ID PHOTO SYSTEM DIS710E OPERATION MANUAL MONITOR ALARM SHEET PAPER MEMORY PRINT S-VIDEO POWER OPEN REMOTE
CONTENTS Page 1 SAFETY PRECAUTIONS ......................................................................................... 3 - 5 2 UNPACKING ................................................................................................................... 6 3 PRINTER SETUP ..................................................................................................... 7 - 9 4 CONNECTION .......................................................................................................
1. SAFETY PRECAUTIONS In the interest of safety, please observe the following precautions: POWER REQUIREMENT This system is designed for operation on 220V-240V, 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency. WARNNG: THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE. PROTECTIVE MEASURES IF ABNORMAL OPERATIONS OCCUR, .....
BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury. Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the cables provided INSTALLATION LOCATIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on the top, sides and bottom of this unit.
CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices. CONNECTING DEVICES Read thoroughly "Operating Precautions" of the instruction booklets for the devices connected with the Colour Video Copy Processor. The power cord must be disconnected after printing is over.
2. UNPACKING Take the unit out of the box by the following procedures. Make sure to check the contents. 2 PRINTER 1 2 3 4 Open the top of the box. Remove the accessory box. Remove the cushion above the unit. Take the unit out of the box carefully. Make sure to keep the unit horizontal. Then, unwrap the packing. • Accessory box Remote control Power cord Operation manual Sheet “Installing print paper and ink Ink cassette sheet” 2 CAMERA, ETC. 1 2 3 4 6 System cable Open the top of the box.
3. PRINTER SETUP Before printing a photo, install a print paper and ink cassette. REMOVING SCREW AND CUSHION See CP710E operation manual for details. 2 REMOVING SCREW 1 Remove the screw at the bottom of printing unit with a screwdriver or coin. Transport screw 2 Set the removed screw to the hole on the rear panel to keep. If you attach the connection box, refer to page 11. Stored position 1 2 REMOTE S-VIDEO VIDEO AC LINE 2 REMOVING PROTECTIVE CUSHION 1 Press the OPEN button on the front panel.
2 Insert the print paper in the position as shown right. Place the gear to the right side. Set the paper roll first on the right side paper holder. Then, set the paper roll on the left side paper holder. Right side Holder Print paper Install Left side Holder 3 Insert the print paper between roller 1 and 2. 4 Insert the edge of the print paper to roller 3. Print paper Be sure to insert the paper straight.
INSTALLING THE INK SHEET White roller Install the ink cassette with the ink sheet rolls before inserting the ink cassette into the printer. E 1 Put the coloured roller of the ink sheet to the ink cassette. A B B C A 2 Put the thin stick of white roller to the ink cassette. C 3 Put the thick stick of white roller to the ink cassette. DE Coloured roller E D D On the position, turn the roller and set the notch of the roller side to the hole of the cassette.
4. CONNECTION CABLE CONNECTION Connect the components as follows.(example) Make sure to turn off each device when connecting. If you wish to fix the connection box to the printer, set them first before connecting with cables.
SET UP CONNECTION BOX There are two ways to set connection box. FIXING TO THE PRINTER 1 1 Loosen three screws on the back of the printer. 2 REMOTE S-VIDEO VIDEO AC LINE 2 Catch the hooks of the connection box on each screws on the printer. Printer Connection box Hook 3 Fix the three screws and the transport screw. Screw 1 2 REMOTE S-VIDEO VIDEO AC LINE PUTTING ON THE PRINTER Remove 1 Remove the hook. Take the hook out of the connection box by removing the screw.
5. TAKING THE FIRST PICTURE You can take a picture twice, and choose the better one. 1 Turn on the power of this system. Make sure to turn on the power of the connection box first. Then, turn on the power of the camera and the printer. MONITOR ALARM SHEET PAPER MEMORY PRINT S-VIDEO POWER OPEN REMOTE 2 Attach a guide sheet with a circle on the LCD. Guide sheet A : for use in France, Germany, Italy, Spain, U.K.
8 Press MEM button to transfer the image to the printer. The image is memorized in the printer. 9 Press SHOT button to display the source image. A Press SHOT button again. The second image is memorized in the camera. 2nd image B Select the image to be printed. Press C/P button to switch between the two images. “C”(image in the camera) or “P”(image in the printer) is shown on the LCD. C/P C Print the image.
6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY To adjust the image source first is the key to get maximum picture quality. 2 CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are sure that the camera is providing the best picture quality and colour balance, adjust the printer setting. Make sure to adjust the camera setting in the same condition which you actually take a picture. For Iris setting, see the table shown right.
