRAME + PRINT Q' ty MENU FIELD/FRAME button SET CLEAR STOP , Select the FRAME mode for a high resolution still image printing. Select the FIELD mode for a picture of quickly moving objects. , When the FIELD mode is selected, the print image will be lower in Normal Page:A PRG.
6. Printing Procedures (Basic prints) 1 Selecting input signal , Select “VIDEO” , “S-VIDEO” or “RGB” according to the input signal. , The input signal can be set on the menu screen displayed on the monitor or LCD. , It is not necessary to select the input signal everytime you print unless the input signal is changed. MENU 1 Press the MENU , “MAIN button. Main Menu 1.COLOR ADJ :PUSH[>] MENU” is displayed. 2 Press the DOWN or UP button to select “2. SIGNAL SET [ ] ]” . 3 Press the RIGHT button.
6. Printing Procedures (Basic prints) SET 5 Press the SET button . , “CHANGE : OK” is selected. , When changing the input signal selected at step 4, press the RIGHT Signal Set Menu CHANGE : OK SET button to select “CANCEL” . Press the SET button to select “INPUT” in “2. SIGNAL SET” again. SET 6 Press the SET button. Main Menu 2.SIGNAL SET:PUSH[>] , The MAIN MENU is displayed. SET 7 Press the SET button. , “SAVE PRG 1/2/3” is selected.
6. Printing Procedures (Basic prints) 1 Setting print size (S/L) , Set the print size to “S” or “L” according to the ink sheet installed. , The print size can be set on the menu screen displayed on the monitor or LCD. , It is not necessary to set the size everytime you print unless the size of the ink sheet is changed. 1 Press the MENU button. , “MAIN MENU” is displayed. 2 Press the UP Main Menu 2.SIGNAL SET:PUSH[>] button to select “4. PRINT PUSH [ ] ]” or DOWN . 3 Press the RIGHT Main Menu 4.
6. Printing Procedures (Basic prints) SET 5 Press the SET button. Print Menu CHANGE : OK , “CHANGE : OK” is selected. , When changing the size setting selected at step 4 , press the RIGHT SET button to select “CANCEL” . Press the SET button to select “MODE : S/L” in “4.PRINT” again. SET 6 Press the SET button. Main Menu 4.PRINT , The MAIN MENU is displayed. :PUSH[>] SET 7 Press the SET button. , “SAVE PRG 1/2/3” is selected.
6. Printing Procedures (Basic prints) 1 MEMORY PAGE The following image memorization function is available since this unit has 2 frames to memorize images. When storing one image in the memory: , In the frame mode, 2 images can be memorized in 2 frames. Image A Image B 1 frame + 1 frame = 2 frames , In the field mode, 4 images can be memorized in 2 frames.
6. Printing Procedures (Basic prints) , The page to store an image can be selected by pressing the MEMORY PAGE button. The page being selected is shown in green. , The image will be stored in the selected memory page when pressing the MEMORY button. (when memory page increment is set to OFF) , When pressing the MONITOR button, the image of the memory page being selected is displayed on the monitor. When the memorized image is displayed, “MEMORY” is displayed on the upper part of the monitor screen.
6. Printing Procedures (Basic prints) 2 Continuous printing The desired number of memorized images can be printed continuously when the desired number is set before printing. The number of prints can be changed during printing. The continuous printing also can be cancelled by setting the number of prints to 1 during printing. 1 Setting the number of prints Press the PRINT Q'TY buttons , Press , to set the number of prints. button to increase and button to decrease the number.
6. Printing Procedures (Basic prints) 1 Changing the number of prints during printing , When changing the number of prints during printing: 1 Press the PRINT Q'ty buttons , to set the number of prints to 1. 2 After the image being printed is printed out, press the PRINT Q’ty buttons , to change the number of prints. Note : 0 If blackish image is continuously printed, the internal temperature may rise and cause the unit to switch to a stand-by condition during printing.
