Projection Television Models WS-55908 and WS-65908 ® visit our website at w w w. m i t s u b is h i - t v.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USED SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
Table of Contents IMPORTANT SAFEGUARDS ............................................................................4-5 T H A Y N O K U Thank You Letter ...............................................................................................................................................8 Unpacking Your New TV...................................................................................................................................9 Special Features ..........................................
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
IMPORTANT SAFEGUARDS Continued 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
If you have questions regarding your television, call Consumer Relations at (800) 332-2119, or email us at MDEAservice@bigscreen.mea.com To order replacement or additional remote controls or owner’s guides call (800) 553-7278 or visit our website at w w w.m i t s u b ish i - t v.
Thank You Thank You Letter ............................8 Unpacking Your New TV .................9 Special Features ..............................
Part I: Thank You We at Mitsubishi Would Like to Thank You To the Mitsubishi Consumer: Thank You Letter Thank you for choosing Mitsubishi as your premier home entertainment partner. Whether this is your rst Mi tsubi shi consumer electronics product or an addition to your growing Mitsubishi family, you should be proud and delighted for choosing one of the most technologically advanced bigscreens available today.
Part I: Thank You Unpacking Your New TV Special Features Please take a moment to review the following list of items to ensure that you have received everything included: 1 Remote Control 2 (2) AAA Batteries 3 (3) IR Emitter Cables 4 Product Registration Card Owner’s Guide Quick Reference Card Your new HD-Upgradeable bigscreen television has many special features that make it the perfect addition to your home entertainment system. Below we have highlighted a handful.
U nlike typical television manufacturers, we have based our primary design and engineering capabilities in North America at our California headquarters. As a result, the engineers who design our television products live in the same communities as our customers. They know how our customers think and what their goals and desires are.
Installation Front Control Panel Functions .....12 Back Panel Functions ...................13 How Connections Affect: PIP and POP ............................... 14 System 4 Home Theater IR Control .............................. 14-15 Connecting to Your New Mitsubishi Bigscreen: Antenna or Wall Outlet Cable ...16 Cable Box ...................................16 VCR ............................................. 17 Audio Receiver...........................18 DVD Player..................................
Part II: Installation Front Control Panel (MONO) S-VIDEO VIDEO L AUDIO R CANCEL INPUT POWER CHANNEL VOLUME A/V RESET MENU ENTER INPUT-4 ADJUST Figure 1. Front Control Panel. Front Control Panel Functions IRIS™ 12 Intelligent Room Illumination (light) Sensor. Turn this feature on or off using the VIDEO button on your remote control. When the IRIS is on, your TV will automatically adjust picture contrast and brightness for the best picture based on your room lighting.
Part II: Installation Back Panel HIGH RESOLUTION INPUT 1 2 INPUT 2 3 MONITOR VGA 640X480, 60HZ 1 (YPrPb) VIDEO LOOP OUT 8 480i / 480p / 1080i Y G PIP S-VIDEO ANT-A DTV (YPrPb/GRBHV) 2 (YPrPb) 7 OUTPUT 1 STB 6 3 COMPONENT 480i / 480p ANT-B Pr R H Pb B V AUDIOLEFT/ (MONO) AUDIOLEFT/ (MONO) AUDIORIGHT AUDIORIGHT 4 IR EMITTER HOME THEATER 5 1 STB (Set-Top-Box) 2 Inputs 1-3 These inputs can be used for the connection of a VCR, Super VHS (S-VHS) VCR, laser disc player, or
Part II: Installation How Connections Affect the PIP and POP How Connections Affect the PIP and POP To see a picture in the PIP or POP inset, you may need to select an input source. If the only input connected is ANT-A, then both the main picture and the PIP/POP insert will be from that input source. If other video equipment is connected, you may be able to view these input sources as the PIP/POP insert.
Part II: Installation Special Setups: A/V Equipment (For System 4 Home Theater IR Control) VCR: Connect the cables to the TV as directed on page 17, with one exception. Connect the audio output connection to the appropriate input on the back of the A/V receiver (as shown in table 1). DTV: Connect the cables as directed on pages 20-21, with one exception.
