1PS41(MMNA)_Cover2.fm 1 ページ 2010年2月19日 金曜日 午後3時22分 Introduction N09200100846 Thank you for buying a MITSUBISHI GALANT. We are confident you will enjoy your vehicle. It has been engineered for optimum performance, durability and comfort. By thoroughly reading this Owner’s Manual, you will gain an understanding of the many features that are included in the GALANT. The Owner’s Manual contains descriptions and illustrations that will assist in the operation and maintenance of your vehicle.
BK0121200US.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Overview Instruments and controls N00100201202 Instrument cluster P.3-72 Combination headlights and dimmer switch P.3-81 Turn signal lever P.3-84 Steering wheel remote control switch (if so equipped) P.5-62 Supplemental restraint system - air bag (for driver’s seat) P.2-38 Horn switch P.3-91 Wiper and washer switch P.3-87 Ignition switch P.3-34 Cruise control lever P.3-57 Fuses P.7-35 Engine hood release lever P.
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Overview Selector lever P.3-39 Supplemental restraint system - air bag (for front passenger’s seat) P.2-38 Heated seat switch (if so equipped) P.2-10 Parking brake lever P.3-28 Floor console box/ Tissue holder/Pen holders P.3-132 Glove compartment P.3-131 Auxiliary Audio connector* P.5-60 Trunk lid release lever P.3-16 Power outlet P.3-122 Cup holder P.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Overview Center panel N00100700141 Passenger’s air bag off indicator P.2-46 Vents P.5-2 Audio system P.5-24, 5-37 Front passenger seat belt warning light P.2-21 Hazard warning flasher switch P.3-85 Electric rear window defogger switch P.3-90 Air conditioning P.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Overview Interior N00100301014 Outside rearview mirror switch P.3-32 Power window switch P.3-23 Dome light P.3-129, 7-46, 7-59 Sunroof switch (if so equipped) P.3-26 Reading lights P.3-128, 7-46, 7-59 Hands-free Bluetooth® cellular phone interface system with voice recognition (if so equipped) P.3-92 Inside rearview mirror P.3-30 HomeLink ® Wireless Control System (if so equipped) P.3-124 Supplemental restraint system curtain air bag P.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Overview Trunk area N00100400252 Jack P.6-8 Luggage hooks P.3-134 Luggage hooks P.3-134 Spare tire P.6-10 Tools P.6-8 Inside emergency trunk lid release handle P.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Overview Outside N00100601222 Windshield wiper and washer P.3-87 Outside rearview mirrors P.3-32 Engine compartment P.7-6 Engine hood P.7-4 Fuel tank filler door P.1-4 Locking and unlocking P.3-12 Keyless entry system P.3-7 Front fog lights (if so equipped) P.3-86, 7-45, 7-51 Front side-marker lights P.3-81, 7-45, 7-50 Headlights P.3-81, 7-45, 7-47 Front turn-signal and parking lights P.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Overview Back-up lights P.7-45, 7-54 Rear-view camera (if so equipped) P.3-69 Satellite radio antenna (if so equipped) P.5-71 Antenna P.5-71 Tail and stop lights P.3-81, 7-45, 7-53 Rear side-maker lights P.3-81, 7-45, 7-53 High-mounted stop light P.7-45, 7-56 Trunk lid P.3-16 License plate light P.3-81, 7-45, 7-57 Rear turn-signal lights P.3-84, 7-45, 7-53 Tire inflation pressure P.7-23 Changing tires P.6-9 Tire rotation P.7-25 Tire chains P.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Quick index If this warning light comes on or flashes while you’re driving... N00200701006 NOTE ● These warning lights will come on for a few seconds for a bulb check when the ignition key is first turned to “ON”. Warning light Do this Ref. page ● Park your vehicle in a safe place and stop the engine. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. P.
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Quick index Warning light “N” indicator in the instrument cluster flashes rapidly (twice per second) or Engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) or Anti-lock braking system warning light SRS warning light 2 Do this Ref. page ● Park your vehicle in a safe place. Idle the engine until the “N” indicator goes off.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Quick index Warning light “N” indicator in the instrument cluster flashes slowly (once per second) and ASC indicator and ASC OFF indicator Tire pressure monitoring system warning light Do this Ref. page ● Have the automatic transaxle checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. P.3-42 ● Park your vehicle in a safe place and turn off the engine.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Quick index If you hear this sound... N00200800648 Sound Constant tone when the driver’s door is opened. 4 Do this Ref. page “Key reminder buzzer” A tone will sound if the driver’s door is opened while the ignition key is in the “LOCK” or “ACC” position. Remove the key to stop the tone. OR P.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Quick index Sound Do this Ref. page Metallic squeal when you press the brake pedal while driving. “Brake pad wear alarm” The brake pads are worn down to the serviceable limit. Have the brake pads replaced at an authorized Mitsubishi Motors dealer or a repair facility of your choice. P.3-48 Tone when the ignition key is turned to the “ON” position.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Quick index If this problem occurs... N00200900694 Problem Do this Ref. Page Cannot turn the key. From “LOCK” to “ACC” Turn the key while jogging the steering wheel in either direction. From “ACC” to “LOCK” Check the position of the selector lever. The key cannot be removed unless the selector lever is set to the “P” (PARK) position. Cannot shift the selector lever Shift the selector lever while pressing the brake pedal. from the “P” (PARK) position.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Quick index Problem Do this Ref. page The engine coolant temperature gauge indicator is at the “H” (hot) position. Steam comes out of the engine compartment. The vehicle is stuck in sand, mud, or snow. ! The engine is overheated. Carefully stop the vehicle in a safe place. P.6-5 Move the selector lever rhythmically between “Sports Mode” and “R” (REVERSE) positions, while pressing lightly on the accelerator pedal. P.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Quick index Problem Do this The brakes are not functioning properly after driving through Dry out the brakes by driving slowly while lightly pressing the brake pedal. water. The automatic transaxle does not shift when accelerating and/or the vehicle does not easily begin to move. There may be a problem in the automatic transaxle. Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 General information Fuel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Filling the fuel tank . . . . . . . . . . . . . . . . . . . . . . . .1Modification of your vehicle . . . . . . . . . . . . . . . . .1Mitsubishi Motors genuine parts . . . . . . . . . . . . . .1California Perchlorate Materials Requirements. . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 General information Fuel selection Octane requirement N00301000794 Your vehicle is designed to use unleaded gasoline only. It is equipped with a fuel filler tube especially designed to accept only a small diameter unleaded gasoline dispensing nozzle. 1 ! WARNING ● Gasoline is highly flammable and explosive. You could be burned, seriously injured or killed when handling it.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 General information MMT (methylcyclopentadienyl manganese tricarbonyl) MMT is a manganese-containing metallic additive that is blended into some gasolines to increase the octane number. Mitsubishi Motors Corporation recommends using gasolines without MMT. Use of gasolines blended with MMT may adversely affect performance, and cause the malfunction indicator on your instrument panel to come on.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 General information Filling the fuel tank Fuel tank capacity N00301100883 ! 1 WARNING ● Gasoline is highly flammable and explosive. You could be burned, seriously injured or killed when handling it. When refueling your vehicle, always turn the engine off and keep away from flames, sparks, and smoking materials. Always handle fuel in well-ventilated outdoor areas.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 General information 3. Open the fuel tank filler pipe by slowly turning the cap counterclockwise. 4. To fill with fuel correctly depends mainly on correct handling of the fuel filler nozzle. Do not tilt the nozzle. Insert the nozzle in the tank port as far as it goes. ! CAUTION ● Your vehicle can only be operated using unleaded gasoline.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 General information ! CAUTION ● If you need to replace the fuel tank filler pipe cap, use only the cap specified for your model vehicle. NOTE 1 ● If the fuel tank filler pipe cap is not tight while driving, the engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) may come on when the onboard diagnostic (OBD) system performs a self check. Always tighten the fuel tank filler pipe cap until you hear clicking sounds.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 General information Installation of accessories N00301700179 ! CAUTION ● Before any electrical or electronic accessories are installed, consult an authorized Mitsubishi Motors dealer. ● The installation of accessories, optional parts, etc., should only be carried out within the limits prescribed by law in the driving area and in accordance with the guidelines and warnings contained within the documents accompanying this vehicle.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 General information Modification/alterations to the electrical or fuel systems N00301800040 1 Mitsubishi Motors manufactures high quality vehicles with an emphasis on safety. It is important that any accessory that is to be fitted, or any modifications carried out which involve the electrical or fuel systems, should be carried out in accordance with Mitsubishi Motors guidelines.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 General information California Perchlorate Materials Requirements N00300100017 Certain components of this vehicle, such as airbag modules, seat belt pretensioners, and button cell batteries, may contain perchlorate materials. Special handling may apply. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate.
BK0121200US.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Seats and restraint systems. . . . . . . . . . . . . . . . . . .2Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Rear seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seats N00408400437 2 1 - Front seats To adjust the seat forward or backward → P.2-5 To adjust the seatback → P.2-6 To adjust the seat height (Driver’s side only) → P.2-8 To adjust the lumbar support (Driver’s side, Power seat only) → P.2-10 ● Heated seats (if so equipped) → P.2-10 ● ● ● ● 2-2 2 - Rear seat ● Arm rest → P.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seats and restraint systems N00401600052 Your vehicle has seat belts and other features that help protect you and your passengers in an accident. Seat belts are the most important safety device. When worn properly, seat belts can reduce the chance of serious injury or death in various types of crashes.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Front seats N00401800360 Position the driver’s seat as far back as possible while maintaining a position that still enables you to fully apply the pedals, easily control the steering wheel and safely operate the vehicle. Manual seat 2 2-4 Power seat ! WARNING ● Do not attempt to adjust the seat while driving. This can cause loss of vehicle control and result in an accident.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! CAUTION ● Make sure that the seat is adjusted by an adult. If it is adjusted by a child, an unexpected accident might occur. ● Do not place a cushion or the like between your back and the seatback while driving. The effectiveness of the head restraints will be reduced in the event of an accident. ● When sliding the seats, be careful not to catch your hand or leg.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Power seat Push the switch to adjust the seat forward or backward to the desired position. Release the switch, and the seat will lock at that position. To adjust the seatback N00402000330 Manual seat To adjust the seatback, lean forward slightly, gently pull the seatback lock lever up, then lean backward to a comfortable position and release the lever. The seatback will lock in place.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Power seat Adjust the seatback angle by operating the switch as indicated by the arrows. ! WARNING ● To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehicle is in motion. Seat belt performance during an accident can be adversely affected if the seatbacks are reclined.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems To adjust the seat height (Driver’s side only) Power seat Manual seat Front and/or rear parts of the seat cushion height can be adjusted. Turn the dial to raise or lower the whole seat cushion. NOTE N00402100227 ● To prevent the battery from running down, operate the power seat with the engine running. Front part of the seat cushion Operate the switch to raise or lower the front part of the seat cushion.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Rear part of the seat cushion Operate the switch to raise or lower the rear part of the seat cushion. Whole seat cushion Operate the center of the switch to raise or lower the whole seat cushion.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems To adjust the lumbar support (Driver’s side, Power seat only) N00402200156 A lumbar support is included in the seatback of the driver’s seat. Heated seats (if so equipped) N00435600206 The heated seats can be operated when the ignition key is in the “ON” position.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! Rear seat CAUTION ● Switch off the seat heaters when not in use. Operate the heaters at high for quick heating. After the seat has become warm, set the heater to low to keep it warm. Slight variations in the seat temperature may be felt while using the heated seats. This is caused by the operation of the heater’s internal thermostat and does not indicate a malfunction.
