ENGLISH DLP™ PROJECTOR MODEL EX240U/EW270U User Manual EX240U/EW270U This User Manual is important to you. Please read it before using your projector.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste. If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration.
Contents Important safeguards ............................................................................................................................. 5 Projector exterior view .......................................................................................................................... 7 Controls and functions........................................................................................................................... 8 Positioning your projector ..............................
Please read all these instructions regarding your projector and retain them for future reference. Follow all warnings and instructions marked on the projector. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions The safety and operating instructions should be retained for future reference. 3. Warnings All warnings on the appliance and in the operating instructions should be adhered to. 4.
WARNING: Unplug immediately if there is something wrong with your projector. Do not look into the air outlet grilles when projector is operating. Heat, dust, etc. may blow out of them and hurt your eyes. Do not operate if smoke, strange noise or odor comes out of your projector. It may cause fire or electric shock. In this case, unplug immediately and contact your dealer. Do not block the air inlet and outlet grilles. Never remove the cabinet. Do not use flammable solvents (benzene, thinner, etc.
Projector exterior view 1 6 2 9 2. 3. 4. 5. 6. 7. 8. 9. External control panel (See "Projector" on page 8 for details.) Lamp cover Vent (heated air exhaust) Quick-release button Lens cover Focus ring and Zoom ring Front IR remote sensor Projection lens Vent (air intake) ENGLISH 1. Front/upper side Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns. 3 4 7 8 5 Rear/lower side 10 11 12 13 14 15 16 20 17 18 10.
Controls and functions Projector 1. 1 8 2 3 9 4 10 2. 12 6 7 3. POWER indicator light Lights up or flashes when the projector is under operation. See "Indicators" on page 53 for details. 4. SOURCE Displays the source selection bar. See "Switching input signal" on page 24 for details. 13 11 Zoom ring Adjusts the size of the image. See "Fine-tuning the image size and clarity" on page 25 for details. 11 5 Focus ring Adjusts the focus of the projected image.
6. 1 2 7 8 9 3 10 4 11 12 7. 8. 5 9. 10. POWER FREEZE Freezes the projected image. See "Freezing the image" on page 33 for details. 3. 11. Left Selects the desired menu items and makes adjustments. See "Using the menus" on page 22 for details. 12. 4. BLANK VOLUME keys (+, -) Adjusts the sound level. See "Adjusting the sound" on page 33 for details. / Down) AUTO Right/ / SOURCE Displays the source selection bar. See "Switching input signal" on page 24 for details.
Remote control effective range Infra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (~ 26 feet). Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam. Ap p rox.
Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the possible installation locations: 1. Front Table 3.
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. 4:3 is the native aspect ratio of EX240U. To be able to project a complete 16:9 (widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the projector's native aspect width. This will result in a proportionally smaller height equivalent to 75% of the projector's native aspect height.
1. 2. 3. 4. 5. Determine the aspect ratio of your screen, 16:9 or 4:3. If you have a 4:3 screen, refer to the table labeled "(Standard)". If you have a 16:9 screen, refer to the table labeled "(16:9)". Select your screen size. Refer to the table and find the closest match to your screen size in the left columns labeled "Screen". Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labeled "Distance from the screen: L".
Layout of the projector Image size varies depending on the distance between the screen and the projector. Front projection W B H A Hd A=B L L: Between the screen and the front edge of the projector H: Height of the projected image (Standard) EX240U Diagonal Size inch cm Screen Width: W inch cm Height: H inch cm Distance from the screen: L Shortest (Wide) Longest (Tele) inch m inch m Hd inch cm 40 102 32 81 24 61 60 1.5 66 1.7 2 6 60 152 48 122 36 91 90 2.3 99 2.
Diagonal Size inch cm Screen Width: W inch cm Height: H inch cm Distance from the screen: L Shortest (Wide) Longest (Tele inch m inch m ENGLISH (16:9) EX240U Hd inch cm 40 102 35 89 20 50 66 1.7 73 1.9 6 15 60 152 52 133 29 75 99 2.5 109 2.8 9 22 30 80 203 70 177 39 100 132 3.4 146 3.7 12 100 254 87 221 49 125 166 4.2 182 4.6 15 37 150 381 131 332 74 187 248 6.3 273 6.9 22 56 200 508 174 443 98 249 331 8.4 364 9.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. • See the owner’s guide of each device for details about its connections. • Contact your dealer for details about its connections. • In the connections shown below, some cables may not be included with the projector. They are commercially available from electronics stores.
If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the MONITOR OUT signal output jack on the projector to an external monitor following the instructions below: To connect the projector to a monitor: 1. 2. Connect the projector to a computer as described in "Connecting a computer" on page 16. Connect the RGB cable from the monitor to the MONITOR OUT jack of the projector.
Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. To connect the projector to an HDMI device: 1. 2. Take an HDMI cable and connect one end to the HDMI output port of the video device. Connect the other end of the cable to the HDMI input port on the projector.
Audio cable (option) Component Video to RGB (D-Sub) adaptor cable (option) ENGLISH The final connection path should be like that shown in the following diagram: Speakers or Audio cable (option) AV device If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. 2. 3. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
Operation 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. • Ask your installation specialist to provide an Earth leakage breaker. When you do not use the projector, be sure to shut down the main power by the breaker. • Please use the original accessories (e.g.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Main menu Highlight Status Sub-menu Press MENU/ EXIT to go back to the previous page or to exit. Current input signal Below is an example about how to set the OSD language. 1. Press MENU/EXIT on the projector or remote control to turn the OSD menu on. 3. Press to highlight Language and press to select a preferred language. 2.
For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 22. You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password.
Password: __ __ __ __ __ __ Keep this number in a safe place. 5. 6. 7. Confirm the new password by re-entering the new password. You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started. To leave the OSD menu, press MENU/EXIT. Disabling the password function To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock menu after opening the OSD menu system. Select Off by pressing / .
Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine tune the horizontal angle.
Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image.
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): 1. 2. 3.
5. Full: Scales an image to full screen size (16:10). The image is projected to fit all over screen.
Optimizing the image ENGLISH Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select a operation mode that suits your need, you can follow one of the following steps. • • Press MODE/ENTER on the remote control or projector repeatedly until your desired mode is selected. Go to the PICTURE > Setting menu and press / to select a desired mode.
Fine-tuning the image quality in user modes According to the detected signal type, there are some user-definable functions available when User 1 or User 2 mode is selected. You can make adjustments to these functions based on your needs. Adjusting Brightness Highlight Brightness in the PICTURE menu and adjust the values by pressing control. / on the projector or remote The higher the value, the brighter the image. And lower the setting, darker the image.
In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room. Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.
Setting the presentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. 2. Press TIMER SET UP on the remote control or go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page. Press to highlight Timer period and decide the timer period by pressing / .
ENGLISH Hiding the image In order to draw the audience's full attention to the presenter, you can use BLANK on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden.
1. 2. Repeat steps 1-2 above. Press to highlight Volume and press / to select a desired sound level. Standby Audio Out Selecting On enables the function. The projector can output an Audio input signal when it is in standby mode and Audio input and Audio out jack is correctly connected to devices. When the projector enters standby mode, the audio will be interrupted briefly. This is not a product malfunction.
3D ENGLISH Watching 3D Content You can enjoy 3D Content with this projector. In order to watch 3D Content, you need to have the following items: 1. Field-sequential 3D video contents 2. DLP Link active electronic shutter glasses (Field-sequential: The system which displays alternately the image for the left eye and the right eye.
• 3D image may not appear on the screen depending on the PC performance such as graphics board, memory, or CPU. • The signals in the below table can be displayed with viewing 3D Contents on the projector. If a different signal is fed, the projector shows no 3D contents even with the 3D option set to On in the DISPLAY menu. Mode Resolution (H x V) Horizontal Frequency (Hz) Vertical Frequency (Hz) TV60, 480i (525i) - 15.73 59.94 VGA60 640 x 480 31.47 59.94 119.52 VGA120 640 x 480 61.
With a proper LAN cable connection and LAN Control settings, you can operate the projector from a computer using a web browser when the computer and the projector are connected to the same local area network. This projector supports Crestron® software. An example of connecting the projector to computer. External hub Computer LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) • When using an external hub or router, use a Category 5 straight cable.
Controlling the projector remotely through a web browser (e-Control™) Once you have the correct IP address for the projector and the projector is on or in standby state, you can use any computer that is on the same local area network to control the projector. When using this function, Adobe Flash Player has to be installed in your computer. Please download Adobe Flash Player from the website of Adobe Systems Incorporated. 1.
• After making the adjustments, press the Send button and the data will be saved in the projector. • Once the password is set, the Log Out button will display beside the Tools button. • Write down your selected password in advance or right after the password is entered so that it is available to you should you ever forget it. If you forget the password, you will not be able to log in. • The software is available in English language.
Glossary For more detail of the glossary below, refer to the technical book that is commercially available. Term Description DHCP Abbreviation for Dynamic Host Confi guration Protocol. This protocol automatically assigns IP Address to networked devices. IP Address Numerical address to identify networked computers. Subnet Mask A numeric value to defi ne the number of bits used for a network Default Gateway A server (or router) to communicate across networks (subnets) that are divided by Subnet Mask.
Menu operation ENGLISH Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu Options Wall Screen Off/Light Yellow/Pink/Light Green/Blue/ Blackboard Aspect Ratio Auto/Real/Full (EW270 only)/4:3/16:9 Keystone 1. DISPLAY Position Phase H. Size Magnify 3D On/Off 3D Sync 1/2 Setting Brightest/Presentation/Normal/Theater/ User 1/User 2 Brightness Contrast Color Tint 2.