Part II: Installation Connecting an Antenna, Wall Outlet Cable, or Cable Box UHF Antenna (Channels 14-69) VHF Antenna (Channels 2-13) Separate UHF and VHF Antennas (Figure 1) Flat Twin Lead Flat Twin Lead 1 Connecting an Antenna, Wall Outlet Cable, or Cable Box 2 Connect the UHF and VHF antenna leads to the UHF/VHF combiner. Push the combiner onto ANT-A on the TV back panel. UHF/VHF combiners are not provided with the TV. They should be available at most electronic stores.
Part II: Installation Connecting a VCR TV back panel Antennas or Wall Outlet Cable HIGH RESOLUTION INPUT COMPONENT 480i / 480p VGA 640X480, 60HZ INPUT 1 STB 1 (YPrPb) 2 MONITOR 3 ANT-A LOOP OUT (Figure 1) Pr R H Pb B VIDEO 1 480i / 480p / 1080i Y G PIP S-VIDEO Incoming Cable DTV (YPrPb/GRBHV) 2 (YPrPb) OUTPUT V AUDIOLEFT/ (MONO) AUDIOLEFT/ (MONO) AUDIORIGHT AUDIORIGHT 1 ANT-B IR EMITTER HOME THEATER 2 3 2 One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR b
Part II: Installation Connecting an Audio Receiver Stereo Audio System TV back panel HIGH RESOLUTION INPUT COMPONENT 480i / 480p VGA (Figure 1) 640X480, 60HZ INPUT 2 3 MONITOR Connecting an Audio Receiver 2 3 PIP Pr R AUDIOLEFT/ (MONO) LOOP OUT AUDIOLEFT/ (MONO) AUDIORIGHT Red ANT-B IR EMITTER HOME THEATER 1 Audio system back panel section White CD IN AUX IN IN TAPE 1 OUT IN TAPE 2 OUT L Figure 1.
Part II: Installation Do not display the same stationary images on the screen for more that 15% of your total TV viewing in one week. Examples of stationary images are letterbox top/bottom bars from DVD or other video sources, side bars when showing standard TV pictures on widescreen TV’s, stock market reports, video game patterns, station logos, web sites, or stationary computer images. Such patterns can unevenly age the picture tubes causing permanent damage to the TV.
Part II: Installation Connecting a DTV Receiver DTV Connectors and Adaptors (Figure 1) Connecting a DTV Receiver The TV back panel has 5 RCA-type connectors, for the DTV connection. The back panel of your DTV receiver may use RCAtype connectors or BNC-type connectors. If your DTV receiver comes with BNC type connections, you will need to purchase BNC to RCA adaptors to connect the TV to the DTV receiver. These adaptors should be available at most electronic supply stores.
Part II: Installation Connecting a DTV Receiver DTV Receiver with RGB Video Connections (Figure 1) 1 See Appendix B, page 61, for RGB video signal compatibility information. For digital audio connections, see your DTV receiver and A/V receiver Owner’s Guides.
Part II: Installation Connecting a Computer with a VGA Monitor Output TV back panel Connecting a Computer HIGH RESOLUTION INPUT VGA 640X480, 60HZ INPUT 1 STB Connecting a Computer and the System 4 Home Theater IR Control 2 Connect VGA Monitor Out from the computer to VGA on the TV back panel using a VGA compatible monitor cable. See Appendix B, page 61, for VGA signal compatability. Connect the L (left) and R (right) audio cables from the computer to VGA AUDIO on the TV back panel.
Part II: Installation Warning: Do not leave stationary, toolbar, or partial images on-screen for extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty. The VGA capability of this television is designed for occasional use ONLY.
W e’re proud of the many advances in digital television, in which we have played a major role. Digital broadcasting brings flawless pictures and sound. At its highest performence level, high definition television (HDTV) delivers images up to six times more detailed than standard analog television.
Setup Programming the Remote Control: To Control Other A/V Products ....... 26-27 To Activate the System 4 IR Home Therater IR Control .............. 28-29 on-screen menu system .....30 Using ...............................30 Menu Screens (Overview)....31-32 Setup Menu..............................33 Memorize Channels ..............33 Assign Input ..........................33 Language ...............................33 Closed Captions Menu ...........34 Channel Menu .........................
Part III: Setup Programming the Remote Control: To Control Other A/V Products To Program the Remote to Control Other Brands of Audio and Video Products: Programming the Remote Control: To Control Other A/V Products (Figures 1-5) 1 2 3 4 VCR 1 Move the slide switch at the top of the remote to the product you want to control. Press and hold the POWER button on the remote control. Enter the rst thr ee di gi t code li st ed for your equipment, and then release the POWER button on the remote control.