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Head restraints Trunk-through lid N00409000023 Open the lid to gain access to the luggage compartment from the cabin. This feature is useful for storing and removing small items. Fold down the armrest, then open the lid. 2 2-12 N00404300555 Padded head restraints for the seats can reduce the risk of a whiplash injury if your vehicle is hit from the rear. The head restraints are equipped in the illustrated position.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● In order to minimize the risk of a neck injury due to a rear impact, the seatback must be adjusted to the upright position and the head restraint must be adjusted to the proper position before vehicle operation. The driver should never adjust the seat while the vehicle is in motion. ● Driving without the head restraints in place can cause you and your passengers serious injury or death in an accident.
BK0121200US.book 14 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems To remove Press the lock knob (A) in the direction shown by the arrow. Then pull the head restraint up and out of the seatback. 2 ! WARNING ● To help minimize the risk of neck injury in the event of an accident, the head restraints must be properly installed and positioned to proper height before vehicle operation.
BK0121200US.book 15 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! Seat belts CAUTION ● Always use the correct head restraint provided for the seat and do not install the head restraint in the wrong direction. N00406000282 Seat belts are installed in your vehicle to help reduce the risk of injury to the driver and passenger in the event of an accident. Always use the provided seat belts. Carefully review the following information for proper seat belt usage.
BK0121200US.book 16 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! 2 WARNING ● To reduce the risk to a front seat passenger of serious injury or death from a deploying air bag, make sure the passenger always wears the seat belt properly, remains seated all the way back and upright in their seat, and moves the seat as far back as possible. Refer to “Supplemental Restraint System (SRS) air bag” on page 2-38 for additional information.
BK0121200US.book 17 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seat belt instructions N00406200330 All seats are equipped with a seat belt which uses one combined lap-and-shoulder belt with an emergency locking retractor. This system is designed to provide both comfort and safety. It permits full extension and automatic retraction of the belts during normal vehicle operation.
BK0121200US.book 18 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehicle is in motion. Seat belt performance during an accident can be adversely affected if the seatbacks are reclined. The more a seatback is reclined, the more likely seat belt performance will be adversely affected.
BK0121200US.book 19 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems 3. Pull the seat belt out slowly while holding the latch plate. Push the latch plate into the buckle until you hear a “click”. Pull up on the belt to be sure the latch plate is locked securely in the buckle. 4. The lap part of the belt must always be worn low and snug across the hips. Pull up on the shoulder portion of the belt to take up any slack in the lap belt.
BK0121200US.book 20 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems NOTE 2 ● With the exception of the seat belt for the driver, the seat belts in all other seating positions are equipped with an Automatic Locking Retractor (ALR) function. If you pull the seat belt fully out of the retractor, the retractor will switch to its ALR child restraint installation function (see page 2-34). When the ALR function has been activated, the seat belt will only retract.
BK0121200US.book 21 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● In order to reduce the risk of serious injury or death in an accident, always wear your own seat belt. Do not allow anyone to ride in your vehicle unless he or she is also seated and wearing a seat belt. Children should additionally be restrained in a secure child restraint system.
BK0121200US.book 22 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Adjustable seat belt shoulder anchor (front seats) N00406300083 To move the anchor down, press the lock knob (A) and slide the anchor down to the desired position. To move the anchor up, slide the anchor up to the desired position. Anchor down 2 2-22 Anchor up ! WARNING ● Always adjust the shoulder belt anchor so that the shoulder belt is positioned across the center of your shoulder without touching your neck.
BK0121200US.book 23 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seat belt guide (rear seat) Installation N00419300029 The seat belt guide for the rear seat outside positions will provide added seat belt comfort for children who have outgrown child restraints and for small adults. When the shoulder seat belt is inserted through the seat belt guide, the seat belt guide better positions the seat belt webbing away from the neck and head of an occupant. 1.
BK0121200US.book 24 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems 2. Make sure the elastic cord (C) of the seat belt guide passes behind the seat belt webbing. 2 ! CAUTION ● Make sure the part of the seat belt webbing you inserted into the seat belt guide is not twisted. Twisted webbing may adversely affect seat belt performance. 2-24 3. Fasten the seat belt and make sure it fits snugly across your shoulder. Refer to “Seat belt instructions” on page 217.
BK0121200US.book 25 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seat belt use during pregnancy Seat belt extender N00406700104 When your seat belt, even fully extended, is not long enough, a seat belt extender must be obtained. The extender may be used for either of the front seats. N00406800088 Seat belts work for everyone, including pregnant women. Like all occupants, pregnant women are more likely to be seriously injured or killed in an accident if they do not wear seat belts.
BK0121200US.book 26 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Seat belt pre-tensioner and force limiter systems The seat belt pre-tensioner system includes the following components: N00417700175 The driver’s and front passenger’s seats each have a seat belt equipped with a pre-tensioner system. Pre-tensioner system 2 The driver and front passenger seat belts are equipped with a seat belt pre-tensioner system.
BK0121200US.book 27 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems When the seat belt pre-tensioners activate, some smoke is released and a loud noise will be heard. The smoke is not harmful, but care should be taken not to intentionally inhale it, as it may cause some temporary irritation to people with respiratory problems. Even in the event of a severe frontal impact, the pre-tensioners will not operate if the seat belts are not fastened.
BK0121200US.book 28 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Child restraints N00407100668 2 When transporting infants or small children in your vehicle, an appropriate child restraint system must always be used. This is required by law in the U.S. and Canada. Child restraints specifically designed for infants and small children are offered by several manufacturers.
BK0121200US.book 29 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● Never hold an infant or child in your arms or on your lap when riding in this vehicle, even when you are wearing your seat belt. Never place any part of the seat belt you are wearing around an infant or child. Failure to follow these simple instructions creates a risk of serious injury or death to your child in the event of an accident or sudden stop.
BK0121200US.book 30 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● FRONT-FACING CHILD RESTRAINTS should always be used in the rear seat whenever possible. If one must be used in the front passenger seat, move the seat to the most rearward position and make sure the child stays in the child restraint, properly restrained. Failure to follow these instructions could result in serious injury or death to the child.
BK0121200US.book 31 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems NOTE ● Before purchasing a child restraint system, try installing it in the rear seat to make sure there is a good fit. Because of the location of the seat belt buckles and the shape of the seat cushion, it may be difficult to securely install some manufacturer’s child restraint systems.
BK0121200US.book 32 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Tether anchor locations N00418900161 Your vehicle has 3 attachment points on the rear shelf, located behind the top of your rear seat. These are for securing a child restraint system tether strap to each of the 3 rear seating positions in your vehicle.
BK0121200US.book 33 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Using the LATCH system NOTE N00419100115 1. Open the gap a little between the seat cushion (A) and the seatback (B) with your hand to locate the lower anchors (C). ● In order to secure a child restraint systems compatible with the LATCH system, use the lower anchor points in the outboard positions of the rear seat. It is not necessary to use the vehicle’s seat belt.
BK0121200US.book 34 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems 3. Open the cover for the tether anchor by pulling it back with your hand as illustrated below (3). 4. Latch the tether strap hook (D) of the child restraint system to the anchor (E) as illustrated below (4) and tighten the top tether strap so it is securely fastened.
BK0121200US.book 35 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Installation: 1. Place the child restraint system in the rear seating position. 2. Route the seat belt through the child restraint system according to the instructions provided by the child restraint manufacturer. Then insert the seat belt latch plate into the buckle. Make sure you hear a “click” when you insert the latch plate into the buckle. 3.
BK0121200US.book 36 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems 5. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt allowing the slack to feed into the retractor. Remember, if the lap belt portion is not tight, the child restraint system will not be secure.
BK0121200US.book 37 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems 9. To remove a child restraint system from the vehicle and deactivate the ALR mode, remove the child from the restraint. Unlatch the buckle. Then remove the belt from the restraint and let the belt fully retract. ! WARNING ● Never allow children to play in the trunk of your vehicle.
BK0121200US.book 38 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Maintenance and inspection of seat belts N00407000221 The seat belt webbing may be cleaned with mild soap or detergent solution. Do not use an organic solvent. Allow the belts to dry in the shade. Do not allow them to retract until completely dry. Do not attempt to bleach or re-dye the belts. The color may rub off and the webbing strength may be affected.
BK0121200US.book 39 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● IT IS VERY IMPORTANT TO ALWAYS WEAR YOUR SEAT BELT PROPERLY EVEN WITH AN AIR BAG. • Seat belts help keep the driver and passengers properly positioned. This reduces the risk of injury in all collisions, and reduces the risk of serious injuries or death when the air bags inflate.
BK0121200US.book 40 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● Air bags inflate very quickly and with great force. Do not sit on the edge of the seat or lean your head or chest close to the steering wheel or the instrument panel. ● Do not put your feet or legs on or against the instrument panel. 2 2-40 ! WARNING ● Infants and small children should never ride unrestrained, or lean against the instrument panel. They should never ride held in your arms or on your lap.
BK0121200US.book 41 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● NEVER put REAR-FACING CHILD RESTRAINTS or INFANT RESTRAINTS seat in the front passenger seat. This places the infant too close to the passenger air bag. During deployment of that air bag, the infant can be seriously injured or killed. Rear-facing child restraints or infant restraints must only be used in the rear seat. ! WARNING ● FRONT-FACING CHILD RESTRAINTS should be used in the rear seat whenever possible.
BK0121200US.
BK0121200US.book 43 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems When the impact sensors detect a sufficient front or side impact to deploy the air bag(s), the appropriate air bag(s) will be deployed. When air bags deploy, some smoke is released accompanied by a loud noise. The smoke is not harmful, but do not intentionally inhale the smoke as it may cause temporary irritation to people with respiratory problems.
BK0121200US.book 44 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Driver’s seat position sensor 2 Passenger’s seat weight sensors N00417900092 N00418000087 The driver’s seat position sensor is attached to the seat rail and provides the air bag control unit with information on the seat’s fore-aft position. The air bag control unit controls deployment of the driver’s front air bag in accordance with the information it receives from this sensor.
BK0121200US.book 45 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● To ensure that the passenger’s seat weight sensors can correctly sense the weight being applied to the seat, observe the following instructions. Failure to follow these instructions can adversely affect the performance of the passenger’s air bag system. • Adjust the seat to the correct position, and sit well back against the seatback. Refer to “Front seat” on page 2-4.
BK0121200US.book 46 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Passenger’s air bag off indicator N00418100088 The passenger’s air bag off indicator is located above the central vents in the instrument panel. 2 The indicator normally comes on when the ignition switch is turned to the “ON” position and goes out a few seconds later. In the following situations, the indicator will stay on to show that the passenger’s front air bag is not operational.
BK0121200US.book 47 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems SRS warning light N00408300104 There is a Supplemental Restraint System (SRS) warning light on the instrument panel. The system checks itself each time the ignition is turned on. When the ignition key is in the “ON” or “START” position, the SRS warning light should come on for several seconds and then go out. This means the system is working properly.
