- Mitsubishi Digital Electronics DVR User Manual

58
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
♦ CALL OUT SETTINGS
The CALL OUT settings are used with the rear CALL OUT
terminals outputting a signal to notify of a specified condition.
CALL OUT SETTINGS use photo-coupler output to
decrease the amount of malfunctions due to writing .
See page 19 “CALL OUT Output terminal” for apt con-
nection procedures.
• HDD MAIN REMAIN/HDD SUB REMAIN/
ARCHIVE REMAIN
When the remaining memory in the HDD or ARCHIVE
device reaches the set value, the unit outputs a signal
from the CALL OUT terminal, and the “REC/REM” or
“ARCHIVE/REM” warning displayed on the screen.
<CALL OUT SETTINGS>
>> HDD MAIN REMAIN OFF
HDD MAIN FULL OFF
HDD SUB REMAIN OFF
HDD SUB FULL OFF
ARCHIVE REMAIN OFF
ARCHIVE FULL OFF
“HDD SUB REMAIN” appears when “PARTITION”
is selected on “HDD SETTING” of the <INITIALIZA-
TION> screen.
“ARCHIVE REMAIN” appears when “ARCHIVE•
COPY” is selected on “ID4•ID5” of the <INITIALIZA-
TION> screen.
Setting ( default : “OFF” )
“2%”, “4%”, “6%”, “8%”, “10%”, “15%”, “20%”, “30%”,
“40%”, “50%”, “OFF”
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } <REAR TERMINAL SETTINGS> }
Select “HDD MAIN REMAIN”, “HDD SUB REMAIN” or
“ARCHIVE REMAIN” in the <CALL OUT SETTINGS> screen.
Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button to exit.
By pressing the WARNING RESET button, the HDD
capacity and archive capacity warning from the CALL
OUT terminal can be cancelled.
INFORMATION
For the relationship of the warning display and CALL
OUT signal output, see pages 96, 97. Although the
warning will be displayed regardless if the output item
for the CALL OUT signal is set to “Fixed”, the condition
to output CALL OUT signals can be added when the
output is set to “Selectable”. For example, the buzzer
can be set to sound when reaching a value set in “HDD
MAIN REMAIN”, “HDD SUB REMAIN” or “ARCHIVE
REMAIN” of the <CALL OUT SETTINGS> screen if
“BUZZER” in the <REAR TERMINAL SETTINGS>
screen is set to “WARNING”.
• HDD MAIN FULL/HDD SUB FULL/ARCHIVE FULL
When the HDD is full, the CALL OUT terminal outputs a
CALL OUT signal.
<CALL OUT SETTINGS>
HDD MAIN REMAIN OFF
>> HDD MAIN FULL OFF
HDD SUB REMAIN OFF
HDD SUB FULL OFF
ARCHIVE REMAIN OFF
ARCHIVE FULL OFF
“HDD SUB FULL” appears when the HDD SET-
TING is selected on “PARTITION” of the <INITIALIZA-
TION> screen.
“ARCHIVE FULL” appears when the ID4•ID5 is
selected on “ARCHIVE•COPY” of the <INITIALIZA-
TION> screen.
Setting ( default : “OFF” )
“ON” : Signal is outputted when the recording capacity
becomes full.
“OFF” : No signal is outputted when the recording ca-
pacity becomes full.
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } <REAR TERMINAL SETTINGS> }
Select “HDD MAIN FULL” , “HDD SUB FULL” or “ARCHIVE
FULL” in the <CALL OUT SETTINGS> screen. Display the
desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
♦ EMERGENCY REC DURATION
The recording time for emergency recording can be set.
<REAR TERMINAL SETTINGS>
MODE OUT 1 OFF
MODE OUT 2 OFF
MODE OUT 3 OFF
MODE OUT 4 OFF
MODE OUT 5 OFF
KEY SOUND ON
BUZZER OFF
REMAIN HDD MAIN-10
%
CALL OUT SETTINGS
>> EMERGENCY REC DURATION 10M
For details concerning setting EMERGENCY RE-
CORDINGS,
see page 72.
Setting ( default : “10M” )
“1M”, “2M”, “5M”, “10M”, “20M”, “30M”, “60M”
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select “EMERGENCY REC
DURATION” in the <REAR TERMINAL SETTINGS> screen.
Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button to exit.
■ COMMUNICATION PORT SETTINGS
<INITIAL SET UP/INFORMATION>
HDD SETTINGS
AUDIO RECORDING OFF
REAR TERMINAL SETTINGS
>> COMMUNICATION PORT SETTINGS
CAMERA CONTROL
INFORMATION/SERVICE
PASSWORD
LANGUAGE SELECTION
<INITIAL SET UP/INFORMATION> (continued)