Part III: Setup Programming the Remote Control: To Control Other A/V Products CABLE/DBS/DTV TV VCR 1 DVD/LDP Player Codes DVD/LDP brand Mitsubishi (DVD) Mitsubishi (LDP) Panasonic Pioneer DVD (LDP) Sony Toshiba Code to enter: 003 016, 017 250 252 (016, 017) 254 253 To reset to default code, enter 000 POWER 2 If your DVD code is not listed here, please see page 62 for a complete listing. Figure 4. Programming the remote to control your DVD/ LDP.
Part III: Setup Programming the Remote Control: To Activate the System 4 Home Theater IR Control Activate the System 4 Home Theater IR Control Activation of the System 4 Home Theater IR Control 28 For select brands of digital A/V receiver’s, To Activate the Audio Portion: you can set up the remote control to auto(Figure 1) matically select the correct audio input when 1 Press and hold the HOME THEATER you press the HOME THEATER button. At button.
Part III: Setup Programming the Remote Control: To Activate the System 4 Home Theater IR Control Testing System 4 for Proper Setup 1 2 3 VIDEO If the TV did not change inputs... AUDIO If the A/V Receiver did not change inputs... 1 Repeat Special Setups, page 15, and retest. 2 Reposition IR emitter(s) and retest 3 Repeat To Activate the Audio Portion, page 28, and retest. If your A/V receiver is still not responding to the commands from your remote control, you may have an incompatible A/V receiver.
Part III: Setup The 3D Graphical Menu System Your TV has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on-screen information for menu choices and changes (Figure 1). A picture (icon) will be highlighted when selected with the ADJUST arrows. When selected, the appropriate menu will appear. You may then make changes within the menu or access sub-menus, if available.
Part III: Setup Menu Screens (Overview) Setup Menu (Figure 1) You can put channels in memory, turn on or off input connections of the TV, and select the menu system to display in English or Español (Spanish). Figure 1. Setup menu Display captions or text, and choose black or gray as the background color for the closed caption area. Figure 2. Captions menu Menu Screens (Overview) Captions Menu (Figure 2) Channel Menu (Figure 3) Use to customize the channel information for Ant-A and Ant-B.
Part III: Setup Menu Screens (Overview) V-Chip Lock Menu (Figure 1) Block or allow programing based upon rating signals sent by the broadcast station, or by time. Advanced Menu Figure 1. V-Chip Lock menu Menu Screens (Overview) (Figure 2) Set your TV to turn on automatically, converge (align) the three main colors, display a blue screen when viewing an input with no signal, enhance the darker parts of bright pictures, and change the line doubling method. Figure 2.
Part III: Setup Setup Menu: Memorize Channels, Assign Input, and Language Memorize Channels (Figure 1) Figure 1. Memorize Channels DTV Note: If you have a DTV receiver connected, you will need to use that receiver’s channel memorization system to memorize digital channels. Assign Input Menu (Figure 2) Assign Input turns off unused inputs, turns them on again, or changes the name of the input. If you turn an input Off, it will be skipped when you press the INPUT button on the remote control.
Part III: Setup Captions Menu: Closed Captions Captions Menu (Figure 1) Closed Captions Broadcasters can send either Standard or Text closed captioning. Standard closed captioning follows the dialogue of the characters on-screen and displays in a small section of the screen. Text closed captioning often contains information such as weather or news and covers a large portion of the on-screen program.
Part III: Setup Channel Menu: Antenna, Channel, Memory, Name, and SQV™ SQV (Super Quick View™) Using The Menu Screen (Figure 1) Figure 1. Channel menu SQV (Super Quick View™) allows you to put together a list of your favorite channels from Ant-A and Ant-B. You can store up to 6 channels in each of the 9 different memory banks. Once you have added a channel to the SQV memory, “SQV” will appear under the channel number on the TV screen.
Part III: Setup V-Chip Menu: V-Chip Lock V-Chip Lock (Figure 1) V-Chip Lock The V-Chip Lock allows you to Block or Allow programs based upon rating signals sent by the broadcasting station. The TV comes from the factory with the V-Chip lock in the Off setting. You can turn the lock On within the V-Chip Menu. The factory preset is TV-PG, allowing only programs rated TV-PG or lower. You can change the blocking level to various TV or movie ratings, lettered categories, and by time.