BK0121200US.book 48 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Driver’s and passenger’s front air bag system N00407900204 2 The driver’s air bag is located under the padded cover in the middle of the steering wheel. The front passenger’s air bag is contained in the instrument panel above the glove compartment. The driver’s air bag and the front passenger’s air bag are designed to deploy at the same time.
BK0121200US.book 49 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Deployment of front air bags N00408000143 The front air bags ARE DESIGNED TO DEPLOY when … Head-on collision with a solid wall at speeds of approx. 15 mph (25 km/h) or higher Moderate to severe frontal impact within the shaded area between the arrows 2 The front air bags are designed to deploy when the vehicle suffers a moderate to severe frontal impact. A typical condition is shown in the illustration to the left.
BK0121200US.book 50 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems The front air bags MAY NOT DEPLOY when … In certain types of frontal collisions, the front air bags may not deploy, even if the deformation of the body seems to be large, because the vehicle’s body structure is designed to absorb the impact and deform in order to help protect the occupants. Some typical situations where the front air bags may not deploy are shown in the illustrations.
BK0121200US.book 51 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems The front air bags ARE NOT DESIGNED TO DEPLOY when … Rear end collision to your vehicle The front air bags are not designed to deploy in situations where they cannot provide protection to the occupants. Some typical situations are shown in the illustrations. Because the front air bags do not protect the occupants in all types of collisions, be sure to always wear your seat belts properly.
BK0121200US.book 52 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems The front air bags MAY DEPLOY when … The front air bags may deploy if the underside of the vehicle suffers a moderate to severe impact (undercarriage impact). Some typical these situations are shown in the illustrations.
BK0121200US.book 53 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● Do not attach anything to the steering wheel’s padded cover, such as trim material, badges, etc. These could strike and injure an occupant if the air bag inflates. ● Do not set anything on, or attach anything to, the instrument panel above the glove compartment. Such items could strike and injure an occupant if the air bag inflates. ! WARNING ● Do not attach accessories to, or put them in front of, the windshield.
BK0121200US.book 54 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Side air bag system N00408100388 The side air bags (A) are contained in the driver and front passenger seatbacks. The side air bag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat. 2 2-54 A label is attached to the seatbacks in vehicles with side air bags.
BK0121200US.book 55 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Curtain air bag system N00419200158 The curtain air bags are contained in the front and rear pillars and roof side rail. The curtain air bag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat. ! WARNING ● The side air bags and curtain air bags can cause serious injury or death to anyone too close to the air bag when it deploys.
BK0121200US.book 56 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! 2 WARNING ● In order to reduce the risk of injury from a deploying side air bag, do not allow any rear seat passengers to hold onto the back of either front seat. Special care should be taken with children. ● Do not place any objects near or around the front of either front seatback. Such objects can interfere with proper side air bag deployment and cause injury during deployment of the side air bag.
BK0121200US.book 57 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● Do not put a hanger or any heavy or pointed object on the coat hook. If the curtain air bag was activated, any such item could be propelled away with great force and could prevent the curtain air bag from inflating correctly. Hang clothes directly on the coat hook (without using a hanger). Make sure there are no heavy or sharp objects in the pockets of clothes that you hang on the coat hook.
BK0121200US.book 58 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Deployment of side air bag and curtain air bag N00408200031 The side air bag and curtain air bag ARE DESIGNED TO DEPLOY when … A side air bag and curtain air bag are designed to deploy when the vehicle suffers a moderate to severe side impact to the middle of the passenger compartment. The typical situation is shown in the illustration.
BK0121200US.
BK0121200US.book 60 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems The side air bag and curtain air bag ARE NOT DESIGNED TO DEPLOY when … The side air bag and curtain air bag are not designed to deploy in situations where they cannot provide protection to the occupants. Some typical situations are shown in the illustrations. Because the side air bags and curtain air bags do not protect the occupants in all types of collisions, be sure to always wear your seat belts properly.
BK0121200US.book 61 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems ! WARNING ● If you find a crack in or damage to the front pillar, rear pillar, or roof side rail where the curtain air bag is located, have the SRS inspected by an authorized Mitsubishi Motors dealer. NOTE ● When you transfer ownership of the vehicle to another person, we urge you to alert the new owner that it is equipped with the SRS and refer that owner to the applicable sections in this owner’s manual.
BK0121200US.book 62 ページ 2010年4月14日 水曜日 午前11時24分 Seat and restraint systems Warning labels N00408600224 Occupant restraint warning labels for the SRS are located in the vehicle as shown in the illustration. 2 *: Located in the passenger’s side as well.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Break-in recommendations . . . . . . . . . . . . . . . . . .3Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Electronic immobilizer (Anti-theft starting system). . . . . . . . . . . . . . . . .3Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .3Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Keys Break-in recommendations N00508700226 3 Advanced automobile manufacturing techniques permit you to operate your new vehicle without requiring a long break-in period of low-speed driving. However, you can add to the future performance and economy of your vehicle by observing the following precautions during the first 300 miles (500 km). Drive your vehicle at moderate speeds during the break-in period. ● Avoid revving the engine.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● The key number (A) is stamped on the key number plate as shown in the illustration. Make a record of the key number and store the key and key number plate in separate places, so that you can order a key from your authorized Mitsubishi Motors dealer if the original keys are lost. ● The key is a precision electronic device with a built-in signal transmitter. Please observe the following in order to prevent a malfunction.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE 3 ● In the following cases, the vehicle may not be able to recognize the registered ID code from the key. This means the engine will not start even when the key is turned to the “START” position.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● Electronic immobilizer is not compatible with commercially available remote starting systems. Use of commercially available remote starting systems may result in vehicle starting problems and a loss of security protection. Use only Mitsubishi Motors authorized accessories. ● A system failure is suspected when the ignition key is turned to the “START” position, and the engine does not start.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 4. When the immobilizer indicator starts blinking, turn the second valid key to the “LOCK” position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition and turn it to the “ON” position. Perform this operation no more than 30 seconds after the immobilizer indicator starts blinking. When registration of the ID code is complete, the immobilizer indicator will come on for 3 seconds then go off.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Keyless entry system General information Your electronic immobilizer operates on a radio frequency subject to Federal Communications Commission (FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada). This device complies with Part 15 of the FCC Rules and RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions. ● This device may not cause harmful interference.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To lock Press the LOCK button (1) to lock all the doors. If they are locked while the dome light is not illuminated, the dome light will blink once. The turn signal lights will also blink once. ● The answerback function will not operate when the key is in the ignition switch. Horn deactivation/reactivation NOTE The answerback function can be set in the following three ways.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Turn signal light deactivation/reactivation The answerback function from the turn signal lights indicating when the doors are locked or unlocked can be turned on or off separately. A tone will sound once when the function has been turned on, and twice if it has been turned off. To deactivate/reactivate the answerback function for locking of the doors, take the following steps: 1.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ● If you lose your remote control transmitter, please contact an authorized Mitsubishi Motors dealer for a replacement. ● If you wish to obtain an additional remote control transmitter, please contact an authorized Mitsubishi Motors dealer. A maximum of 4 remote control transmitters can be programmed for your vehicle. Procedure for replacing the remote control transmitter battery 1.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 2. Remove the remote control transmitter from the remote control transmitter case. Then, open the remote control transmitter using the method described in step 1. 4. Install a new battery with the + side (A) down. + side - side Coin type battery CR1620 3. Remove the old battery. 5. Close the remote control transmitter firmly. 6.
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! ● When the remote control transmitter case is opened, be careful to keep water, dust, etc. out. Also, do not touch the internal components. 3 3-12 Door locks CAUTION N00509200390 ! WARNING ● Make sure all doors are tightly closed and locked while driving. • Locked doors, in combination with the use of seat belts, can help reduce the risk of ejection in an accident.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To lock or unlock the door with the key (driver’s door only) Turn the key toward the front of the vehicle to lock the door. After checking that the door is locked, turn the key back to the center and remove it. To lock or unlock the door from the inside Move the lock knob to the lock position to lock the door. All doors should be kept locked while driving.
BK0121200US.book 14 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Power door locks To lock the door without using the key 1. Move the inside lock knob to the locked position. 2. Be sure the keys are not inside the vehicle. Close the door. N00509300447 NOTE ● Repeated continuous operation between lock and unlock could activate the power door locking system’s built-in protection circuit and prevent the system from operating.
BK0121200US.book 15 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls “Child safety locks” for rear door For vehicles sold in Canada N00509400275 Except for vehicles sold in Canada 3 1- To lock 2- To release Child safety locks help prevent rear passengers, especially children, from opening the rear door using the inside door handle. A lock lever for the child safety lock is provided on each rear door.
BK0121200US.book 16 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! ● Always keep the doors tightly closed and locked when driving. An unlocked door may be accidentally opened by a passenger, especially by a child who could fall out. Also, if the doors are not locked, there is a greater risk of someone being thrown from the vehicle in an accident. 3 Trunk lid WARNING N00509500120 ! WARNING ● It is dangerous to drive with the trunk lid open since carbon monoxide (CO) gas can enter the cabin.
BK0121200US.book 17 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To open NOTE N00545200020 Operation from outside the vehicle Use the remote control transmitter to open. Press the trunk button. (See “Keyless entry system” on page 3-7.) The trunk lid will pop up slightly. Lift it to open the trunk. Operation from inside the vehicle ● The trunk light comes on when the trunk lid is opened, and goes out when it is closed.
BK0121200US.book 18 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● Before starting the vehicle, be sure to confirm that the trunk lid is closed. If the trunk lid opens while driving the vehicle, objects stored in the trunk could fall out onto the road. Inside emergency trunk lid release N00509800123 The emergency trunk lid release is designed to provide a way to open the trunk lid from inside the trunk.
BK0121200US.book 19 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls You and your family should familiarize yourselves with the location and operation of the emergency trunk lid release handle. Children should be taught not to play in or around vehicles. ! To open the trunk from the inside, pull the handle in the direction of the arrow on the handle. Push up on the trunk lid to open the trunk and climb out. WARNING Handle ● Children should never be left unsupervised in or around vehicles.
BK0121200US.book 20 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Theft-alarm system (if so equipped) NOTE N00510200042 The theft-alarm system is designed to provide protection from unauthorized entry into the vehicle. This system is operated in three stages: the first is the “armed” stage, the second is the “alarm” stage, and third is the “disarmed” stage. If triggered, the system provides both audible and visual alarm signals. Armed stage N00510300072 3 Park the vehicle and stop the engine.
BK0121200US.book 21 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● The system will be armed even if the engine hood is open, but when the system is set, be sure that the engine hood is locked. ● The system will be disarmed if, while the theft-alarm indicator (located in the front center of the dashboard) is illuminated, all doors are unlocked by remote control transmitter.
BK0121200US.book 22 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Disarmed stage Testing the theft-alarm system N00510500074 N00510600046 The system will be disarmed when either of the following steps are taken: 1. All doors are unlocked by the remote control transmitter. 2. The ignition key is turned to the “ACC” or “ON” position. 3. If the UNLOCK button is pressed when all doors are closed and no door is opened within approximately 30 seconds, re-arming will automatically occur.
