LCD MONITOR MODEL MLM300 User Manual MLM400
Table of Contents Important Information .......................................................................................................................... 1 Safety Precautions, Maintenance, & Recommended Use ................................................................. 2 Contents .................................................................................................................................................... 3 Attaching LCD Options ..............................................
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Safety Precautions, Maintenance & Recommended Use Safety Precautions and Maintenance CAUTION FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MLM300 LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
Contents Your new MLM300 monitor box* should contain the following: • LCD monitor • Power Cord (3m) • Video Signal Cable – SC-B113 (4m) • User’s Manual • Wireless Remote Control and AA Batteries • Screw (M4 x 10) x 2 Ferrite Core x 2 • CD-ROM • Ferrite Core x 2 • Clamper x 2 Band • Band MLM400 Power Cord Video Signal Cable (D-SUB to D-SUB Cable) Clamper x 2 Screw (M4 x 10 ) x 2 LCD MONITOR MODEL MLM300 User Manual CD-ROM Wireless Remote Control and AA Batteries User’s Manual *Install an attache
Attaching LCD Options You can attach mounting accessories to the LCD monitor in one of the following two ways: Ventilation Requirements for enclosure mounting 1. In the upright position To allow heat to disperse, leave space between surrounding objects as shown in the diagram to the right. MLM300 MLM400 * 100 100 100 100 2.
Parts Name and Functions Control Panel MLM400 9 10 Button Location EXIT 8 1 POWER button ( 7 6 5 INPUT MUTE 3 2 4 ) 7 DOWN ( 1 ) button Switches the power on/off. See also page 17. NOTE: The Main Power Switch must be in the ON position for this Activates the on-scren menu when the on-screen menu is turned-off. Acts as button to move the highlighted area down to select the adjust- button to work. ment with on-screen menu. 2 MUTE button Switches the audio mute ON/OFF.
Parts Name and Functions –continued Terminal Panel L+ LRR+ RS232 9 8 5 VIDEO AUDIO VIDEO IN OUT IN 3 SPEAKER OUT 10 IN 2 RGB OUT OUT R G R/Cr/Pr G/Y B H V B/Cb/Pb H V L R S-VIDEO IN IN RGB 2 (D-SUB) RGB3 DVD/HD IN 7 6 4 RGB 1 (DVI-D) AUDIO 1 PC IN 3 2 1 1 AC IN connector 6 AUDIO IN 1,2,3 Connects with the supplied power cord. To input audio signal from external equipment such as a computer, VCR or DVD player.
Parts Name and Functions –continued Wireless Remote Control 5 4 7 VOLUME UP button 3 Increase the audio output level. 8 VOLUME DOWN button Decrease the audio output level. 9 PIP (Picture In Picture) button 1 ON/OFF button: Toggle switches between PIP-ON/ POP-ON/OFF. INPUT button: Select the ‘picture in picture’ input signal. CHANGE button: Replaces to the main picture and sub 2 picture.
Parts Name and Functions –continued Operating Range for the Remote Control Caution Point the top of the remote control toward the LCD monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor and at a hori- zontal and vertical angle of within 30° within a distance of about 3 m/10 ft.
Setup Procedure 1. Determine the installation location 6. Operate the attached external equipment CAUTION Display the signal on the external equipment you wish. Installing your LCD display must be done by a qualified technician. 7. Adjust the sound Contact your dealer for more information. Make adjustments when adjustment of the volume is required. 8. Adjust the screen (See pages 19-27) CAUTION MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE.
Connections Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment.
Connections –continued Connecting the LCD Monitor to a PC Connecting your computer to your LCD monitor will enable you to display your computer's screen image. Some video cards may not display an image correctly. • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the provided RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). • To connect the RGB 3 DVD/HD IN connector (BNC) on the LCD monitor, use a signal cable (mini D-sub 15 pin to BNC x 5).
Connections –continued Connecting to a Macintosh® Computer Connecting your Macintosh® computer to your LCD monitor will enable you to display your computer's screen image. Some video cards or drivers may not display images correctly. • • • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the provided RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). For older Macintosh® computers, use Macintosh cable adapter to connect to your Macintosh's video port.
Connections –continued Connecting to a Computer with a Digital Output Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. • The RGB 1 IN connector also accepts a DVI-D cable. • • • Input TMDS signals conforming to DVI standards. To maintain display quality, use a cable recommended by DVI standards. The AUDIO IN 1, 2 and 3 can be used for audio input. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button.