Part III: Setup V-Chip Menu: V-ChipLock Ant-A 002 KCBS 480i Standard Stereo SAP TV-PG DLSV SQV1 V-Chip Signal Information (Figure 1) When provided by the broadcaster, V-Chip signal information can be displayed by pressing the INFO button on the remote control. Rating guidelines are provided by broadcast stations. TV programs and made-for-TV movies can be blocked by the TV Rating and/or Categories signal. Made-for-theater and direct-to-video movies can be blocked by the Movie Rating signal. Figure 1.
Part III: Setup V-Chip Menu: V-Chip Lock Hours/Time V-Chip Lock Hours/Time (Figure 1) V-CHIP HOURS/LOCK BY TIME will allow you to activate the V-Chip or lock the entire TV during speci c hour s. V-Chip Start Time and V-Chip Stop Time (Figure 1) Figure 1. V-Chip Hours/Lock by Time menu V-Chip Lock Hours/Time Select the times you would like the V-Chip to be Active. By setting the V-Chip Start Time and V-Chip Stop Time to the same time, the V-Chip will be active 24 hours a day.
Part III: Setup Advanced Menu: Timer Timer (Figure 1) The timer will automatically turn the TV on (if it is off) at the time you schedule and select. Figure 1. Timer selection in the Advanced menu The TV’s clock must be set before you can set the timer. If you have not set the clock and/or day, you will see the CLOCK menu instead of the Timer menu. Figure 2. Timer menu Set Day (Figure 2) Select the days that the TV will turn on automatically.
Part III: Setup Advanced Menu: Convergence Convergence (Figure 1) Your Mitsubishi TV has three picture tubes which are aligned to properly converge the projected light beams on the screen. Each picture tube projects a single color of red, blue or green. During production, your TV was carefully adjusted to properly align these colors. As a special feature, you have the ability to adjust the red and blue light beams in reference to the xed gr een l ight beam. This process is called convergence. Figure 1.
Part III: Setup Advanced Menu: Advanced Convergence, Video Display, and Video Mute Advanced Convergence (Figure 1) Figure 1. Advanced Convergence screen There are more than 64 line intersections, but the ashi ng br acket w i ll onl y st op at the 64 adjustment points. Video Mute (Figure 2) Video Mute lets you display a blue or gray background when no signal is being received on inputs 1-4, and STB. Black Enhancement (Figure 2) The contrast in dark scenes is enhanced for better picture quality.
Part III: Setup Audio/Video Menu: AV Memory Reset, and Audio/Video Settings AUDIO/VIDEO SETTINGS menu (Figure 1) Each of the 11 inputs has its own A/V memory. You can adjust each input’s A/V memory in two ways. You can use the menu, or the remote control. AV Memory Reset, and Audio/Video Settings A/V Memory Reset A/V Memory Reset will return the currently selected input’s A/V memory to the factory settings.
Part III: Setup Audio/Video Menu: TV Speakers, and Audio Output TV Speakers (Figure 1) This selection will turn on or off the TV’s internal speakers. You may select Off when sending the sound through a separate stereo system or surround sound A/V receiver. Figure 1. Audio/Video menu To prevent damage from a sudden increase in volume, make sure the TV volume is low before choosing ON. (Figure 1) Select Fixed if your audio receiver or stereo system can be controlled with a remote.
Part III: Setup Clock Menu: Clock Setting (Manual) Clock Setting (Manual) (Figure 1) For the manual clock setting, select the current time, including AM or PM. Press or to slowly adjust the time. Press and hold or to quickly adjust the time. Figure 1. Clock menu (Manual) Set Day Clock Setting (Manual) (Figure 1) 44 When Manual has been selected for the Clock Setting, you need to select the current day of the week.
Part III: Setup Clock Menu: Clock Setting (Auto) Clock Setting (Auto) (Figure 1) Setting the Clock Setting to Auto will automatically set the day and time using Extended Data Service (XDS) time data. This data is automatically retrieved from a PBS channel or other channel carrying this service. Figure 1.
Part III: Setup A/V Setting Descriptions: Audio Audio Settings Bass enhances or reduces low frequency sound. Treble enhances or reduces high frequency sound. Balance adjusts the level of sound between the left and right speakers. A/V Setting Descriptions: Audio Surround creates simulated stereo and surround effects. Your choices are: 46 • Off: No surround effects. Use this setting when using an A/V receiver with Dolby™ Pro Logic Surround, or Dolby™ Digital Surround.