BK0121200US.book 23 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Power windows N00510800312 ! WARNING ● Before operating the power windows, make sure that nothing can be trapped (head, hands, fingers, etc.) in the window. ● Never leave the vehicle without removing the key. ● Never leave a child alone in the vehicle. 3 1- Open (down) 2- Close (up) NOTE ● Never try to operate the main switch and sub switch in different directions at the same time. This will freeze the window in position.
BK0121200US.book 24 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Main switch Sub switch The main switch located on the driver’s door can be used to operate all the door windows. The windows will move while the switch is pressed and stop when the switch is released. 3 1- Close 2- Open A sub switch can be used for its own passenger door window, unless the driver’s window lock switch is activated.
BK0121200US.book 25 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Lock switch N00549000039 When this switch is in the lock mode, the passenger door switches cannot be used to open or close the door windows, and the main switch will open or close only the driver’s door window. To unlock the switch, press it again. What to do if you hear wind buffeting when driving N00551400014 Wind buffeting can be described as the perception of pressure on the ears or a booming or rumbling sound.
BK0121200US.book 26 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Sunroof (if so equipped) To close N00511000597 The sunroof can be opened and closed with the ignition key in the “ON” position. The sunroof closes while the switch (3) is pressed. To tilt up When the switch (2) is pressed, the rear edge of sunroof raises for ventilation. To tilt down The sunroof tilt down while the switch (3) is pressed. Timer function The sunroof can be operated when the ignition key is in the “ON” position.
BK0121200US.book 27 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Sunshade The sunshade can be opened or closed manually while the sunroof is closed. When the sunroof is opened, the sunshade will also open automatically. ! WARNING ● Do not stick your head, hands or anything else in the sunroof opening. ● Before operating the sunroof, make sure that nothing can be trapped (head, hands, fingers, etc.).
BK0121200US.book 28 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ● Do not put any wax on the weatherstrip (black rubber) around the sunroof opening. If it is waxed, the weatherstrip cannot maintain a weatherproof seal with the sunroof. ● After washing the vehicle or after rain be sure to wipe off any water that is on the sunroof before operating it. ● Operating the sunroof repeatedly with the engine turned off will run down the battery. Operate the sunroof only while the engine is running.
BK0121200US.book 29 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To release Steering wheel tilt lock lever N00511500156 To adjust the steering wheel height, release the tilt lock lever while holding the steering wheel by hand, and raise or lower the steering wheel to the desired height. After adjustment, securely lock the lever by pulling it upward. 3 1- Pull the lever up slightly. 2- Press and hold the button at the end of the hand grip. 3- Push the lever downward.
BK0121200US.book 30 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! Inside rearview mirror WARNING ● After adjusting, make sure the lock lever is secured in the locked (1) position. ● Do not attempt to adjust the steering wheel while driving. This can be dangerous. ● When releasing the tilt lock lever {moving it to the position (2)}, be sure to hold the steering wheel firmly. Otherwise, the steering wheel may slip down too suddenly.
BK0121200US.book 31 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Adjust the inside mirror to maximize the view through the rear window. To reduce the glare To adjust the vertical mirror position The day/night knob (A) at the bottom of the mirror can be used to adjust the mirror to reduce the glare from the headlights of vehicles behind you during night driving. It is possible to move the mirror up and down to adjust its position.
BK0121200US.book 32 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Outside rearview mirrors Type 2 When the headlights of the vehicles behind you are very bright, the reflection factor of the rearview mirror is automatically changed to reduce the glare. N00512200189 Adjust the outside rearview mirrors only after making any seat adjustments so you have a clear view to the rear of the vehicle. ! WARNING ● Do not attempt to adjust the outside rearview mirrors while driving. This can be dangerous.
BK0121200US.book 33 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To adjust the mirror position The outside rearview mirrors can be adjusted when the ignition key is in the “ON” or “ACC” position. Move the lever (A) to the same side as the mirror you wish to adjust. Heated mirror (if so equipped) N00549300133 When the rear window defogger switch is pressed, the outside rearview mirrors are defogged or defrosted.
BK0121200US.book 34 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Ignition switch START N00512400657 Engages the starter. After the engine starts, release the key and it will return automatically to the “ON” position. NOTE ● If your vehicle is equipped with ignition switch illumination, the ignition switch will be illuminated: • The ignition switch illumination comes on while the driver’s door is opened and remains on for about 30 seconds after the driver’s door is closed.
BK0121200US.book 35 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To remove the key ! CAUTION ● Do not turn the key to the “START” position when the engine is running. It will damage the starter motor. Key reminder buzzer N00551000078 If you open the driver’s door while the ignition key is in the “LOCK” or “ACC” position, a tone will sound, reminding you to remove the key. 3 First set the selector lever to the “P” (PARK) position, and then turn the key to the “LOCK” position and remove it.
BK0121200US.book 36 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Steering wheel lock NOTE N00512500137 3 To lock Remove the key at the “LOCK” position. Turn the steering wheel until it is locked. To unlock Turn the key to the “ACC” position while moving the steering wheel slightly. ! CAUTION ● Remove the key when leaving the vehicle. ● If your vehicle needs to be towed, turn the key to the “ACC” position to unlock the steering wheel.
BK0121200US.book 37 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Starting N00512600691 Tips for starting ● Do not operate the starter motor continuously for longer than 15 seconds as this could run the battery down or damage the starter motor. If the engine does not start, turn the ignition switch back to the “LOCK” position, wait a few seconds, and then try again. Trying repeatedly with the engine or starter motor still turning will damage the starter mechanism.
BK0121200US.book 38 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Startability of automatic transaxle vehicle with ambient temperature of -31 °F (-35 °C) or lower When the ambient temperature is -31 °F (-35 °C) or lower, it may not be possible to start from a standstill even with the selector lever in the “D” (DRIVE) position. This phenomenon occurs because the transaxle has not warmed up sufficiently; it does not indicate a problem.
BK0121200US.book 39 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Automatic transaxle NOTE N00513200098 Designed for the most efficient control and equipped with selfadapting capabilities, the electronically controlled transaxle used in your vehicle selects the most favorable gear for each type of driving and road condition. DRIVING UPHILL The transaxle may not shift to a higher gear if the computer determines your current speed would be affected.
BK0121200US.book 40 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls The transaxle has 4 forward gears and 1 reverse gear. The individual gears are selected automatically, depending on the position of the gear selector lever, the speed of the vehicle and the position of the accelerator pedal. The selector lever has 2 “gates”: the main gate (A) and the manual gate (B). 3 NOTE ● For information on manual gate operation, refer to “Sports mode” on page 3-44.
BK0121200US.book 41 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! WARNING ● Always depress the brake pedal when shifting the selector lever into a gear from the “N” (NEUTRAL) position. When beginning to drive, do not shift the selector lever from the “N” (NEUTRAL) position while depressing the accelerator pedal. This will cause the vehicle to “jump” forward or backward.
BK0121200US.book 42 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Selector lever position indicator/ “N” indicator N00513900314 3 A- Selector lever position indicator When the ignition key is turned to the “ON” position, the indicator in the instrument cluster comes on to show the position of the selector lever (i.e. “PARK”, “DRIVE”, “REVERSE”, etc.). B- “N” indicator When the “N” indicator blinks while you are driving, there could be a malfunction in the automatic transaxle.
BK0121200US.book 43 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Selector lever positions “N” NEUTRAL N00514200268 “P” PARK This position locks the transaxle to prevent the vehicle from moving. The engine can be started from the “PARK” position. “R” REVERSE Move the lever to this position only after the vehicle has come to a complete stop. ! CAUTION ● Never shift into the “P” (PARK) or “R” (REVERSE) position while the vehicle is in motion.
BK0121200US.book 44 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Sports mode N00514400387 Whether the vehicle is stationary or in motion, sports mode is selected by pushing the selector lever from the “D” position into the manual gate. To return to “D” range operation, push the selector lever back into the main gate. In sports mode, gear shifts can be made rapidly simply by moving the selector lever backward and forward. Sports mode allows gear shifts with the accelerator pedal depressed.
BK0121200US.book 45 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ● Move the selector lever gently between the manual and main gates and between positions in the manual gate. Excessive force could damage the selector lever. ● When sports mode is selected, the “D” indicator goes out. Sports mode indicator In sports mode, the currently selected gear is indicated by the indicator shown on the instrument cluster.
BK0121200US.book 46 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● Use the selector lever in the correct shift position in accordance with driving conditions. Never coast downhill backward in the driving shift position {“D” (DRIVE) or sports mode} or coast forward in the “R” (REVERSE) position. Engine stopping and Increased brake pedal and steering effort could lead to an accident.
BK0121200US.book 47 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Service brake Parking N00515100017 To park the vehicle, first bring it to a complete stop, fully engage the parking brake, and then move the selector lever to the “P” (PARK) position.
BK0121200US.book 48 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Power brakes Brake pad wear alarm N00517600319 3 Your vehicle is equipped with power brakes for more braking force with minimal brake pedal effort. Your brakes are designed to operate at full capacity, even if the power assist is lost. If the power assist is lost, the effort needed to press the brake pedal is greater. If you should loose the power assist for some reason, the brakes will still work.
BK0121200US.book 49 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Anti-lock braking system N00517900253 The anti-lock braking system helps prevent the wheels from locking up when braking. This helps you keep control of your vehicle and its direction. Driving hints ● When using the anti-lock brakes (sudden braking), steering is slightly different from normal driving conditions. Use the steering wheel carefully. ● Always keep a safe distance from the vehicle in front of you.
BK0121200US.book 50 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Anti-lock braking system warning light If the warning light illuminates while driving N00531600427 N00531700369 This light comes on in the event of a malfunction in the antilock braking system. It will also come on as a self-check for a few seconds when the ignition key is turned to the “ON” position. Always make sure that the light goes out before beginning to drive.
BK0121200US.book 51 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Active stability control (ASC) Front N00559100088 The active stability control (ASC) takes overall control of the anti-lock braking system, traction control function and skid control function to help maintain the vehicle’s control and traction. Also refer to the following pages on the anti-lock braking system, traction control function and skid control function. Anti-lock braking system (ABS) → P.3-49 Traction control function → P.
BK0121200US.book 52 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE 3 ● A whining sound may be heard from the engine compartment in the following situations. The sound is associated with the ASC self-check operations. It does not indicate a malfunction. • When the ignition key is set to the “ON” position. • When the vehicle is driven for a while after the engine is turned on.
BK0121200US.book 53 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Skid control function ASC OFF switch N00546800036 N00559400094 The skid control function is designed to help the driver maintain control of the vehicle on slippery roads or during rapid steering maneuvers. It works by controlling the engine output and the brake on each wheel. The ASC is automatically activated when the ignition key is turned to the “ON” position.
BK0121200US.book 54 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE 3 ● Using the ASC OFF switch turns off both the skid control function and the traction control function. ● When moving out of mud, sand or fresh snow, pressing the accelerator pedal may not allow the engine speed to increase. In such situations, temporarily deactivate the ASC, using the ASC OFF switch.
BK0121200US.book 55 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● When indicator blinks, the ASC is operating, which means that the road is slippery or that your vehicle’s wheels are beginning to slip. If this happens, drive slower. NOTE ● When a spare tire has been put on your vehicle, the gripping ability of the tire will be lower, making it more likely that the indicator will blink.