7. Setting the functions 1 1 2 1 fi fi MAIN MENU is used to open the sub menu. Setting the following with the sub menu. When selecting "SAVE PRG", the setting can be stored. Main Menu PRG. 1.COLOR ADJ : PUSH [ 2.SIGNAL SET : PUSH [ 3.ADDITIONAL : PUSH [ 4.PRINT : PUSH [ 5.COMMENT : PUSH [ 6.SYSTEM : PUSH [ SAVE PRG : 1 / 2 / 3 ] ] ] ] ] ] 1. COLOR ADJ .................. Adjust color of printing image 2. SIGNAL SET .................
7. Setting the functions Operation Monitor display 3.ADDITIONAL STOROBE : OFF/1/15 sec MULTI : OFF/ON MODE : SAME/DIFF/PHOTO IMAGES : 2/4/16 SEPARATE : OFF/ON CHANGE ■ The menu is selected by pressing . : OK/CANCEL ■ Changing a value, selecting mode, switching ON or OFF is switched by pressing p . is reference page. p42 Image adjustment display 1.
7. Setting the functions p11 Day and present time setting display 1.TIME ADJ 28-02-99 19:45:00 SET p43 SET Analog image adjustment display p 57 ANALOG ADJ BRT : 0 -------------------------CONT : 0 -------------------------R-SUB : 0 -------------------------B-SUB : 0 -------------------------COLOR : 0 -------------------------SET CENTER :ON/OFF Button function setting display 2.
7. Setting the functions Operation LCD display Color Adj Menu BRT : 0 CONT : 0 R-SUB : 0 B-SUB : 0 CENTER : OFF ON ANALOG ADJ : PUSH [ ] CHANGE : OK CANCEL 1 The menus in the broken line are indicated by the shift buttons. ] 1 Press the shift buttons to change the value, select the mode or switch the item. (The item indicated by switching is shown in light character in this chart.) p p45 SET POWER is reference page.
7.
7. Setting the functions 1 Displaying menu screen , All functions are operated with the remote control. 1 Main menu – sub menu display MENU , Press the MENU button to display Main menu. 2 MEMORY SW MENU – sub menu display , Press the POWER button while pressing MEMORY button to display MEMORY SW menu. , Make sure to turn the POWER OFF before the above operation. 1 Displaying the sub menu , Select the sub menu for each function setting to display from MEMORY SW MENU or MAIN MENU.
7. Setting the functions SET 3 Press the SET button. , “CHANGE : OK/CANCEL” is selected. Key Setting Menu CHANGE :OK , Select "OK" to close the menu. Select "CANCEL" to cancel the setting again by the RIGHT or LEFT button. SET 4 Press the SET button. , The function is set and the Main menu display or Memory SW menu is shown. Memory SW Main Menu 2.KEY SET :PUSH[>] SET 5 Press the SET button. , In the Main menu, “SAVE PRG 1/2/3” is selected.
7. Setting the functions (Main menu) Function 1 MAIN MENU Open the sub-menu from Memory menu. e.g. Monitor display 1. COLOR ADJ → BRT 1 Items and setting displayed are shown below. 1. COLOR ADJ .......... Adjust color of printing image 2. SIGNAL SET .......... Selecting the input signal, reverse of odd and even field lines, filter,etc. 3. ADDITIONAL .......... Setting the number of images in a print. strobe print, photo print 4. PRINT.......................
7. Setting the functions (Main menu) 1 COLOR ADJ Adjusting the color of the image , With this menu, the color of the source image and memorized image can be adjusted. COLOR ADJUST , This menu is also displayed by pressing color ADJUST button. BRT (Bright ) Function Adjust the brightness of printing image.
7. Setting the functions (Main menu) ANALOG ADJ The adjustment image of analog input signal display , This menu is used to adjust the image of analog input signal display before storing in the memory. , This menu is opened when pressing RIGHT button on “ANALOG ADJ : PUSH [ ] ]” . , When selecting RGB analog signal, “COLOR” “TINT” is not adjusted and displayed. BRT (Bright ) Adjust the brightness of printing image. Function CONT (Contrast ) Function Adjust the contrast of printing image.