Part III: Setup A/V Setting Descriptions: Video Video Settings IRIS™ is the Intelligent Room Illumination (light) Sensor. When IRIS™ is on, your TV will automatically adjust picture contrast and brightness for best quality (Contrast and Brightness cannot be adjusted manually). Brightness provides a slider to adjust the overall brightness of the picture. Sharpness provides a slider to adjust the detail and clarity. Color provides a slider to adjust the color intensity.
E ver wish you were actually part of the movie or sitting in a field-level box at the 50-yard line, watching the game? The Mitsubishi total home theater system is the next best thing to being there. A home theater immerses you in both video and audio to a point of surrealism. The core of the home theater system is your bigscreen television, the biggest one your room can accommodate.
Operation Remote Control Functions...... 50-57 Overview.....................................50 Care and Operation ...................51 Channel Selection .......................52 Sleep Timer ................................52 System 4 Home Theater IR Control ...................................53 Special Functions ......................54 Operation of PIP and POP... 54-55 Display Formats ................... 56-57 IMPORTANT NOTES #2.................
Part IV: Operation Remote Control Functions: Overview Overview (Following page, gur e 1) 1 2 3 4 5 Overview 6 7 8 9 10 11 12 13 14 15 16 50 Slide Switch: Select A/V product to be controlled by the remote control. Numbers: Individually select channels or input information into TV. POWER: Turns power on and off for TV and other A/V products. SQV (Super Quick View™): Scan through a memorized list of favorite channels. QV (Quick View™): Switch to last channel viewed.
Part IV: Operation Remote Control Functions: Care and Operation Operation VCR CABLE/DBS/DTV TV 1 (Figure 2) 1 2 3 4 5 6 8 9 0 QV 5 2 7 4 SQV INPUT POWER 3 12 6 7 SLEEP 14 CANCEL 17 10 Remove the remote control’s back cover by gently pressing the ridged tab in the direction of the arrow and sliding off the cover. Load the batteries, making sure the polarities (+) and (-) are correct.
Part IV: Operation Remote Control Functions: Channel Selection and Sleep Timer Channel Selection Sleep Timer For Non-DTV Channels: Setting the Sleep Timer: Enter three numbers (for channel 2, press 002). or Press the channel number and ENTER (for channel 2, press 2, then ENTER). Channel Selection and Sleep Timer or Enter the channel number and wait four seconds. The TV will change automatically. Canceling the Sleep Timer: Press SLEEP to display the on-screen message.
Part IV: Operation Remote Control Functions: System 4 Home Theater IR Control Requirements for Operation System 4 allows for only one of the following: • Cable Box • Satellite Receiver • Digital TV Receiver Operation (VCR as example) To watch your VCR: 1 Turn on the TV and A/V Receiver. 2 Move slide switch to VCR. 3 Point remote at the TV and press the HOME THEATER button. 4 The TV and A/V Receiver should change to the appropriate inputs. 5 Operate the VCR.
Part IV: Operation Special Functions and Operation of PIP and POP Remote Control Functions: Special Functions When your remote control has been Programmed to operate another manufacturer’s product, the function performed on each layer can vary.
Part IV: Operation Remote Control Functions: Operation of PIP and POP Changing PIP/POP Inputs 1 MAIN PICTURE Side-by-Side Press PIP INPUT to cycle through available inputs. To see which inputs can and cannot be used together, see How Connections Affect the PIP and POP - Table 1, page 14. Changing PIP/POP Channels Press PIP CH to scroll up and down through memorized channels on Ant-A, and Ant-B.
Part IV: Operation Remote Control Functions: Display Formats This is a wide screen TV (also known as a 16:9 TV). This shape re ect s t he new types of images available from HDTV and many DVDs. There are still many older style narrow screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats to choose from.
Part IV: Operation Anamorphic Widescreen Picture (16:9) 1 1 2 2 3 3 4 4 5 5 Display Formats Non-Anamorphic Picture (4:3) 57
Part IV: Operation Warning: Do not leave stationary or letterbox images on-screen for IMPORTANT NOTES #2 extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty. 58 The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should ll the screen with constantly moving images rather than stationary images or patterns.