BK0121200US.book 56 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! Power steering system CAUTION ● If the vehicle is towed with the ignition key in the “ON” position and only the front wheels or only the rear wheels raised off the ground, the ASC may operate, resulting in an accident. When towing the vehicle with the front wheels raised, keep the ignition key in the “LOCK” or “ACC” position. When towing the vehicle with the rear wheels raised, keep the ignition key in the “ACC” position.
BK0121200US.book 57 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Cruise control N00518300469 Cruise control is an automatic speed control system. It lets you keep the same driving speed. Cruise control can be used at speeds of about 25 mph (40 km/h) or more. It is especially useful for freeway driving. Cruise control does not work at speeds below about 25 mph (40 km/h).
BK0121200US.book 58 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Cruise control indicator To activate N00550100173 N00518400196 This indicator will come on when the cruise control main switch is “ON”. 1. Momentarily push in the main switch (A) at the end of the cruise control lever.
BK0121200US.book 59 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 2. Pull the lever (B) down while driving at the desired speed. To increase the set speed N00518500243 There are 2 ways to increase the set speed. Cruise control lever Pull the cruise control lever up and hold it while driving at the set speed, and your speed will then gradually increase. When you reach your desired speed, release the switch. Your cruising speed is now set.
BK0121200US.book 60 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Accelerator pedal Press the accelerator pedal to reach your desired speed. Pull the cruise control lever down for a moment, then release it. To decrease the set speed N00518600114 There are 2 ways to reduce the set speed. Cruise control lever Pull the cruise control lever down and hold it while driving at the set speed, and you will slow down (coast) gradually. When your desired low speed is reached, release the lever.
BK0121200US.book 61 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Brake pedal Press the brake pedal (which disengages the cruise control), then pull the cruise control lever down momentarily to set a new desired cruise speed. To accelerate for passing N00518700098 Press the accelerator pedal as you would normally. When you release the pedal, the cruise control will return to your set speed.
BK0121200US.book 62 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls To deactivate N00518800523 The cruise control can be turned off as follows: ● Push the main switch (A) at the end of the lever. (Main switch OFF) ● Pull the cruise control lever (B) toward you. ● Depress the brake pedal. 3 The cruise control can be turned off automatically in any of the following ways: ● When your speed slows to about 10 mph (15 km/h) or more below the set speed because of a hill, etc.
BK0121200US.book 63 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Tire pressure monitoring system To resume the set speed N00518900120 If the speed memory has not been erased, resume the previously set speed by pulling the cruise control lever up while driving at a speed of 25 mph (40 km/h) or higher. N00530200341 The tire pressure monitoring system uses tire inflation pressure sensors (A) on the wheels to monitor the tire inflation pressures.
BK0121200US.book 64 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! WARNING ● The compact spare wheel does not have a tire inflation pressure sensor. When the spare tire is used, the tire pressure monitoring system will not work properly. See an authorized Mitsubishi Motors dealer as soon as possible to replace or repair the original tire. NOTE 3 ● The tire pressure monitoring system is not a substitute for regularly checking tire inflation pressures.
BK0121200US.book 65 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Tire pressure monitoring system warning light N00554800080 When the ignition key is turned to the “ON” position, this light normally illuminates and goes off a few seconds later. If one or more of the vehicle tires (except for the spare tire) is significantly under-inflated, however, this light will remain illuminated while the key is in the “ON” position.
BK0121200US.book 66 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
BK0121200US.book 67 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls If the warning light illuminates while driving N00532800370 1. Avoiding hard braking, sharp steering maneuvers and high speeds. You should stop and adjust the tires to the proper inflation pressure as soon as possible. Adjust the spare tire at the same time. Refer to “Tires” on page 7-19. NOTE ● When inspecting or adjusting the tire pressure, do not apply excessive force to the valve stem to avoid breakage.
BK0121200US.book 68 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 3 The tire pressure monitoring system may not work normally in the following circumstances: ● A wireless facility or device using the same frequency is near the vehicle. ● Snow or ice is stuck inside the fenders and/or on the wheels. ● The tire inflation pressure sensors’ battery is exhausted. ● Wheels other than Mitsubishi Motors genuine wheels are being used.
BK0121200US.book 69 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Rear-view camera (if so equipped) General information N00533000148 Your tire pressure monitoring system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada). This device complies with Part 15 of the FCC Rules and RSS- 210 of the Industry Canada Rules. Operation is subject to the following two conditions.
BK0121200US.book 70 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Location of rear-view camera Screen image The rear-view camera (A) is in the trunk lid. Reference guide marks, upper surface of the rear bumper (A) and a part of the trunk lid (C) are displayed on the screen. ● Five guide marks in red (B) indicates approximately 20 inches (50 cm) behind the rear bumper. ● Each row of green guide marks (1 to 4) indicates approximately 8 inches (20 cm) outside of the vehicle body.
BK0121200US.book 71 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● The rear-view camera uses a wide-angle lens. As a result, images and distances shown on the screen are not exact. ● Actual distance may be different from distance indicated by the guide marks on the screen, depending on the loading condition of the vehicle and road surface condition. NOTE ● Mirror image is displayed on the screen. ● It is possible to set the display language of the screen to English, Spanish or French.
BK0121200US.
BK0121200US.book 73 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Speedometer Odometer/Trip odometer N00519100015 The speedometer shows your vehicle’s speed. N00519500338 When the ignition switch is in the “ON” position, an “ODO” or “TRIP” indicator is displayed. Tachometer N00519200032 The tachometer shows engine revolutions per minute. This allows the driver to determine the most efficient gear range and engine speed combinations. This gauge also assists in evaluating engine performance.
BK0121200US.book 74 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Every time the reset button (3) is pressed lightly (less than one second), the indicators are changed. To reset the trip meter To zero the counter, press and hold the reset button for more than one second. Only the currently displayed value will be reset. If TRIP is displayed, for example, only TRIP will be reset. NOTE 3 ODO-Odometer The odometer shows the total distance the vehicle has traveled.
BK0121200US.book 75 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Fuel gauge Fuel tank filler door mark N00519600052 This gauge shows the amount of fuel in the fuel tank when the ignition key is turned to the “ON” position. The arrow (A) indicates that the fuel tank filler door is located on the left side of the vehicle (Refer to “Filling the fuel tank” on page 1-4).
BK0121200US.book 76 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Engine coolant temperature gauge N00519700037 This gauge shows the engine coolant temperature. If the temperature is low when the ignition key is turned to the “ON” position, the indicator will remain at the “C” (cold) position until the engine begins to warm up. The indicator will normally stay near the center while driving, but may rise slightly in stop-and-go traffic or when the engine is under a heavy load.
BK0121200US.book 77 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Indicator and warning light package N00519800780 3 1- Engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) → P.3-79 2- Cruise control indicator → P.3-58 3- High beam indicator → P.3-78 4- Turn signal indicators/Hazard warning lights → P.3-78 5- Front fog light indicator (if so equipped) → P.3-78 6- Automatic transaxle position indicator → P.3-42 7- Active stability control (ASC) indicator → P.
BK0121200US.book 78 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Warning lights Indicator N00519900042 Turn signal indicators/Hazard warning lights Brake warning light N00520000157 N00520400252 The arrows will flash in time with the corresponding exterior turn signals when the turn signal lever is used. This light comes on when the ignition key is turned to the “ON” position (engine off). When the engine is started, the light should go off.
BK0121200US.book 79 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● The vehicle should be brought to a stop in the following manner when brake performance has deteriorated while driving. • Press the brake pedal harder than usual. • Should the brakes fail, shift down to a lower gear to reduce your speed and slowly pull the parking brake lever to park your vehicle. Press the brake pedal to operate your rear brake lights to alert vehicles behind you.
BK0121200US.book 80 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Charging system warning light N00520900299 This light comes on in the event of a malfunction in the charging system or when the ignition key is turned to the “ON” position (engine off). When the engine is started, the light should go out. Check to make sure that the light has gone out before driving. This light comes on when any door is open or not completely closed.
BK0121200US.book 81 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Combination headlights and dimmer switch N00522500622 Headlights Rotate the switch to operate the lights. [When the engine is started and the parking brake is released] The daytime running lights come on.
BK0121200US.book 82 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ● When it rains, or when the vehicle has been washed, the inside of the lens sometimes becomes foggy. This is the same as when window glass mists up on a humid day, and does not indicate a problem. When the light is switched on, the heat will dry out the fog. However, if water collects inside the light, have it checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 83 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 3. The light will automatically turn off after 3 minutes. Dimmer (high/low beam change) N00549900126 NOTE ● When the driver’s door is opened, a continuous highpitched tone will sound if the key has been removed; a continuous low-pitched tone will sound if the key is in the ignition switch. The tone stops sounding when the driver’s door is closed.
BK0121200US.book 84 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Turn signal lever Headlight flasher N00550000169 You can flash the high beams by pulling the lever gently toward you (2). The lights will go back to normal when you let go. While the high beam is on, you will see a blue light on the instrument panel. NOTE 3 ● You can flash the high beams by pulling the lever toward you, even if the light switch is off.
BK0121200US.book 85 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Hazard warning flasher switch NOTE ● A light in the instrument panel flashes to show when the front and rear turn signal lights are working properly. If this light flashes faster than usual, check for a burned out lamp bulb or malfunctioning connection. If the panel light does not come on when the lever is moved, check for a blown fuse or a burned out bulb in the panel.
BK0121200US.book 86 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Fog light switch (if so equipped) N00522800364 The fog lights illuminate only when the headlights are on low beam. Press the switch to illuminate. Press the switch again to turn the lights off. The indicator in the instrument cluster will illuminate while the fog lights are on.
BK0121200US.book 87 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Instrument panel light dimmer control Wiper and washer switch N00522900176 The brightness of the instrument panel lights can be adjusted by turning this control while the light switch is in the “ ” or “ ” position. N00523000549 Windshield wipers The windshield wipers wipe when the wiper lever is moved as shown in the illustration and the ignition key is in the “ON” or “ACC” position.
BK0121200US.book 88 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● For vehicles equipped with the Mitsubishi Multi-Communication System, Mitsubishi Multi-Communication System can be used to enable and disable speed-sensitive operation of the wipers. For details, refer to the separate owner’s manual. To adjust intermittent intervals With the lever in the “INT” (speed-sensitive) position, the intermittent intervals can be adjusted by turning the knob (A).
BK0121200US.book 89 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Windshield washer N00504600025 To turn on the windshield washer, pull the lever toward you with the ignition key in either the “ON” or “ACC” position. The wipers will wipe automatically several times when the washer fluid is sprayed. To turn off the spray, release the lever.
BK0121200US.book 90 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ● Replace the wiper blades when they are worn. Use the proper size replacement blades. If you have questions, ask your authorized Mitsubishi Motors dealer. Electric rear window defogger switch N00523700357 The electric rear window defogger can be used with the ignition key in the “ON” position. The indicator light (A) will come on when you press the electric rear window defogger switch.
BK0121200US.book 91 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls ! CAUTION ● The rear window defogger is not designed to melt snow. Remove any snow manually before using the rear window defogger. ● Use the rear window defogger only after the engine has started and is running. Be sure to turn the defogger switch off immediately after the window is clear to save on battery power. ● Do not place stickers, tape, or other items that are attached with adhesive over the grid wires on the rear window.