7. Setting the functions (Main menu) 2 SIGNAL SET Signal selecting menu INPUT Function Select the signal from inputting signal on the rear panel. VIDEO .......... Signal from VIDEO input terminal S -VIDEO ..... Signal from S-VIDEO input terminal RGB ............. Signal from RGB input terminal FIELD Function The odd even field lines will be reversed depending on the input interlaced signal.
7. Setting the functions (Main menu) 3 ADDITIONAL Special print setting STROBE Function This function is to repeat storing the image in the memory according to selected the time interval. When MULTI is set to “ON” , the image is stored in order of image number . When MULTI is set to “OFF” , every one image is stored in the memory. • The image is stored in the memory every time as shown below. , , 1/13 sec → 1/5 sec → 1/2.5 sec → 1 sec → 2 sec → 5 sec → 10 sec → 30 sec ............
7. Setting the functions (Main menu) SEPARATE Function Switching the white frame Separate the each image in multi-image print with white frame ON ................ White frame print OFF .............. Normal print • When “MULTI” is set to “ON”, this function is displayed. 4 PRINT Print setting 1 MODE Function Selecting the paper size Selecting the paper size depending on the installed the ink sheet. S ................... S-size ink-sheet ( model: PK700S) L ...................
7. Setting the functions (Main menu) COMMENT Function Selecting the comment Selecting the comment on printing from 4 types. OFF ........ Comment is not printed. COM ....... Printing the made comment C-T .......... Printing the made comment and the time and date when the image is stored in memory. The day and time is overlaid on comment. In this case, all the made comment may not be printed.) ADJ ......... Printing the setting value in the “1.COLOR ADJ” menu. DATA .......
7. Setting the functions (Main menu) 5 COMMENT Function Making a comment Making a comment on print Refer to pages 53-58 for details.
7. Setting the functions (Main menu) CONVERT Function This function is to output the selected input signal in the “INPUT SEL” function on “2. SIGNAL SET” menu to the VIDEO/RGB/S-VIDEO output terminal ON .......... Output the selected input signal to the VIDEO/RGB/S-VIDEO output terminal OFF ........ Output the signal from the input terminal to the same names as the input terminal .
7. Setting the functions (Making a comment) TOP/BOTTOM/LEFT/RIGHT Function Setting the print area By adjusting print area, the image size to be printed can be limited. Printing area adjustment can be operated with the setting menu on the screen. TOP ............. Top adjustment (setting area -16 to +134 ) BOTTOM ...... Bottom adjustment (setting area -134 to +16) LEFT ............ Left adjustment (setting area -34 to +270) RIGHT .........
7. Setting the functions (Making a comment) 1 Remote control function on the comment display MENU ........ Menu button Selecting 4 blocks on the comment menu A) B) Comment display block Character block C) D) Editing mode selecting mode CHANGE : OK/CANCEL , When pressing “MENU” button, the blocks will be switched in order of A → B → C → D → A... , Shift button , , ..... Use these buttons by the following operation a) Comment display block ..............
7. Setting the functions (Making a comment) 1 Editing command , Selecting each command in editing mode by pressing RIGHT or LEFT shift button. The letter inputting command CAPS (Capital Letters ) ........... Capital letters / small letters , When the SET button is pressed after selecting capital or small letter by pressing , button, the character block is switched in order of capital letters → small letters → capital letters....
7. Setting the functions (Making a comment) 1 Inputting the letter Selecting comment block MENU 1 Press the MENU button to select comment display block. , The selected block is displayed in green. SHIFT 2 Press the shift button , , , to select the inputting letter position. , Selected letter position is turned on or off in red. SHIFT Selecting characters block MENU 3 Press the MENU button to select the character block. , Selected block is displayed in green.
