- Mitsubishi Digital Electronics User Manual Projection HDTV

12
Chapter . . .
AN T - A
A N T- B
LO O P
OUT
WS-48413, WS-55413, WS-65413
Back Panel
COMP O N ENT
480 i / 4 80 P/ 1080i
2
1
Y
P r
Pb
AUDI O -
RIGHT
L E F T /
(
M
O
N
O
)
AUDI O -
Y
G
Pb
B
P r
R
V
H
DTV(YPbPr/ GBRH V )
48 0 i / 48 0P /108 0 i
I N P U T
2
1
AU DI O -
R IGH T
AU DIO-
LE F T /
(MONO)
V I D EO
S-VIDEO
M
O
N
I
T
O
R
OUT
SERVICE WARNING
MONITORLINK
TM
/DVI
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
CAUTION: TO MEASURE SECOND ANODE VOLTAGE USE A HIGH VOLTAGE METER
CONNECTED FROMANODELEAD TO CHASSIS ONLY. DISCHARGE HIGH VOLTAGE TO CHASSIS
ONLY,NOT TO EXTERNAL GROUND.
WARNING: HANDLEWITH CARE HIGH VACUUM PICTURE TUBE IS DANGEROUS TO
HANDLE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. REPLACE WITH A TUBE
OF THESAME TYPE NUMBER FORCONTINUED SAFETY.
X-RAY PRECAUTION: THIS PRODUCT INCLUDES CRITICAL MECHANICAL AND
ELECTRICALPARTSWHICHARE ESSENTIAL FOR X-RADIATION SAFETY. FOR CONTINUED
SAFETY REPLACE CRITICALCOMPONENTSINDICATED IN THE SERVICE MANUALONLY WITH
EXACTREPLACEMENT PARTSGIVENIN THEPARTS LIST. REFER TO SERVICE MANUAL FOR
OPERATING HIGH VOLTAGE AT MINIMUM BRIGHTNESS, MEASUREMENT PROCEDURESAND
PROPER SERVICE ADJUSTMENTS.
1
2
3
4
5
6
7
8
MONITORLINK
TM
CONTROL
RS-232C
IR EMITTER
R
NetCommand IR
REPEATER
9
1. ANT-A, LOOP OUT and ANT-B (Antenna)
ANT-A and ANT-B receive signals from VHF/UHF antennas
or a cable system. LOOP OUT sends the ANT-A signal out to
another device, such as a cable box or VCR.
Note: LOOP OUT is disabled when Energy Mode is set to
Low.
2. Monitor Out
The Monitor Output sends the TV audio and video signals
(excluding component video, DTV video and MonitorLink) to
an A/V receiver or other equipment.
3. Inputs 1-2
These inputs can be used for the connection of a VCR, Super
VHS (S-VHS) VCR, laser disc player, or other A/V device to
the TV. With each input, you may connect to the S-VIDEO
or VIDEO terminal but not to both.
4. Component Inputs 1-2 (Component only for
WT-42413)
These inputs can be used for the connection of A/V equipment
with component video outputs, such as a DVD player or Video
Game System. Please see Appendix B, page 67, for signal
compatibility.
5. DTV Input
This input is used to connect a DTV receiver or cable box
and can be configured for HDTV component (YPbPr), or
RGB plus H&V. Please see Appendix B, page 67, for signal
compatibility.
Back Panel Input/Output for WS-, WS- & WS-
Side Panel Input/Output for WT-
6. MonitorLink/DVI
This is a Mitsubishi-exclusive proprietary digital interface for
the display of high quality digital video signals from Mitsubishi
products such as the HD-5000 HDTV Receiver/Controller.
All video signals, both analog and digital can be sent digitally
to your Mitsubushi TV from the HD-5000. This can also be
used as a DVI input for other compatible sources.
Note: The DVI-HDTV input terminal is compliant with the
EIA-861 standard and is not intended for use with personal
computers.
7. MonitorLink™ Control/RS-232C
A digital control interface that works in parallel with
MonitorLink. While MonitorLink provides the digital video
signal, MonitorLink Control provides enhanced functioning
such as automatic power ON/OFF and input selection. This
can also be used with other compatible RS-232C external
control devices. Please visit www.mitsubishi-tv.com for more
information on RS-232C command structure.-
8. IR Emitter Repeater
Connecting IR emitters here allows the TV to pass IR
commands from most IR remote controls to other A/V devices
that are out of range of the remote control. Note: This feature
is not available on the WT-42413.
. Net Command® IR Input
IR emitters connected to these jacks are used by NetCommand
system of the TV to control external analog devices such
as VCRs, DVDs, cable boxes, satellite receivers and audio
receivers. Note: This feature is not available on the WT-42413.