BK0121200US.book 92 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Hands-free Bluetooth® cellular phone interface system with voice recognition (if so equipped) N00506400102 3 The Hands-free Bluetooth® cellular phone interface system with voice recognition (Bluetooth® HFP) uses a wireless communication technology known as Bluetooth® to allow you to make hands-free calls in your vehicle using your Bluetooth® compatible cellular phone with Hands-free profile.
BK0121200US.book 93 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Overhead console control switch PHONE button N00546700048 1- PHONE button 2- SPEECH button 3- microphone ● Press this button when an incoming call is received to answer the telephone. ● When another call is received during a call, press this button to put the first caller on hold and talk to the new caller. • In such circumstances, you can press the button briefly to switch between callers.
BK0121200US.book 94 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE 3 ● When you press the SPEECH button to enter voice recognition mode with a cellular phone paired to the system, current information on the cellular phone, such as “remaining battery life,” “signal strength” or “roaming,” will be displayed on the audio display.* (Refer to “Pairing a cellular phone” on page 3-100.) *: Some cellular phones will not send this information to the Bluetooth® HFP.
BK0121200US.book 95 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Change the language using the “Language” command 1. Press the SPEECH button. 2. Say “Setup.” 3. Say “Language.” 4. The voice guide will say “Select a language: English, French or Spanish.” Say the desired language. (Example: Say “English.”) 5. The voice guide will say “English (Spanish or French) selected. Is this correct?” Say “Yes” to start the language change process. Say “No” to return to Step 4. 6.
BK0121200US.book 96 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Speaker enrollment NOTE N00529000020 It takes a few minutes to complete the speaker enrolment process. To ensure the best results, run through the process while in the driver’s seat, in an environment that is as quiet as possible (when there is no rain or strong winds and the vehicle windows are closed). Use the following procedure for speaker enrollment. 1.
BK0121200US.book 97 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 8. When all enrollment commands have been read out, the voice guide will say “Speaker Enrollment is complete.” The system will then end the speaker enrollment process and return to the main menu. NOTE ● Completing the speaker enrollment process will turn on the voice model automatically. ● The commands “Help” and “Cancel” will not work in this mode. Enabling and disabling the voice model and retraining N00529100050 4.
BK0121200US.book 98 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Help function N00506700033 The Bluetooth® HFP is equipped with a Help function. If you say “Help” when the system is waiting for a voice command input, the system will tell you a list of the commands that can be used under the circumstances. Canceling N00506800034 3 There are two cancel functions. If you are at the main menu, say “Cancel” to exit from the Bluetooth® HFP.
BK0121200US.book 99 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Setting the passcode N00539000010 Use the following procedure to turn on the security function by setting a passcode. 1. Press the SPEECH button. 2. Say “Setup.” 3. Say “Passcode.” 4. The voice guide will say “Passcode is disabled. Would you like to enable it?” Answer “Yes.” Answer “No” to cancel the setting of the passcode and return to the main menu. 5. The voice guide will say “Please say a 4-digit passcode. Remember this passcode.
BK0121200US.book 100 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Pairing a cellular phone N00507100164 To use the Bluetooth® HFP, you need to pair a Bluetooth® compatible cellular phone to the Bluetooth® HFP. The Bluetooth® HFP can register up to a maximum of 7 Bluetooth® compatible cellular phones. However, of the cellular phones registered, the cellular phone with the highest priority level will be automatically paired to the Bluetooth® HFP.
BK0121200US.book 101 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 7. After the voice guide says “Please say a 4-digit pairing code,” say a 4-digit code. The 4-digit code will be registered as a pairing code for the phone. When the confirmation function is on, the system will confirm whether the code said is acceptable. To continue with the code, answer “Yes.” Say “No” to return to pairing code selection. NOTE ● The pairing code entered here is only used for the Bluetooth® connection certification.
BK0121200US.book 102 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 11. After the voice guide says “ set to priority ,” the system will start the pairing process. Wait a moment for the pairing process to complete. When the confirmation function is on, the system will confirm the assigned phone name and priority again. Answer “Yes.” Answer “No” to return to the priority level selection in Step 10. 12.
BK0121200US.book 103 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Having the system tell you a list of the registered cellular phones N00507300052 You can use the following procedure to hear a list of the cellular phones that are currently registered. 1. Press the SPEECH button. 2. Say “Setup.” 3. Say “Pairing Options.” 4. The voice guide will say “Do you want to Pair a phone, delete a phone or list paired phones?” Say “list paired phones.” 5.
BK0121200US.book 104 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 7. When the phone deletion process is completed, the voice guide will say “Deleted.” The system will then beep and the voice recognition mode will be exited. If the phone deletion process fails for some reason, the voice guide will say “Delete failed.” The system will then beep and the voice recognition mode will be exited. Start over again from Step 1.
BK0121200US.book 105 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 5. After the voice guide says “Calling at ,” the Bluetooth® HFP will make the call. When the confirmation function is on, the system will confirm whether or not the name of the recipient of the call is correct. Answer “Yes” to use that name. If you want to change the name or location to call, answer “No.” The system will return to Step 3.
BK0121200US.book 106 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Switching between hands-free mode and private mode N00508100031 The Bluetooth® HFP can switch between Hands-free mode (Hands-free calls) and private mode (calls using cellular phone). If you press the SPEECH button and say “Transfer call” during a Hands-free call, you can stop the Hands-free mode and talk in private mode on your cellular phone. To return to Hands-free mode, press the SPEECH button again and say “Transfer call.
BK0121200US.book 107 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls New entry 3. Say the telephone number to register it. N00508400050 You can register a new entry in the phonebook by saying “New entry” on the phonebook main menu. You can register up to a maximum of 32 entries. Use the following procedure to register a new entry. 1. If you have not reached the limit yet, the voice guide will say “Name Please.” Say your preferred name to register it.
BK0121200US.book 108 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Edit N00508500035 You can edit information in the phonebook by saying “Edit” on the phonebook main menu. 1. The voice guide will say “Please say the name of the entry you would like to edit, or say “list names,” or say “cancel” to return to main menu.” Say the name of the entry that you want to edit.
BK0121200US.book 109 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Having the system tell you a list of the phonebook entries N00508600052 You can hear a list of the names registered in the phonebook by saying “List names” on the phonebook main menu. 1. The Bluetooth® HFP will read out the entries in the phonebook in order. 2.
BK0121200US.book 110 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 4. When the deletion of the telephone number is completed, the voice guide will say “ deleted” and then the system will return to the main menu. NOTE ● If you delete all telephone numbers registered for the 4 locations of an entry, the entry itself will be deleted from the phonebook.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.book 121 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Sun visors Slide plate N00524600063 Fold the sun visor downward (1) to reduce front glare while driving. To reduce side glare, turn the visor to the side (2). To block out additional side glare, swing the sun visor sideways and pull out the slide plate (A).
BK0121200US.book 122 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Power outlet Vanity mirror N00524700211 N00525000442 The vanity mirror is located on the back of the sun visor. If your vehicle is equipped with mirror lights, opening the lid (A) of the vanity mirror will automatically turn on the mirror lights (B). To use a “plug-in” type accessory, open the cover located in front of the floor console, then insert the plug in the socket.
BK0121200US.book 123 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Digital clock (if so equipped) NOTE N00525100209 When the ignition switch is in the “ACC” or “ON” position, the time is displayed. ● If the battery cables are disconnected or the battery becomes discharged, the clock will have to be reset. How each button works: Set the time by pressing the various buttons as described below. 3 H (HOUR)- Press and hold the “H” button until the correct hour appears.
BK0121200US.book 124 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls HomeLink® Wireless Control System (if so equipped) N00554300027 HomeLink® Wireless Control System is a registered trademark of Johnson Controls Inc.. HomeLink® provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® will operate most radio frequency devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
BK0121200US.book 125 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Programming HomeLink® To program HomeLink® to operate a garage door, gate, or entry door opener, home or office lighting, you need to be at the same location as the device. 2. Press and hold the 2 outer HomeLink® buttons (A) (to clear the memory) until the indicator light (B) blinks slowly (after 20 seconds). Release both buttons. 3.
BK0121200US.book 126 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls 6. If the indicator light on HomeLink® blinks rapidly for 2 seconds and then turns solid, HomeLink® has picked up a “rolling code” garage door opener signal. Now continue with the next steps to train HomeLink® to complete the programming. 7. Press and release the “smart” or “learn” program button located on the garage door opener’s motor to activate the “training mode”.
BK0121200US.book 127 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls If you continue to have programming difficulties, please contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. Clearing the programmed information To clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds) individual buttons cannot be cleared.
BK0121200US.book 128 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Interior lights Reading lights N00525300445 Dome light → P.3-129 N00525700175 Push the reading light switch (A) to turn on the light. This light produces a spot beam for convenient use as a map light. Reading lights → P.3-128 3 Push the reading light switch again to turn the light off. The reading light comes on when any door is opened.
BK0121200US.book 129 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● If the ignition key is removed with the doors closed, the interior lights come on for 30 seconds, then go off. ● The time until the light goes off can be adjusted. See your authorized Mitsubishi Motors dealer for details. For vehicles equipped with the Mitsubishi Multi-Communication System, adjustments can be made using screen operations. For details, refer to the separate owner’s manual.
BK0121200US.book 130 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls NOTE ● If the ignition key is removed with the doors closed, the interior lights come on for 30 seconds, then go off. ● The time until the light goes off can be adjusted. See your authorized Mitsubishi Motors dealer for details. For vehicles equipped with the Mitsubishi Multi-Communication System, adjustments can be made using screen operations. For details, refer to the separate owner’s manual.
BK0121200US.book 131 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Glove compartment Accessory boxes N00526400443 Convenient storage space is located throughout the vehicle. N00526500242 To open, pull the lever (A). 3 1- Glove compartment 2- Floor console box/Tissue holder/Pen holders NOTE ● When the light switch is set in either the “ ” or “ ” position, the glove compartment light illuminates.
BK0121200US.book 132 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Floor console box/Tissue holder/Pen holders N00526600168 Floor console box The floor console box is located under the arm rest. To open the console box, lift the lever (A) and raise the arm rest (B). 3 3-132 Tissue holder/Pen holder The tissue holder (A) and pen holders (B) are located on the back of the arm rest.
BK0121200US.book 133 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Cup holder For the rear seat N00527300263 For the front seat The cup holder is located in the middle of the floor console. The cup holder is designed for holding cups or drink-cans securely in its holes. N00537000032 This cup holder is located in the rear seat arm rest (A). Pull the rear arm rest down to use the cup holder. 3 ! CAUTION ● Do not drink beverages while driving your vehicle.