7. Setting the functions (Making a comment) 1 Inserting a space / deleting a character / Clearing the whole comment Insert a space, delete a character or clear the whole comment by the following procedure. (e.g.) In case of deleting “E”. MENU 1 Press the MENU button to select comment display block. , The selected block is displayed in green. SHIFT 2 Press the shift button , , , to select the deleting position. SHIFT MENU 3 Press the MENU button to select editor command block.
7. Setting the functions (Making a comment) 1 Close the comment menu MENU 1 Press the button to select “CHANGE : OK/CANCEL” . , “CHANGE” is displayed in blue. SHIFT 2 Press the shift button to select “OK” . , In case of changing a comment , select the “CANCEL” . SET 3 Press the SET button. , “MAIN MENU” display is shown. SET 4 Press the SET button. , “SAVE PRG 1/2/3” is selected. Note: Only one comment can be set among program 1,2 and 3. SET 5 Press the SET button.
7. Setting the functions (Memory SW menu) SETTING FUNCTIONS 2 MEMORY SW MENU When pressing the POWER button while pressing the MEMORY button on the front panel with the POWER turned off the MEMORY SW MENU is displayed. (e.g.) Monitor display: MEMORY SW MENU → KEY SET → KEY LOCK 1 Item and setting are as shown below . 1.TIME ADJ ........................ Date / Present time 2. KEY SET ....................... Invalid the buttons' function, Memory button function 3. SIGNAL ADJ ..................
7. Setting the functions (Memory SW menu) 1 TIME ADJ Setting the day and present time TIME ADJ ( Time Adjust ) Function Setting the day and present time. Refer to pages 11-13 for setting. 2 KEY SET Setting the buttons' function KEY LOCK Function The function on the remote control buttons and all of the buttons of the unit except POWER button are not available. ON .......... The function on the remote control buttons except MEMORY, PRINT, MONITOR, MEMORY PAGE are not available. OFF ........
7. Setting the functions (Memory SW menu) CLEAR KEY ( Memory and Clear ) Function Setting the CLEAR button function on the remote control. ONE ........ Pressing the CLEAR button on the remote control, the memorized image being selected is cleared. ALL ......... Pressing the CLEAR button on the remote control, all of the stored memorized images are cleared. 3 SIGNAL ADJ IN Signal setting display SYNC Function Selecting the level of input sync.signal. 0.3 V ............ Composite Sync. of 0.
7. Setting the functions (Memory SW menu) H -START (H - Position ) Function Adjust the H-position timing for the special signal . NML (Normal) .......... Inputting PAL signal FRONT .................... Inputting the special signal When the image is imbalanced and cannot be corrected by H-POSI on basic printing, set to “FRONT”. When setting to “FRONT”, the printing image may distorted in the special playback of VCR because “AFC” (“MAIN MENU” → “2. SIGNAL SET” ) is invalid.
7. Setting the functions (Memory SW menu) MARGIN CUT Cut the print paper so that the upper margin is small. Function ON .......... Small margin OFF ........ Behind the margin Margin cut ON OFF This function is convenient when putting the print on prints on records or non-PVC sleeves for print orchiving. This feature also saves paper. V POSITION Function Adjusting the vertical position of printing image.
7. Setting the functions (Memory SW menu) 5 SYSTEM System setting 2 PRG ALL INIT ( Program All Initial ) All settings of 3 memory programs to store each function is initialized. ON .......... Each setting function is initialized OFF ........ Not initialized This function is available when selecting “OK” in the “CHANGE : OK/ CANCEL/INIT” of “MEMORY SW MENU” and pressing the SET button.
8. Printing procedures (Special prints) The following printing is available. 1 MULTI prints 1 SAME or DIFF ................................................................. Pages 68 - 71 2,2s,4, or 16 images can be printed on a sheet. 1 2/2s-image 1 4-image 1 16-image S-size paper L-size paper S-size paper L-size paper S-size paper L-size paper 2 PHOTO prints 1 Photo prints can be made on two types of the sheet in the market and a card size sheet (suited size to stick on a business card.
