User Guide

EN-23
Menu operation (continued)
2. INSTALLATION menu
• The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the
default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
• In AUDIO INPUT, HDMI audio is selected when the Input Source is HDMI input. The audio of AUDIO 1, AUDIO 2, AUDIO 3, and MIX cannot
be selected.
• To cancel the test pattern, press any button.
eFgnitteSnoitpo uneM ature description
WALL SCREEN
OFF/BEIGE / LIGHT
BLUE / LIGHT GREEN
/ PINK /BLACK
BOARD/WHITE BOARD
Selects a desired setting based on the color of the screen or wall
on which images are projected. When selecting a setting other
than BLACK BOARD/WHITE BOARD, you can fine-tune the color
tone to the desired level on the 1 to 5 scale. (See page 18.)
LAMP MODE
STANDARD
Select this setting when you want to view images in a well-lit
room.
LOW
Select this setting when you want to view images at a moderate
light intensity. The operating sound is consequently reduced, and
the lamp lifetime becomes longer.
• When this mode is switched, projected images may flicker.
• If this mode is frequently switched, the lamp may be deterio-
rated.
STANDBY MODE
STANDARD
LAN can be activated in STANDARD MODE. MONITOR OUT
cannot be activated.
LOW
Power consumption can be lowered when selecting LOW. How-
ever, LAN and MONITOR OUT cannot be activated.
AUDIO INPUT
AUTO
If AUTO is selected, selects AUDIO 1 when the input source is
COMPUTER 1, selects AUDIO 2 when the input source is COM-
PUTER 2, selects AUDIO 3 when the input source is VIDEO/S-
VIDEO, selects HDMI when the input source is HDMI.
AUDIO 1/AUDIO 2/AUDIO 3 Select the audio input.
MIX
Selects MIX signal of AUDIO 1 and AUDIO 2. You can change the
balance of AUDIO 1/AUDIO 2 using MIX .
AUTO POWER ON ON/OFF
When this mode is set to ON, the lamp is automatically lit when
the power cord is plugged in the wall outlet. Select ON when you
set the projector at the ceiling.
• When the lamp is off, the projector is in standby. Use the
remote control to turn on the lamp.
AUTO POWER OFF OFF/5-60 min
Selects a desired timer setting until the projector enters the
standby mode when there is no signal input from the source.
IMAGE CAPTURE SETUP Use to capture the screen for the splash screen. (See page 33.)
SPLASH SCREEN ON/OFF
Select ON to display the splash screen when the projector is pow-
ered on.
BACK COLOR BLUE/BLACK/IMAGE
Selects the background color that is displayed when there is no
signal input from the source.
AV MUTE MODE BLACK/IMAGE
Use to choose the background, either BLACK, or IMAGE,
which
will be displayed when the AV MUTE button is pressed. When
IMAGE is chosen, the splash screen will be displayed.
IMAGE REVERSE
OFF
Select this setting when you want to view images from the front
with the projector set on the floor.
MIRROR
Select this setting when you want to view images from behind the
screen with the projector set on the floor.
INVERT
Select this setting when you want to view images from behind the
screen with the projector set at the ceiling.
MIRROR INVERT
Select this setting when you want to view images from the front
with the projector set at the ceiling.
TEST PATTERN
CROSS HATCH
Select to show the test cross hatch pattern.
LAMP MODE
OFF
IMAGE
REVERSE
CROSS HATCH
WALL SCREEN
BEIGE
STANDBY MODE
STANDARD
STANDARD
AUDIO INPUT
AUTO
opt.
INSTALLATION
AUTO POWER
OFF
OFF
OFF
AUTO POWER
ON
IMAGE CAPTURE
ON
SPLASH
SCREEN
ON
BACK COLOR
BLUE
AV MUTE MODE
TEST PATTERN
BLACK
SETUP
WHITE
Select to show the maximum brightness image.
BLACK
Select to show the minimum brightness image.