Appendix A: Bypassing the V-Chip Lock Appendix A: Bypassing the V-Chip Lock Lock Bypass Instructions Have Been Filed for Future Reference Bypassing the V-Chip Lock After you set the lock, you need your passcode to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip lock menus. When entering the V-Chip Lock menu, this process deletes your old passcode and prompts you to enter a new passcode.
Appendix B: High Resolution Input Connection Compatiblity Component-1 and Component-2 Inputs VGA Input This input will accommodate most computers capable of supporting a VGA monitor. The only compatible display resolution is 640x480. The sync rate is 60hz. SVGA and XVGA resolutions are not supported. DTV Input This input is compatible with most standard DTV receivers with component video outputs. Compatible DTV signals are SDTV 480i, 480p, and HDTV 1080i.
Appendix C: Remote Control Programming Codes Appendix C: Remote Control Programming Codes A/V Receivers 62 Mitsubishi . .. .. . .. .. .. .. .. Admiral . .. .. .. Aiwa. .. .. .. .. Denon . .. .. .. Fisher . .. .. .. Gerrard . .. .. .. Harman Kardon . Jensen . .. .. .. JVC . .. .. .. .. Kenwood . .. .. Magnavox . .. .. Marantz . .. .. Mclintosh . .. .. Nakamichi . .. .. Onkyo . .. .. .. Optimus . .. .. Panasonic . .. .. Philips . .. .. .. Pioneer . .. .. .. Quasar . .. .. .. RCA . .. .. .. .. Sansui . ..
Appendix D: Cleaning and Service Cleaning Service Normally, light dusting with a dry, nonscratching duster will keep your TV clean. Use care when cleaning your TV with any other product. If you want to gently wipe down your TV with a lightly moistened soft cloth, rst tur n of f and unpl ug your TV. You can add a few drops of mild liquid detergent to the water for oily dirt.
Appendix E: Troubleshooting Appendix E: Troubleshooting 64 Problem Possible Solution • The TV remote control does not work. • Check that the batteries are installed correctly. • Check that the selected switch is set to “TV”. • Be no further than 20 feet from the TV when using the remote control. • The TV takes several seconds to respond to channel commands. • Press ENTER after a channel number to avoid delays. • Use the three digit number, i.e 002 for channel 2. • You cannot access a channel.
Index A adding and deleting channels 35 Advanced Features menu 39 adaptors (BNC to RCA), 20 adjusting (convergence), 40-41 alignment (convergence), 40-41 antennas (connecting), 16 assistance, 63 audio settings 46 B back panel, 13 balance, 46 bass, 46 Black Enhancement, 41 blocking (enabling V-Chip), 36-38 brightness, 12, 47 bypassing (parental lock), 59 cleaning, 4, 63 Clock (setting), 44-45 compatibility (signal), 61 contrast, 12, 47 convergence, 40-41 D date (setting), 39, 44-45 daylight savings ti
Index S Index S-W safeguards, 4-5 servicing, 2, 5, 63 signal types 1080i, 56, 61 480i, 41, 61 480p (progressive DVD), 41, 61 720p, 61 960i, 41 Sleep Timer, 52 sound (adjusting), 46 Spanish, 33 Special Functions, 54 SQV (Super Quick View™), 35 stand, 4 STATIONARY PICTURE WARNING, 19, 23, 58 surface, 4, 63 surges, 5 T time (setting), 44-45 Timer (turn TV on), 39 Timer (Sleep), 52 treble, 46 Troubleshooting, 64 TV speakers, 43 U unpacking, 9 upgradeable, 9 66 V V-Chip Lock, 36-38 bypassing, 59 entry
Mitsubishi Projection TV Limited Warranty MITSUBISHI PROJECTION TELEVISION LIMITED WARRANTY MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this television that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material: a. Parts. The lenticular (i.e. front picture) screen and/or the DiamondShield™ is warranted against defects in materials and workmanship for a period of 30 days.
If you have questions regarding your television, call Consumer Relations at (800) 332-2119, or email us at M D E A s e r v i c e @ b i g s c r e e n . m e a . c o m To order replacement or additional remote controls or owner’s guides call (800) 553-7278 or visit our website at w w w.m i t s u b ish i - t v.c o m © 2001 Mitsubishi Digital Electronics America, Inc. 871D297A30 Designed and Printed in the U.S.A.