8. Printing Procedures (Special prints) 1 Memory pages 1 The image size to be memorized is 1216 by 1200 dots. The following functions are available on this unit. The following is an example of S size paper. 1 2-image prints (MULTI prints) , In FRAME mode, 2 images can be memorized on one page. example : VIDEO FRAME [ A B ] (Display on the monitor) B A the image A and image B for 1 page (Only in the case of 2-images) , In FIELD mode, 4 images can be memorized on 2 pages.
8. Printing Procedures (Special prints) 1 16-image prints (MULTI prints) , In FRAME mode, 16 images can be memorized on 1 page. example : VIDEO FRAME (Display on the monitor) 16 images on 1 page 1 Image size and the number of memory pages Number of memory pages No.
8. Printing Procedures (Special prints) 1 MULTI PRINTS 1 2, 2s, 4 or 16 images can be printed on a sheet. , The following prints are available. Setting of the No. of images S size prints One image printing L size prints A A A A A A 2 A A 2s AA AA AA AA A A A A A A A A 4 16 A A A A A A A A A A A A A A A A A A A A A A A A example : “W” is selected on “SIZE” in 6.SYSTEM. “OFF” is selected on “SEPARATE” in 3.ADDITIONAL. “A” shows the direction of images.
8. Printing Procedures (Special prints) 3 Press the DOWN or UP button to select “MULTI : OFF/ON”. Then, press the RIGHT button to select “ON”. , “MODE : SAME/DIFF/PHOTO” is displayed on the menu screen. , “IMAGES : 2 / 2s/ 4/ 16” is displayed on the lower line. 4 Press the DOWN button to select “MODE : SAME/DIFF/PHOTO”. Then, press the RIGHT button to select “SAME” or “DIFF”. , When “SAME” is selected, a multi-image (2, 2s, 4 or 16 images) of the same image can be printed.
8. Printing Procedures (Special prints) 1 Storing images in memory 1 Press the DISPLAY button to display the set conditions. 2 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. 3 Press the MONITOR button and select the source image (“LIVE” is displayed on the monitor.) to display the image to be stored in memory. 4 Press the MEMORY button to store the image to be printed.
8. Printing Procedures (Special prints) When “MODE” is set to “SAME”, or “MODE” is set to “DIFF” and “IMAGES” to 2(or 2s) , When “MODE” is set to “SAME”, or “MODE : DIFF” and “IMAGES” is set to 2(or 2s), only one image is displayed on the monitor screen. 1 Press the DISPLAY button to display the set conditions. 2 Press the MONITOR button. Select source image (“LIVE” is displayed on the monitor.) to display the image to be stored in memory.
8. Printing Procedures (Special prints) 2 PHOTO PRINTS 1 PHOTO print is a function to print the images on the photo size (3x4cm, 5x5cm) and card size (2x1.5cm ). , CARD size print is suited to stick on a business card. , The following prints are available. Memorized image on the monitor Separate ON L size prints Separate OFF A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A AA AA A A A A A A A A AA AA AA AA A A MEMORY AA AA AA AA PRG.
8. Printing Procedures (Special prints) 1 Selecting the size 1 Press the DOWN button to select “IMAGES : CARD / 3*4 /5*5” menu. 2 Press the RIGHT button to select “CARD” , “3*4” or “5*5”. 1 Displaying the image from input signal (source image) SET 1 Press the SET button. , “CHANGE : OK/CANCEL” is selected. , When changing the PHOTO print setting, select “CANCEL”. SET 2 Press the SET button. , The MAIN MENU is displayed. SET 3 Press the SET button. , “SAVE PRG 1/2/3” is selected.
