ENGLISH EN DATA PROJECTOR MODEL XD110U/XD110R SD110U/SD110R User Manual This User Manual is important to you. Please read it before using your projector.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of suffcient magnitude to constitute a risk of electric shock.
Important safeguards................................................................................................................................4 Overview...................................................................................................................................................6 Remote control .........................................................................................................................................8 Installation ......................................
Important safeguards Please read all these instructions regarding your projector and retain them for future reference. Follow all warnings and instructions marked on the projector. 1. Read instructions All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions The safety and operating instructions should be retained for future reference. 3. Warnings All warnings on the appliance and in the operating instructions should be adhered to. 4.
Do not touch the air outlet grilles and bottom plate. Unplug immediately if there is something wrong with your projector. Do not touch them or put other equipment close to the air outlet grilles because they become hot during operation. The heated air outlet grilles and bottom plate may cause injury or damage to other equipment. Also, do not put the projector on a desk that is easily affected by heat. Do not operate if smoke, strange noise or odor comes out of your projector.
Overview 2 3 1 1 FOCUS ring 2 ZOOM ring 3 Control panel 4 Air outlet grille 5 Remote control sensor (Front) 6 Air inlet grille 7 Air inlet grille 8 Terminal board 9 Kensington Security Lock Standard connector 10 Air inlet grille 4 12 5 11 Speaker 10 12 Adjustment feet (front) 13 Adjustment feet (rear) 14 Hook for banding 14 11 7 9 8 6 13 Control panel 2 3 8 9 7 4 1 1 Power button 2 AUTO POSITION / S button 3 COMPUTER / W button 4 MENU button 5 STATUS indicator
3 1 Lamp cover 2 Adjustment feet (rear) 3 Adjustment feet (front) ENGLISH Bottom side Caution: Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
Remote control Battery installation Use two AAA size batteries. 1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow. 2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -). • Load the batteries from - spring side, and make sure to set them tightly. 3. Replace the back cover. Caution: • • • • • • • • • • Use of a battery of wrong type may cause explosion.
Installation Layout of the projector ENGLISH Image size varies depending on the distance between the screen and the projector. Front projection W B Hd H A A=B L L : Between the screen and the front edge of the projector Hd : Height of the projected image Screen Diagonal size • Distance from the screen : L Width : W Height : H MINIMUM Zoom (WIDE) MAXIMUM cm inch cm inch cm inch m inch m inch cm inch cm 40 102 32 81 24 61 50 1.3 61 1.5 3.5 8.8 10.7 27.
Basic connections This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that have analog RGB output connectors. Important: • • • • Make sure that the connected device is turned off before starting connection. Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the cord.
ENGLISH Projector + Computer For computer with Mini D-SUB RGB cable for PC COMPUTER IN Computer to monitor port AUDIO IN AUDIO OUT MONITOR OUT AUDIO OUT Audio cable (option) Necessary when outputting to both a PC monitor and the projector. MONITOR OUTPUT RGB cable for PC (option) to PC audio output PC audio cable (option) Important: • • • • • When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly.
Preparation Preparation for projection 1. 2. 3. Attach the provided power cord to the projector. Plug the power cord in the wall outlet. Remove the lens cap. Warning: • • • • • • • • Do not look into the lens directly when the projector is on. The lens cap is for protecting the lens. If you leave the lens cap on the lens with the projector turned on, it may be deformed because of heat build-up. Remove the lens cap when you turn on the projector. The power cords for use in the U.S.
ENGLISH Basic operation 4 3 6 5 5 3, 1, 2 Power-on 1. 2. 3. 5. Turn on the device connected to the projector first. Plug the power cord in the wall outlet. • The POWER indicator lights up. • If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may start rotating when the power cord is plugged in next time and the POWER button may not function. In this case, wait for the fans to stop and press the POWER button to light the indicator.
Basic operation (continued) Power-off Volume from the speaker Use the following procedure to turn off the projector. 1. Press the POWER button on the control panel or the OFF button on the remote control. • The message "POWER OFF? YES : PRESS AGAIN" appears on the screen. • To cancel, press any button except the POWER button. (Some buttons on the remote control don’t function for cancel.) 2. Press the POWER button on the control panel or the OFF button on the remote control within 10 seconds again.
IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE COLOR TEMP.
Menu operation (continued) 1 IMAGE CONTRAST ................................................Use to adjust the image contrast. The contrast becomes opt. XGA60 higher as the value increases. BRIGHTNESS.............................................Use to adjust the image brightness. The image becomes IMAGE brighter as the value increases. CONTRAST 0 WHITE ENHANCE......................................Use to adjust the white level of the projected image. BRIGHTNESS 0 Select AUTO for normal use.
MENU POSITION ...................................... Use to select the position of the menu on the screen, 1. opt. XGA60 (upper left) or 2. (lower right). CINEMA MOD............................................ When AUTO is selected, the film mode will be automatiFEATURE cally activated when a film source signal is inputted. MENU POSITION 1. When OFF is selected, the film mode will not be actiAUTO CINEMA MODE vated. ? AUTO VIDEO SIGNAL VIDEO SIGNAL..........................................