BK0121200US.book 134 ページ 2010年4月14日 水曜日 午前11時24分 Features and controls Coat hook Luggage hooks N00528500220 N00553600036 There are four hooks on the side of the trunk for use in securing luggage. There is a hook on the rear driver’s side assist grip for use in hanging clothes. 3 NOTE ● Do not hang heavy luggage {more than about 6.6 pound (3 kg)} on the hook. Doing so could damage the hook. 3-134 ! WARNING ● Do not put a hanger or any heavy or pointed object on the coat hook.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Fuel economy. . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- 2 Driving, alcohol and drugs. . . . . . . . . . . . . . . . . . .4- 2 Vehicle preparation before driving. . . . . . . . . . . . .4- 3 Safe driving techniques . . . . . . . . . . . . . . . . . . . . .4- 5 Driving during cold weather . . . . . . . . . . . . . . . . .4- 5 Braking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- 6 Parking . . . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Fuel economy 4 Driving, alcohol and drugs N00628800080 N00628900010 Fuel economy is dependent on many factors. Your personal driving habits can have a significant effect on your fuel use. Several recommendations for achieving the greatest fuel economy are listed below. ● Whenever accelerating from a stop, always accelerate slowly and smoothly. ● When parked for even a short period, do not idle the engine. Shut it off.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Vehicle preparation before driving N00629000597 For a safer and more enjoyable trip, always observe the following: Seat belts and seats ● Before starting the vehicle, make certain that you and all passengers are seated and wearing their seat belts properly (with children in the rear seat, in appropriate restraints), and that all the doors are locked.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Tires Check all the tires for heavy tread wear or uneven wear patterns. Look for stones, nails, glass, or other objects stuck in the tread. Look for any tread cuts or sidewall cracks. Check the wheel nuts for tightness, and the tires (including spare tire) for proper pressures. Replace your tires before they are heavily worn out.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Safe driving techniques Driving during cold weather N00629200052 N00629400272 Even this vehicle’s safety equipment, and your safest driving, cannot guarantee that you can avoid an accident or injury. However, if you give extra attention to the following areas, you can better protect yourself and your passengers: ● Drive defensively. Be aware of traffic, road and weather conditions.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety ● Check the engine antifreeze. If there is not enough coolant because of a leak or from engine overheating, add high-quality ethylene glycol antifreeze and water. The recommended blend is about 50 % water and 50 % anti-freeze. Use a higher concentration (not over 60 %) when the outside temperature is -31 °F (-35 °C) or lower.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Parking Where you park N00629600229 Parking on a hill When parking on a hill, set the parking brake, and turn the front wheels toward the curb on a downhill, or away from the curb on an uphill. If necessary, apply chocks to wheels. Be sure that the parking brake is firmly set when parked and that the selector lever is in the “P” (PARK) position.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Loading information N00629900381 It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo and non-factoryinstalled options. The tire and loading information placard located on the driver’s door sill of your vehicle will show how much weight it may properly carry. ! WARNING ● Never overload your vehicle.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Tire and loading information placard N00630100211 The tire and loading information placard is located on the driver’s door sill. This placard shows the maximum number of occupants permitted to ride in your vehicle as well as “the combined weight of occupants and cargo” (C), which is called the vehicle capacity weight. This placard also tells you the size and recommended inflation pressure for the original equipment tires on your vehicle.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Type 2 Steps for Determining Correct Load Limit N00630200065 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety NOTE ● The following table shows examples on how to calculate total cargo/load capacity of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load capacity of your vehicle. ● For the following example the combined weight of occupants and cargo should never exceed 865 lbs (392 kg).
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Cargo loads N00629700419 Cargo load precautions To determine the cargo load capacity for your vehicle, subtract the weight of all vehicle occupants from the vehicle capacity weight. For added information, if needed, refer to “Step for Determining Correct Load Limit” on page 4-10.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 Driving safety Trailer towing N00629800061 4 ! WARNING ● Do not use this vehicle for trailer towing. It may not be possible to maintain control or adequate braking.
BK0121200US.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Manual air conditioning (if so equipped). . . . . . . .5Automatic air conditioning (if so equipped) . . . . .5Important air conditioning operating tips . . . . . . .5Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5AM/FM electronically tuned radio with CD player-Type 1 (if so equipped) . . . . . . . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Vents Air flow and direction adjustments N00730200053 N00729900193 Center/Side vents Adjust the direction of the air flow by moving the knob (A). Center vents 5 Side vents 1- Center vents 2- Side vents NOTE ● Do not place beverages on top of the instrument panel. If they splash into the air conditioning vents, they could damage the system. 5-2 NOTE ● On rare occasions, air from the vents of an air-conditioned vehicle may be foggy.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Changing the mode selection Foot/Face position N00736400507 To change the position and amount of air flowing from the vents, turn the mode selection dial. (Refer to “Mode selection dial” on page 5-7, 5-15.) These symbols are used in the next several illustrations to demonstrate the quantity of air coming from the vents.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Foot position Foot/Defroster position Air flows mainly to the leg area. Air flows to the leg area, the windshield and the door windows. NOTE ● With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the leg area. With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the windshield and door windows.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Manual air conditioning (if so equipped) Defroster position Air flows mainly to the windshield and the door windows. N00730300139 The air conditioning can only be used while the engine is running. Control panel N00730500232 NOTE ● When the mode selection dial is set to the “ ” or “ ” position, the air conditioning compressor runs automatically. The outside air position will also be selected automatically.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Blower speed selection dial Temperature control dial N00736500159 N00736600118 When the ignition key is in the ON position, select the blower speed by turning the blower speed selection dial. The blower speed will gradually increase as the dial is turned to the right. When the blower speed selection dial is set to the “OFF” position, all fan-driven airflow will stop. Turn the temperature control dial clockwise to make the air warmer.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Mode selection dial Air selection switch N00736700076 N00736800338 To change the position and amount of air flowing from the vents, turn the mode selection dial. (Refer to “Changing the mode selection” on page 5-3.) Normally, use the outside position to keep the windshield and side windows clear and to quickly remove fog or frost from the windshield. To change the air selection, simply press the air selection switch.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE 5 ● When the “ ” or “ ” position is selected, you cannot turn the air conditioning off or use the recirculation position. This prevents the windows from fogging up. ● When the mode selection dial is set to a position other than “ ” or “ ”, the air selection will automatically change to outside air. The air conditioning will revert to the previous condition in which the “ ” or “ ” position was not selected.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE ● If a problem is detected in the air conditioning compressor, the air conditioning indicator light (A) blinks. Press the air conditioning switch once to turn it off, then once more to turn it back on. If the air conditioning indicator light does not blink, there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Cooling NOTE N00731200294 For ordinary cooling 5 1. Set the mode selection dial to the “ ” position. 2. Set the air selection switch (A) to the outside position. 3. Push the air conditioning switch (B). 4. Change the temperature by turning the control dial clockwise or counterclockwise. 5. Select the desired blower speed.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls For quick cooling Combination of unheated air and heated air N00731300237 Select the mode selection dial to the positions shown in the illustration and set the air selection switch (A) to the outside position. The air flow will be directed to the leg area and the upper part of the passenger compartment. Select the desired blower speed.
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Defrosting or defogging the windshield and door windows N00731400498 ! CAUTION For ordinary defrosting Use this setting to keep the windshield and door windows clear of mist, and to keep the leg area heated (when driving in rain or snow). ● For safety, make sure you have a clear view through all the windows. To remove frost or fog from the windshield and door windows, use the mode selection dial (“ ” or “ ”). 5 1.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls For quick defrosting Automatic air conditioning (if so equipped) N00731500095 The air conditioning can only be used while the engine is running. Control panel N00711800513 1. Set the mode selection dial to the “ ” position. 2. Set the blower to the maximum speed. 3. Set the temperature to the highest position. 5 NOTE ● When the mode selection dial is set to the “ ” or “ ” position, the air conditioning compressor runs automatically.
BK0121200US.book 14 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE ● There is an interior air temperature sensor (A) in the illustrated position. Never place anything over the sensor, since doing so will prevent it from functioning properly. 5 5-14 Blower speed selection dial N00736900140 When the ignition key is in the ON position, select the blower speed by turning the blower speed selection dial. The blower speed will gradually increase as the dial is turned to the right.
BK0121200US.book 15 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Temperature control dial Mode selection dial N00737000294 N00737100194 Turn the temperature control dial clockwise to make the air warmer. Turn it counterclockwise to make the air cooler. To change the position and amount of air flowing from the vents, turn the mode selection dial. (Refer to “Changing the mode selection” on page 5-3.
BK0121200US.book 16 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Air selection switch N00737200326 Normally, use the outside position to keep the windshield and side windows clear and to quickly remove fog or frost from the windshield. To change the air selection, simply press the air selection switch.
BK0121200US.book 17 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Air conditioning switch NOTE N00737300330 Push the switch, and the air conditioning compressor will turn on. The air conditioning indicator light (A) will come on. ● If a problem is detected in the air conditioning compressor, the air conditioning indicator light (A) blinks. Press the air conditioning switch once to turn it off, then once more to turn it back on.
BK0121200US.book 18 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Operating the air conditioning system (automatic mode) N00731700329 5 In normal conditions, use the system in the AUTO mode and follow these procedures: 1. Set the blower speed selection dial to the “AUTO” position. 2. Select the temperature control dial to the desired temperature. The temperature can be set within a range of around 61 to 89. The temperature may be set higher by turning the dial to the right. 3.
BK0121200US.book 19 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Operating the air conditioning system (manual mode) N00731800027 Blower speed and vent mode may be controlled manually by setting the blower speed selection dial and the mode selection dial to the desired positions. To return to automatic operation, set the dials to the “AUTO” position.
BK0121200US.book 20 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls For quick defrosting To stop the air conditioning N00732500210 To turn the air conditioning off, set the blower speed selection dial to the “OFF” position. All operations will stop except the air selection. 5 1. Set the mode selection dial to the “ ” position. 2. Set your blower to the maximum speed. 3. Set the temperature to the highest position.
BK0121200US.book 21 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Important air conditioning operating tips N00733700150 1. Park the vehicle in the shade whenever possible. Parking in the hot sun makes the vehicle interior extremely hot which then requires more time to cool. If it is necessary to park in the sun, open the windows for the first few minutes of air conditioning to expel the hot air. 2. Afterwards, keep the windows closed when the air conditioning is in use.
BK0121200US.book 22 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Audio system N00734301020 Your vehicle is equipped with the following audio system: (1) AM/FM electronically tuned radio with CD player (Type 1) → P.5-24 (2) AM/FM electronically tuned radio with CD autochanger (Type 2) → P.5-37 (3) AM/FM/Satellite electronically tuned radio with CD autochanger (Type 3) → P.5-37 The audio system can only be used when the ignition switch is in the “ON” or “ACC” position.
BK0121200US.book 23 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE ● In vehicles with AM/FM electronically tuned radio with CD autochanger (Type 2), AM/FM/Satellite electronically tuned radio with CD autochanger (Type 3), the display automatically switches to an audio indication when an audio system adjustment is made. The display automatically reverts to its original indication about 10 seconds after the audio system adjustment is finished.
BK0121200US.
BK0121200US.book 25 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To adjust the volume N00712000033 VOL (Volume control) Turn the VOL knob (2) clockwise to increase the volume; counterclockwise to decrease the volume. The status will be displayed in the display (4). 5 NOTE ● The volume control mode will shut off automatically if either the radio or CD is selected, or if no adjustment is made within about 2 seconds.
BK0121200US.book 26 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To adjust the tone N00712100340 1. Press the AUDIO switch (3) repeatedly to select the tone or balance control to change. The order is: BASS → TRE → FADE → BAL → Audio adjust mode off. The status will be displayed in the display (4).