8. Printing Procedures (Special prints) 1 Printing the images 1 Press the MONITOR button to display the memorized image. (“MEMORY” is displayed on the monitor.) , A white frame is indicated on the displayed image. , The image within the white frame is photo-printed. PRG. 1 Q'ty 1 The white frame moves with the SHIFT buttons. A VIDEO FRAME [ A B ] example : When “3x4” or “CARD” is selected. MEMORY 2 Press the MEMORY PAGE button to select the memory page to print.
8. Printing Procedures (Special prints) 1 OPERATION 1 Setting the multi-print and photo-print menus Setting multi-print and photo-print functions 1 Press the MENU button. Then, press the UP or DOWN shift button to select “3. ADDITIONAL PUSH [ 2 Press the RIGHT shift button to select “3. ADDITIONAL”. 3 Press the DOWN shift button to select “MULTI : OFF/ON”. Then press the RIGHT ]”. shift button to select “ON” . , “MODE : SAME/DIFF/PHOTO” is displayed on the menu screen.
8. Printing Procedures (Special prints) SET B Press the SET button. , The source image (image from the input signal) is displayed. 1 Storing images in memory / Printing the images 1 Store the images to be printed in memory. , Refer to 1 MULTI PRINT or 2 PHOTO PRINT for storing images in memory. 2 Press the PRINT button. , The set SEPARATE images are printed. Note : , The distance between images in multi-print is different between on the monitor and the printed image.
8. Printing Procedures (Special prints) 1 Setting 1-image/multi-image memory 1 When memorizing 1 image in STROBE mode This setting is used to memorize 1 image in memory page [A B] (FRAME) or [A B C D] (FIELD). 1 Set the mode to 1-image. Select “OFF” in “MULTI : OFF” in “3. ADDITIONAL”. 2 Set the page increment function to ON. Set the “PAGE INC” to ON in “6. SYSTEM”. (The initial setting is “ON”.) , In FRAME mode, the image is memorized in the stored in memory page in order of page [A] → page [B]→ page [A].
8. Printing Procedures (Special prints) 1 Displaying the source image (image from the input signal) SET 1 Press the SET button. , “CHANGE : OK/CANCEL” is selected. , When changing the setting, select “CANCEL”. SET 2 Press the SET button. , The MAIN MENU is displayed. SET 3 Press the SET button. , “SAVE PRG 1/2/3” is selected. , This menu is used to store the setting in any one of 3 programs (1, 2 or 3). 4 Press the RIGHT or LEFT button to select the program number 1, 2 or 3 to store the setting.
8. Printing Procedures (Special prints) 1 Interrupting strobe memory , When any buttons on the remote control except MEMORY button is pressed, the strobe memory is interrupted. 1 Pressing the PRINT button To print the images stored in the strobe memory, follow the following procedures after interrupting the strobe memorization. 1 Display the desired image on the monitor. 2 Press the PRINT button. , The image stored in memory is printed.
8. Printing Procedures (Special prints) 3 Set the “PAGE INC” to “ON”. Set the “PAGE INC : ON/OFF” to “ON” in “6. SYSTEM” from the MAIN MENU. 4 Set the “MEM&PRINT” to “ON”. Set the “MEM&PRINT : OFF/ON” to “ON” in “2. KEY SETTING” from the MEMORY SW MENU. Displaying the source image (image from the input signal) SET 1 Press the SET button. , “CHANGE : OK/CANCEL” is selected. , When changing the setting, select “CANCEL” SET 2 Press the SET button. , The MAIN MENU is displayed.
8. Printing Procedures (Special prints) External REMOTE 2 terminal on the rear panel The images can be stored in memory and printed by sending the remote signal through the external remote terminal on the rear panel. , Make out the necessary circuit to use this function by referring to the following. Pin No. 1 External remote terminal Signal allocation Connector MINI DIN8PIN Pin No.
