- Mitsubishi Digital Electronics Switch User Manual

ManualsBrandsMitsubishi Electronics ManualsSwitchEXTRON 4XIXIXIXIXI

Extron • System 4

xixi

Switcher Series • User’s Manual • P/N 68-401-02 Rev. C

Configuration and Connections

Mitsubishi Installation

Page 1

SYSTEM 4

xixi

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: MITSUBISHI

Included Communications Adapter(s):

Quantity Part Number Description

1 26-473-01 ADP, UNV, “E”

1 26-475-01 ADP, UNV, “G”

1 26-458-01 ADP, UNV, “NEC-LCD MT”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: MITSUBISHI VS

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM

AS 1 2 3 4 CABLE ADAPTER

✔ VS off on off on 0 0 8 5 0 J15 26-473-01

LVP-X100 off on off on 0 0 6 F 0 J15 26-475-01

LVP-X200X300 off on off on 0 1 6 F 0 J15 26-475-01

LVP-X400 off on off on 0 2 6 F 0 J15 26-458-01

Page 1

Summary of content (7 pages)

PAGE 1
Configuration and Connections Mitsubishi Installation xi SYSTEM 4xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: MITSUBISHI Included Communications Adapter(s): Quantity 1 1 1 Part Number 26-473-01 26-475-01 26-458-01 Description ADP, UNV, “E” ADP, UNV, “G” ADP, UNV, “NEC-LCD MT” THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS ADAPTER(S) F
PAGE 2
Configuration and Connections Mitsubishi Installation xi to Mitsubishi LVP-X100 Connecting System 4xi If the System 4xi is already configured for a Mitsubishi LVP-X100 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Mitsubishi LVP-X100.
PAGE 3
Configuration and Connections Mitsubishi Installation 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. ______ Secure all of the connector screws. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output. Connect the 15-pin connector on the other end of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X100 connector panel.
PAGE 4
Configuration and Connections Mitsubishi Installation xi to Mitsubishi VS Projector Connecting System 4xi If the System 4xi is already configured for a Mitsubishi VS Projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Mitsubishi VS projector.
PAGE 5
Configuration and Connections Mitsubishi Installation 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (shown as CC 50') into the PJ Comm port on the System 4xi. The other end plugs into the other 9-pin male D connector on the Comm Adapter (mentioned in Step 5). ______ Secure all of the connector screws. 7.
PAGE 6
Configuration and Connections Mitsubishi Installation xi to Mitsubishi LVP-X200 Projector Connecting System 4xi If the System 4xi is already configured for a Mitsubishi LVP-X200 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1.
PAGE 7
Configuration and Connections Mitsubishi Installation 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (shown as CC 50') into the PJ Comm port on the System 4xi. ______ Secure the screws on all D connectors. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output. Connect the 15-pin connector on the other end of the RGBS/HV cable to the PC-1 Input connector on the Mitsubishi LVP-X200 connector panel.