Projector Position Front Table/Rear Table/Rear Ceiling/ Front Ceiling Auto Power Off Disable/5 min/10 min/15 min/20 min/25 min/30 min 4. SYSTEM SETUP: Blank Timer Basic Panel Key Lock Disable/5 min/10 min/15 min/20 min/25 min/30 min On/Off Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr Timer Controller Splash Screen Black/Blue/MITSUBISHI Quick Cooling On/Off Mute Audio Settings Volume Standby Audio Out Standby Monitor Out Menu Settings Lamp Settings 5.
ENGLISH Description of each menu FUNCTION DESCRIPTION Wall Screen Corrects the projected picture’s color when the projection surface is not white. See "Using Wall Screen" on page 31 for details. There are four options to set the image's aspect ratio depending on your input signal source. See "Selecting the aspect ratio" on page 27 for details. Corrects any keystoning of the image. See "Correcting keystone" on page 26 for details. Displays the position adjustment page.
FUNCTION Setting Brightness Contrast 2. PICTURE menu 3. SOURCE menu EN-44 Color Tint DESCRIPTION Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting a picture mode" on page 29 for details. Adjusts the brightness of the image. See "Adjusting Brightness" on page 30 for details. Adjusts the degree of difference between dark and light in the image. See "Adjusting Contrast" on page 30 for details.
4. SYSTEM SETUP: Basic menu DESCRIPTION Presentation Timer Language Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 32 for details. Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 22 for details. Projector Position See "Choosing a location" on page 11 for details. Auto Power Off Blank Timer Panel Key Lock Timer Controller Splash Screen Quick Cooling Audio Settings 5.
FUNCTION DESCRIPTION Change password Security Settings You will be asked to enter the current password before changing to a new one. Power on lock See "Utilizing the password function" on page 23 for details. Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions. 5.
Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Low mode) + 4/3 (hours used in Standard mode) See "Setting Lamp mode as Low" below for more information on Low mode. The lamp hour in Low mode is calculated as 3/4 of that in Standard mode.
When the lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
Replacing the lamp Spare lamp for EX240U/EW270U: VLT-EX240LP • Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.
• • EN-52 Do not reset if the lamp is not new or replaced as this could cause damage. This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For US only).
Indicators Power Status & Description Temp ENGLISH Light Lamp Power events Orange Off Off Stand-by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Red Orange Flashing Off Off Cooling down. Orange Flashing Off Red The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications ENGLISH Projector specifications All specifications are subject to change without notice. General Product name DLP™ Projector Model name EX240U EW270U Resolution 1024 x 768 XGA 1280 x 800 WXGA Display system 1-CHIP DMD Optical Lens F/Number F = 2.6 to 2.8, f = 21.1 to 23.0 mm Lamp 185 W lamp Electrical Power supply AC100–240V, 50/60 Hz (Automatic) Power consumption 3.
Dimensions 282 mm (W) x 94 mm (H) x 229 mm (D) (Not including protrusion) 233 282 229 94 110 50 68.3 Tolerance:±2mm Timing chart Supported timing for PC input Horizontal Frequency (kHz) Clock (MHz) 70.087 31.469 28.3221 59.940 31.469 25.175 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000 VGA_120 119.518 61.910 52.500 SVGA_60 60.317 37.879 40.000 SVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.
ENGLISH Supported timing for HDMI (HDCP) input Resolution Mode Vertical Frequency (Hz) Horizontal Frequency (kHz) Clock (MHz) 720 x 400 720x400_70 70.087 31.469 28.3221 VGA_60 59.940 31.469 25.175 VGA_72 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000 VGA_120 119.518 61.910 52.500 SVGA_60 60.317 37.879 40.000 SVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.250 SVGA_120 119.854 77.425 83.
Supported timing for Component-YPbPr input Signal Format Horizontal Frequency (kHz) Vertical Frequency (Hz) 480i(525i)@60Hz 15.73 59.94 480p(525p)@60Hz 31.47 59.94 576i(625i)@50Hz 15.63 50.00 576p(625p)@50Hz 31.25 50.00 720p(750p)@60Hz 45.00 60.00 720p(750p)@50Hz 37.50 50.00 1080i(1125i)@60Hz 33.75 60.00 1080i(1125i)@50Hz 28.13 50.00 1080P@60Hz 67.5 60.00 1080P@50Hz 56.26 50.00 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.
Mitsubishi Projector Warranty, Sales Support and Service Information North America MDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www.mitsubishi-presentations.com under Customer Care Sales & Inquiries Phone :Toll Free (888)307-0349 E-mail :ppdinfo@mdea.com Technical Inquiries Phone :Toll Free (888)307-0309 E-mail :TSUPPORT@mdea.com MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.