8. Printing Procedures (Special prints) 1 Circuit inside the VCP } VCP User side DC5V DTC124EK 10KΩ 100 Ω 22KΩ To VCP 2 MEMORY 22KΩ DC5V 2.2KΩ DTC124EK 100 Ω 22KΩ From VCP 4 BUSY 22KΩ DC5V DTC124EK 10KΩ 22KΩ To VCP 100 Ω 5 PRINT 22KΩ To VCP 1K 6 REMOTE Pin No. 6 REMOTE terminal By sending the following remote control codes from Pin No. 6, the same functions as the wired remote control (accessory) can be controlled.
8. Printing Procedures (Special prints) TIMING CHART Input signal level : TTL Input timing : 1 word 38.4 ms 1.6 ms Input timing : Code : “0” 0.4 ms 3.2 ms Input timing : Code : “1” 0.4 ms Example: print code = 13=010011 1 1 0 0 1 0 External REMOTE 1 terminal on the rear panel • The pin number on the positive pin is shown below. 3 2 1 132 1 External remote terminal Signal allocation Connector REMOTE 1 Pin No.
9. Troubleshooting 1 Error messages and countermeasures 1 If for some reason printing is not possible or error occurs during printing, the error message will be displayed on the monitor screen or LCD. In this case, follow the procedure described below. Error messages DOOR OPEN PAPER EMPTY Causes Countermeasures The printing unit is not inserted correctly. Insert the printing unit until it is locked in the unit. Paper is not set. Set the print paper correctly. Paper is not set correctly.
9. Troubleshooting Other messages MECHA INITIALIZE REQUEST Indicated when the power is turned on after turning off during printing. Press the MEMORY button for more than one second while pressing the MONITOR button. *Note : 3 MECHA INITIALIZE Indicated during initializing. PRINT STOP In the case of pressing the STOP button on the remote control during printing, this unit is initialized. This message is indicated during initializing. *Note : 3 This is an operation for initialization.
9. Troubleshooting 1 Before calling for service Symptom 1 No power Check and Remedy Is the power cord plug disconnected from the outlet? → Connect the power cord plug to the outlet firmly. After turning the power off, wait for approx. 2 minutes. Then turn the power ON. 1 No image appears on the monitor Are the sync.polarity of the monitor (SYNC : NEGA POSI), the output level of the sync.signal (OUTPUT SYNC RGB) and the RGB output sync. signal (RGB OUT) set correctly? → Check the current setting.
9. Troubleshooting Symptom 1 The stored image in the memory cannot be enlarged to fill the maximum print area. Check and Remedy Is the SMALL size ink-sheet installed when selecting “S” in “MODE : S/L”? Or is the LARGE size ink-sheet installed when selecting “L” in “MODE : S/L”? → Check the current setting. Refer to pages 31 - 32. Is the paper size set to “N” in the size setting in SYSTEM menu? → Set the size to “M” or “W”. Refer to page 51.
10. Options The following types of ink sheets and print papers are sold separately. Ink sheet Product name PK700S PK700L Ink sheet size S size L size No. of prints 200 130 Usage For 3 color use For 3 color use Print paper Product name CK700 K65H K65HM No. of prints Print size For S and L size S size : Approx. 200 L size : Approx. 130 For S and L size S size : Approx. 200 L size : Approx. 125 For S and L size S size : Approx. 200 L size : Approx.
11. Specifications Class Colour Video Copy Processor Model CP700E Printing method Sublimation Dye Thermal 3 colour faces progressive printing ( yellow, magenta and cyan) Print quality Dot resolution max.1216 x 600 pixels Number of grades Printing time 256 for each color Approx.38 sec./ sheet (L size high speed mode) Approx.51 sec./ sheet (L size standard speed mode) Approx.22 sec./ sheet (S size high speed mode) Approx.29 sec.
Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (1) 707 276100 FAX (1) 707 278755 German Branch Gothaer Strasse 8, Postfach 1548, 40880 Ratingen 1, Germany Phone (2102) 4860 FAX (2102) 486-732 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.