Connections –continued Connecting to a VCR or Laser Disc Player Connecting your VCR or laser disc player to your LCD monitor will enable you to display your VCR or laser disc player video. Refer to your VCR or laser disc player owner's manual for more information. To S-VIDEO OUT DIN 4 pin LCD monitor To VIDEO OUT To audio left ou tput To audio right ou tput DIN 4 pin VCR or Laser disc player RCA • • • Video signals can be connected to either the VIDEO IN [RCA or BNC] or the S-VIDEO IN connector.
Connections –continued Connecting to a DVD Player Connecting your DVD player to your LCD monitor will enable you to display your DVD video. Refer to your DVD player owner’s manual for more information. To connect the RGB 3 DVD/HD In connector (BNC) on the LCD monitor, use a separately available BNC connector cable. You will need a BNCto-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable (not provided).
Connections –continued Connecting to a Stereo Amplifier You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier owner's manual for more information. • • • • Turn on the LCD monitor and the amplifier only after all connections have been made. Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. Do not reverse the audio left and right jacks. The AUDIO IN 3 is used for audio input.
Basic Operation –Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on or red in off mode. The monitor can be powered on or off using the following three options: 1. Pressing the power button. MLM400 NOTE: Before operating the remote control, be sure to turn on the Main Power Switch on the LCD monitor. Power Button 2. Using the remote control MLM400 NOTE: Before operating the remote control, be sure to turn on the Main Power Switch on the LCD monitor. 3.
Basic Operation –continued Power Indicator On-screen Menu Information RGB1, 2, 3 Power Indicator Status Power ON RGB2 1024 x 768 ) 48kHz 60Hz AUDIO : 1 SCREEN SIZE : FULL Green Power OFF Red Power Standby Red and Green Video Input mode Input signal Information Audio input mode Picture Size mode DVD/HD When Using Power Management Function DVD/HD AUDIO : 3 SCREEN SIZE : WIDE The LCD monitor follows the VESA approved DPMS Power Management function.
On-Screen Menu Press UP or DOWN button to select sub-menu Controls Press SET –Computer Press UP or DOWN, and PLUS or MINUS button to select function, or control which you Press MENU or EXIT button to decide Remote Control SET Press UP or DOWN button to select SET SET SET Press INPUT button to decide Press UP or DOWN button to select Press INPUT button to decide Control Panel INPUT INPUT UP or DOWN button On-screen menu display INPUT button BRIGHTNESS BRIGHTNESS CONTRAST SHARPNESS BLACK
On-screen Menu BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET COLOR TEMPERATURE Controls COLOR TEMPERATURE L :SEL :SEL EXIT:PRE SET:NEXT MENU:END EXIT:PRE :SEL To adjust the color temperature of entire screen. Adjusting lower color temperature make the screen reddish and adjusting higher color temperature make the screen bluish. Selecting Picture Reset allows you to restore all PICTURE settings to the factory default position.
On-screen Menu Controls –Computer continued Main-Menu PICTURE SCREEN AUDIO PICTURE IN PICTURE CONFIGURATION 1 CONFIGURATION 2 AUDIO :SEL EXIT:PRE SET:NEXT MENU:END Sub-Menu TREBLE TREBLE BASS AUDIO RESET - BASS :SEL EXIT:PRE SET:NEXT MENU:END AUDIO RESET TREBLE BASS AUDIO RESET :SEL EXIT:PRE SET:NEXT MENU:END + :SEL :SEL EXIT:PRE SET:NEXT MENU:END TREBLE BASS AUDIO RESET To accentuate or control the high frequency sound.
On-screen AUTO BRIGHTNESS *:INPUT RGB2/3 only POWER SAVE Menu AUTO SETUP AUTO ADJUST AUTO BRIGHTNESS POWER SAVE LANGUAGE OSM TIME OFF TIMER SCREEN SAVER FACTORY PRESET Controls ON OFF :SEL LANGUAGE OSM TIME :SEL EXIT:PRE SET:NEXT MENU:END OFF TIMER AUTO SETUP AUTO ADJUST AUTO BRIGHTNESS POWER SAVE LANGUAGE OSM TIME OFF TIMER SCREEN SAVER FACTORY PRESET :SEL EXIT:PRE SET:NEXT MENU:END SCREEN SAVER AUTO SETUP AUTO ADJUST AUTO BRIGHTNESS POWER SAVE LANGUAGE OSM TIME OFF TIMER SCREEN SAVER FACTORY P
On-screen Menu Controls –DVD & HD Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION PICTURE :SEL EXIT:PRE SET:NEXT MENU:END Sub-Menu BRIGHTNESS BRIGHTNESS CONTRAST SHARPNESS COLOR BLACK LEVEL PICTURE RESET 50 - :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS COLOR BLACK LEVEL PICTURE RESET CONTRAST SHARPNESS COLOR BLACK LEVEL - Press + button to increase brightness. Press - button to decrease brightness.