Image adjustment Image adjustment Color temperature You can adjust the image using the IMAGE menu. 1. 2. 3. opt. XGA60 IMAGE Select COLOR TEMP. in the IMAGE menu. Press the W or X button to select USER . Press the ENTER button. USER CONTRAST 0 CONTRAST R 0 BRIGHTNESS 0 CONTRAST B 0 WHITE ENHANCE COLOR TEMP. AUTO BRIGHTNESS R 0 STANDARD BRIGHTNESS B 0 COLOR 0 TINT 0 SHARPNESS GAMMA MODE 0 AUTO 4. 5. 6. 7. Press the S or T button to select the desired item.
Simple adjustment method This projector adjusts the format of the video signal supplied from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When the image from the computer isn’t projected correctly, press the AUTO POSITION button. (See page 14.) If the image isn’t projected correctly yet, adjust the image from the computer using the menu. 1. 2. opt. XGA60 SIGNAL R RG GB B HORIZ. POSITION 0 VERT. POSITION 0 FINE SYNC.
Advanced feature Still To stop the motion in the image temporarily (or to display a still image): Press the STILL button on the remote control. • The image will freeze temporarily. To resume the motion in the image: Press the STILL button on the remote control again. Important: • Do not display a still picture for a long time because the afterimages may persist on the screen. Page-up and page-down You can control the computer to page-up and page-down the presentation data using the remote control.
To cancel the password function: This projector is equipped with the password function that is designed for prevention of wrong operation by children and restriction on operation by other than specified users. MENU ACCESS ............All the buttons except for the POWER button on the projector are disabled. (The buttons on the remote control are enabled.) You can use this mode as a measure of prevention of wrong operation by children and restriction on operation by other than specified users. 1. 2. 3.
Lamp replacement When the lamp no longer functions, replace it with a new one. 9. Caution: • • • • • • • • • 1. 2. 3. 4. 5. 6. 7. 8. Do not remove the lamp immediately after using the projector. You may get burned because the lamp very hot after use. Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for lamp to cool down. Unplug the power cord from wall outlet and wait one hour for the lamp to cool down completely.
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your dealer. Images aren’t projected on the screen. Problem Cause and solution • Check the states of the indicators. POWER STATUS Off Off Solution Connect the power cord to the projector. Plug the power cord into a wall outlet. If any objects are blocking the air inlet or outlet grille, remove them and carry out the following. Off 1. 2. 3. 4.
Troubleshooting (continued) Images aren’t projected correctly. Problem Projected images are shaking. Projected images are displaced. Cause and solution • • • • Check that the cable connected to the external device isn’t intermittent. Connect the cable’s plug with the external device’s connector firmly. Press the AUTO POSITION button. Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu. (See page 19.) Projected images are distorted.
Problem ENGLISH Others Cause and solution Hot air is emitted from the air outlet grilles. • This air comes out as a result of cooling the inside of the projector. This isn’t a product malfunction. No audio is output. • Check that the volume isn’t set to low. • The microcomputers inside the projector may be wrongly operating because of noise. J Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.
Indicators This projector has two indicators, each of which shows the operation condition of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer. STATUS indicator POWER indicator Normal condition POWER STATUS Steady red Off Steady green Blinking green Steady green Steady green CONDITION NOTE Stand-by Lamp stand-by (about 1 minute) The POWER button cannot be used to switch between on and off.
Specifications • DLP™ DATA projector Model XD110U/XD110R/SD110U/SD110R Rated power supply 100 - 240 V AC, 50 / 60 Hz Rated input 2.9 A Display Technology 0.55-inch Single chip Digital Micromirror Device (DMD) with R,G,B,W color wheel Pixels 1024 x 768 = 786432 pixels (XD110U/XD110R) Pixels 800 x 600 = 480000 pixels (SD110U/SD110R) Colors 16770000 colors ENGLISH Type Projection lens F 2.4- 2.6 f = 18 - 21.
Specifications (continued) Connectors COMPUTER IN/OUT (Mini D-SUB 15-pin) 11 15 10 6 1 IN pin No. Spec. pin No. Spec.
Signal mode TV60, 480i(525i) resolution (H x V) horizontal frequency (kHz) vertical frequency (Hz) XD110U/XD110R (H x V) SD110U/SD110R (H x V) - 15.73 59.94 1024 x 768 800 x 600 TV50, 576i(625i) - 15.63 50.00 1024 x 768 800 x 600 1080i 60 (1125i 60) - 33.75 60.00 1024 x 576 800 x 450 1080i 50 (1125i 50) - 28.13 50.00 1024 x 576 800 x 450 480p (525p) - 31.47 59.94 1024 x 768 800 x 600 576p (625p) - 31.25 50.00 1024 x 768 800 x 600 720p 60 (750p 60) - 45.00 60.
MITSUBISHI Projector Contact Information North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquires Phone :+1-(800) 450-6487 Fax :+1-(905) 475-7958 E-mail :projectors@mitsubishielectric.ca Customer Care E-mail :support@mitsubishielectric.ca MDEA (Mitsubishi Digital Electronics America, Inc.) (Warranty Registration) http://www.mitsubishi-presentations.