7 Press SHOT button to take a picture. Check the brightness of image. If the brightness is not improved, repeat the steps get the best setting. 2 to 6 to 2 ADJUSTING THE COLOUR OF IMAGE (WHITE BALANCE) Default setting is flash light W.B. If you are not satisfied with this setting, please proceed as follows. 1 Place a piece of white paper in front of the camera and display it to cover the LCD. Place white paper at the actual position where the subject would normally sit.
6 Press ZOOM button to finish the white balance setting menu. 2 FINE-ADJUSTING OF COLOUR When more colour adjustment is necessary after adjusting white balance, use a remote control of the printer. 1 Connect the remote control to the printer or the camera. MONITOR ALARM SHEET PAPER MEMORY PRINT S-VIDEO or POWER OPEN REMOTE If the printer is not turned on, turn on the power. DISPLAY COLOR ADJUST PROG. DISPLAY FIELD /FRAME COLOR ADJUST PROG.
7. FEATURES AND FUNCTIONS CAMERA (FRONT) 8 9 3 21 54 6 7 SHOT B/W MEM IRIS WB MENU PRINT ZOOM C/P 1/2/3 23 4 6 75 SET DOWN 1 LCD UP 8 Displays a source image, image memorized in a camera, and program number. 2 POWER INDICATOR 3 SHOT BUTTON 2 3 4 5 6 7 8 9 Press to turn on power. Press again to turn off power. This button is only for the camera. Make sure to turn on the connection box at this time.
8 UP BUTTON, SET BUTTON, DOWN BUTTON On ZOOM mode: Use to adjust zoom. Press UP to zoom up (TELE) and DOWN to zoom back (WIDE). On IRIS mode: Use to switch iris between auto and manual. Use also to set value at manual adjustment. On WB/PR mode: Use to switch white balance between auto and manual. On MENU mode: Use to select and set items on the menu screen. 9 ZOOM BUTTON Press to zoom or switch focus between auto and manual. A MENU BUTTON Press to display menu.
8. ADVANCED SETTING CHANGING SETTINGS You can print 1, 2, 4, 6 and 16-image on a sheet. To make 1 and 16-image print, change the setting as follows. 2 PRINTING 16- OR ONE-IMAGE ON A SHEET Use the remote control of the printer to print 16-image on a sheet. 1 Select the PRG. No. to be changed with the switch on the camera. MONITOR ALARM 2 Connect the remote control to the printer or the camera. SHEET PAPER MEMORY PRINT S-VIDEO or POWER OPEN REMOTE DISPLAY DISPLAY COLOR ADJUST PROG.
"L" is indicated on red. U 2 CHANGING ZOOMING SPEED LENS SET button. ZOOM FOCUS RETURN 3 Press UP or DOWN button to select ZOOM, then press LENS BRIGHT STROBE ------DETAIL COLOR SUB-MENU PRESET-WRITE END SET button. MENU 1 Press MENU button on the camera. 2 Press UP or DOWN button to select LENS, then press 4 Press UP or DOWN button to select SPEED, then press 2 SELECTING AUTO/MANUAL FOCUS 1 Press MENU button on the camera. 2 Press UP or DOWN button to select LENS, then press SET button.
THE BEST CONDITION FOR THIS SYSTEM 2m MONITOR ALARM SHEET PAPER MEMORY PRINT S-VIDEO POWER OPEN REMOTE 0.3m 0.3m 1.5m to 2m 2 EFFECT OF BACK FLASH • The back flash reduces the shadow behind the subject.
9. TROUBLESHOOTING BEFORE CALLING FOR SERVICE Use the following troubleshooting chart to resolve any apparent defect in operation. If you are unable to resolve the problem, unplug the power cord and contact your dealer. Causes Countermeasures No power • Is the power cord plug disconnected from the outlet? Connect the power cord plug to the outlet firmly. • Are the camera, printer and connection box turned on? Confirm that they are turned on.
10. SPECIFICATIONS Printer Camera Printing method Sublimation Dye thermal Image pickup device 1/4" CCD (total 470,000 pixels) No. of effective pixels 752H x 582V (440,000 pixels) Signal system PAL colour system Scanning system 625 lines; 2:1 interlace Scanning frequency 15.625 kHz (H), 50 Hz (V) Sync.
Name of Importers Mitsubishi Electric Europe B.V. Benelux Branch Nijverheidsweg 23 A, 3641 RP. Postbus 222, 3640 AE Mijdrecht Phone 02972-82461 FAX 02972-83936 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.