On-screen Menu Controls –DVD & HD continued Main-Menu PICTURE IN PICTURE PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION :SEL EXIT:PRE SET:NEXT MENU:END Sub-Menu Selecting the size of picture inserted at the 'Picture-in Picture' (PIP) mode. 'Large', 'Middle', and 'Small' are available.
On-screen Menu Controls –AV Input Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION PICTURE :SEL EXIT:PRE SET:NEXT MENU:END Sub-Menu BRIGHTNESS BRIGHTNESS CONTRAST SHARPNESS TINT COLOR BLACK LEVEL NOISE REDUCTION PICTURE RESET 50 - + :SEL :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS TINT COLOR BLACK LEVEL NOISE REDUCTION PICTURE RESET CONTRAST SHARPNESS - :SEL BLACK LEVEL NOISE REDUCTION PICTURE RESET Adjusts the picture to have sharp or soft edges.
On-screen Menu TREBLE BASS AUDIO RESET BASS Controls - EXIT:PRE MENU:END NO YES :SEL EXIT:PRE SET:NEXT MENU:END :SEL EXIT:PRE Press + button to increase BASS sound. Press - button to decrease BASS sound. Selecting Audio Reset allows you to reset all AUDIO settings to the factory default position. AUDIO RESET AUDIO RESET continued + :SEL TREBLE BASS AUDIO RESET Input To accentuate or control the low frequency sound.
On-screen Menu LANGUAGE OSM TIME OFF TIMER SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET COLOR SYSTEM :SEL EXIT:PRE SET:NEXT MENU:END CONFIGURATION RESET LANGUAGE OSM TIME OFF TIMER SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END Controls AUTO NTSC PAL SECAM PAL60 4.43NTSC EXIT:PRE MENU:END CONFIGURATION RESET NO YES :SEL EXIT:PRE 27 Input continued Selecting the Color System depends on your input video format.
Using the LCD with a Personal Computer (PC) This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC MLM300 PC to RS-232C terminal RS-232C Cable Note: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details.
Using the LCD with a Personal Computer –continued 3) Control sequence (continued) *: The sending time of return command may delay depending on the condition (during changing of the input signal, etc.). [Example] Turn the power ON ( ' ' is for ASCII code) Sending commands Status code from LCD from the PC etc.
Features 30” diagonal screen size adds a new option to information display visual offerings. 1280 x 768 resolution allows for crisp text and precise images. No permanent phosphor image burn-in contributes to optimal screen performance and longer monitor life. Wide viewing angle DDC/CI capabilities allow control commands to be sent directly to the monitor through a standard PC or over an existing network by a system administrator.
Troubleshooting No picture • • • • • • The signal cable should be completely connected to the display card/computer. The display card should be completely seated in its slot. Front Power Switch and computer power switch should be in the ON position. Main Power Switch should be in the ON position (see Page 5 for location of this swtich). Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.
References Mitsubishi 30” LCD Monitor Customer Service & Support Customer Service and Technical Support: (888) 307-0309 (949) 859-4770 Fax: Parts and Accessories/Macintosh Cable Adapter: (888) 307-0309 Customer Service Policies & Processes: http://www.mitsubishi-presentations.com Online Technical Support Knowledge Base: http://www.mitsubishi-presentations.com Customer Service & Technical Support Email: tsupport@mdea.
Specifications Analog Input LCD Module Digital Input (29.5" / 75cm diagonal) Pixel Pitch 0.5025mm Resolution 1280 x 768 dots (WXGA) Color Over 16 million colors Brightness 450cd/m2 (Typ.) Viewing Angle Up 85 / Down 85 / Left 85 / Right 85 (typ) @ CR >10 External speaker output inpedance Rating 7W x 7W (8 Ohm) Frequency Horizontal 31.5kHz - 49.0kHz, 64.0kHz:SXGA, 75.0kHz:UXGA 31.5kHz - 48.4kHz (PC Input) Vertical 58.0 - 62.0 Hz 58.0 - 62.0 Hz Pixel Clock 25.0MHz - 162.0MHz 25.
Limited Warranty (Applicable only for Customers who bought and used their products within US Territories) 1. Subject to the terms and conditions in this limited warranty, MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
Mitsubishi MLM300 PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of Mitsubishi Digital Electronics America and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others.