BK0121200US.book 27 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls 2. Turn the AUDIO switch (3) either clockwise or counterclockwise to change the tone/balance setting. Mode Adjusting operation Clockwise Counterclockwise BASS Increase Decrease TRE Increase Decrease FADE More sound from the rear speakers More sound from the front speakers BAL More sound from the right speakers More sound from the left speakers BASS (Bass tone control) To select the desired bass level.
BK0121200US.
BK0121200US.book 29 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to the radio N00735000825 1. Press the PWR switch (1) to turn the audio system on and off. The system turns on in the last mode used. 2. Press the RADIO button (3) to select the desired band (AM/FM1/FM2). 3. Press the SEEK button (4 or 5) to tune to a station, or press one of the memory select buttons (2) to tune in to a station memorized for that button. To store a frequency in the memory, follow these steps: 1.
BK0121200US.
BK0121200US.book 31 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to a CD To listen an MP3 CD N00735501016 1. Press the CD button (5) and the CD mode will be selected, starting a playback. 2. To adjust the volume and tone, refer to “To adjust the volume” on page 5-25 and “To adjust the tone” on page 5-26. 3. To stop the CD, turn off the power by pressing the PWR switch (1) or switch to the other mode by pressing the RADIO button (4).
BK0121200US.book 32 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Folder selection order/MP3 file playback order (Example) NOTE 5 ● While listening to a disc on which CD-DA (CD-Digital Audio) and MP3 files have both been recorded, you can switch between reading of the CD-DA and reading of the MP3 files, and the external audio input mode by pressing the CD button for 2 seconds or longer (until you hear a beep).
BK0121200US.book 33 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To fast forward/reverse the disc To select a desired folder (MP3 CDs only) To fast forward or reverse, use the TRACK button (6 or 7). You can select your desired folder by turning the TUNE/FOLDER switch (10). Fast forward You can fast forward by holding down the side of the TRACK button (6) for more than about 1 second. Fast reverse You can fast reverse by holding down the side of the TRACK button (7) for more than about 1 second.
BK0121200US.book 34 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To select a desired track You can select by using the TRACK button (6 or 7). Track up Press the side of the TRACK button (6) until the desired track is reached. The TRACK indicator (15) will display the number of the selected track. Track down Press the side of the TRACK button (7) until the desired track is reached. The TRACK indicator (15) will display the number of the selected track.
BK0121200US.book 35 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Random playback for all folders on a disc (MP3 CDs only) Select the RDM mode, and the RDM indicator (12) will come on. Tracks from all the folders on the disc will be played in a random sequence. NOTE ● With a disc that contains both CD-DA and MP3 files, the random mode causes only files of the same format (CDDA only or MP3 files only) to be played in a random sequence.
BK0121200US.book 36 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To find the start of each track on a disc for playback Press the SCAN button (9). “SCAN” will appear on the display and the player will play back the first 10 seconds of each track on the selected disc. The track number will blink while the scan mode is selected. To exit the scan mode, press the SCAN button again.
BK0121200US.
BK0121200US.book 38 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To adjust the volume To adjust the tone N00712000381 N00712100643 Turn the VOL knob (2) clockwise to increase the volume; counterclockwise to decrease the volume. The status will be displayed in the display (5). 1. Press the AUDIO switch (4) repeatedly to select your desired sound customization setting to change. The order is: SUB GAIN → BASS → MID → TRE → FADE → BAL → FIELD → TYPE → SOUND PRESET → Sound customization mode off.
BK0121200US.book 39 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls 2. Turn the AUDIO switch (4) either clockwise or counterclockwise to adjust the sound customization features. Mode Adjusting operation MID (Midrange tone control) To select the desired midrange level. TRE (Treble tone control) To select the desired treble level. Clockwise Counterclockwise SUB GAIN Increase Decrease BASS Increase Decrease To balance the volume from the F (front) and the R (rear) speakers.
BK0121200US.book 40 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls TYPE (Music type select) To select the desired equalizer type. Music type Description NONE Sounds good for all types of music. POP Tight bass and high frequency sound ROCK Tuned for hard rock and heavy metal with powerful drums, guitars, and vocals.
BK0121200US.book 41 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Speed Compensated Volume function N00752200226 Speed Compensated Volume function is a feature that automatically adjusts the VOL, BASS, MID, and TREBLE settings in accordance with the vehicle speed. It is possible to turn this function ON-OFF using the following methods: 1. If you are presently pushing the AUDIO switch (4) and making a tone adjustment, finish making the tone adjustment. 2.
BK0121200US.
BK0121200US.book 43 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to the radio N00735000870 1. Press the PWR switch (1) or RADIO button (3) to turn on the radio. Press the PWR switch again to switch it off. 2. Press the RADIO button (3) to select the desired band (AM/FM1/FM2). 3. Press the SEEK button (4 or 5) to tune to a station, or press one of the memory select buttons (2) to tune in to a station memorized for that button. To store a frequency in the memory, follow these steps: 1.
BK0121200US.
BK0121200US.book 45 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to the radio N00735000883 1. Press the PWR switch (1) or RADIO button (3) to turn on the radio. Press the PWR switch again to switch it off. 2. Press the RADIO button (3) to select the desired band (AM/FM1/FM2/SAT1/SAT2/SAT3/SAT4). 3. Press the SEEK button (4 or 5) to tune to a station, or press one of the memory select buttons (2) to tune in to a station memorized for that button.
BK0121200US.book 46 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls SIRIUS Satellite Radio control panel and display-Type 3 N00700200243 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
BK0121200US.book 47 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to SIRIUS Satellite Radio Channel selection N00700300026 1. If the audio system is OFF, turn it ON by pushing the PWR switch (1). The audio system will start working in the previously used mode. Push the RADIO button (2) to turn ON the radio. 2. Push the RADIO button (2) to select your desired band (SAT1/SAT2/SAT3/SAT4).
BK0121200US.book 48 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE ● Once you have stored channels in memory, you can instantly call up a desired channel by just pushing the corresponding memory select buttons (7). SIRIUS ID indication N00700800047 If you push the SEEK button (3 or 4) to select “CH 0”, the SIRIUS ID will be indicated. 1. If you select “CH 0”, the first 4 digits of the 12-digit SIRIUS ID will be indicated 2 seconds later. 2.
BK0121200US.book 49 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To skip or lock a desired channel using the MENU mode N00701100047 It is possible to make a setting to skip or lock a desired channel during channel selection. 1. If you push the AUDIO switch (6) for at least about two seconds while the system is receiving a satellite radio channel, the system will switch to MENU mode. 2.
BK0121200US.book 50 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To skip a desired channel N00701500041 It is possible to set a channel to not be received during channel selection. 1. Select the channel you wish to be skipped. 2. Push the AUDIO switch (6) for at least about 2 seconds to select the MENU mode. Then select the SKIP setting mode. 3. In the SKIP setting mode, turn the AUDIO switch (6) to select “SKIP”. 4.
BK0121200US.book 51 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To unlock locked channels N00701700056 You can unlock one or all locked channels. Unlocking one or more channels requires entry of the code. 5. Use the memory select buttons (7) to enter the code (1111 to 6666). NOTE ● The code is set to “1111” at the factory. ● It is possible to change the code to any desired number using “CODE EDIT”. 1. If you wish to unlock a single desired channel, select the channel you wish to unlock.
BK0121200US.book 52 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To change the lock cancellation code 5 To reset the lock cancellation code N00701800057 N00701900045 It is possible to change the code for lock cancellation to any desired number. 1. Push the AUDIO switch (6) for at least about 2 seconds to select the MENU mode. Then select the LOCK setting mode. 2. In the LOCK setting mode, turn the AUDIO switch (6) to select “CODE EDIT”. 3. Push the AUDIO switch (6).
BK0121200US.
BK0121200US.book 54 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To listen to a CD To set a disc N00735501029 1. Press the CD button (6) and the CD mode will be selected, starting a playback. The indicator light (A) shows the condition of each disc slot. NOTE ● As many as 6 CDs can be inserted into the CD autochanger. 2. To adjust the volume and tone, refer to “To adjust the volume” on page 5-38 and “To adjust the tone” on page 5-38. 3.
BK0121200US.book 55 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls NOTE ● When the first disc has played to the end, the second disc will start to play automatically. When the second, third, fourth, fifth, and sixth discs have each played to the end, the sequence will begin again from the first disc.
BK0121200US.book 56 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Folder selection order/MP3 file playback order (Example) NOTE 5 ● While listening to a disc on which CD-DA (CD-Digital Audio) and MP3 files have both been recorded, you can switch between reading of the CD-DA and reading of the MP3 files, and the external audio input mode by pressing the CD button for 2 seconds or longer (until you hear a beep).
BK0121200US.book 57 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To fast forward/reverse the disc To select a desired folder (MP3 CDs only) To fast forward or reverse, use the TRACK button (7 or 8). You can select your desired folder by turning the TUNE/FOLDER switch (11). Fast forward You can fast forward by holding down the side of the TRACK button (7) for more than about 1 second. Fast reverse You can fast reverse by holding down the side of the TRACK button (8) for more than about 1 second.
BK0121200US.book 58 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To select a desired track You can select by using the TRACK button (7 or 8). Track up Press the side of the TRACK button (7) until the desired track is reached. The TRACK indicator (14) will display the number of the selected track. Track down Press the side of the TRACK button (8) until the desired track is reached. The TRACK indicator (14) will display the number of the selected track.
BK0121200US.book 59 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Random playback for all folders on a disc (MP3 CDs only) Select the RDM mode, and the RDM indicator (16) will come on. Tracks from all the folders on the currently selected disc will be played in a random sequence. NOTE ● The Random playback mode will be canceled by pressing the SCAN button (10) or the LOAD/EJECT button (1).
BK0121200US.book 60 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To find the start of each track on a disc for playback Press the SCAN button (10). “SCAN” will appear on the display and the autochanger will play back the first 10 seconds of each track on the selected disc. The track number will blink while the scan mode is selected. To exit the scan mode, press the SCAN button again.
BK0121200US.book 61 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls To activate the external audio input mode 1. Connect the headphone port of the portable audio system to the auxiliary audio connector (A) using a commercially available connection cord. 2. Press the CD button (B) for more than 2 seconds. The display (C) will show “AUX” and then the external audio input mode will be activated. 3.
BK0121200US.book 62 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Steering wheel remote control switch (if so equipped) N00714800312 The remote control switches are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. These switches can be used when the ignition switch is in the “ON” or “ACC” position. NOTE ● Do not push two or more of the steering wheel remote control switches at the same time.
BK0121200US.book 63 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Automatic radio tuning Seek up button — 1/Seek down button — 5 After pressing these buttons, reception of the selected station will begin. Category selection (vehicle with satellite radio) Seek up button — 1/Seek down button — 5 Keep one of the buttons pressed to scan through the categories. When your desired category is reached, release the button.
BK0121200US.book 64 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Error codes N00736100722 If an error code (1) appears in the display, take action in accordance with the table below. 5 Error display No DISC Description Repair No disc inserted Disc is not in CD player. E 01 Focus error Disc is not loaded correctly, or condensation Insert disc with label facing up. on disc. Remove moisture from disc. E 02 Disc error Disc is dirty, scratched, or deformed; or excessive vehicle vibration.
BK0121200US.book 65 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Error display Problem Description Repair E HOT High temperature Internal protection against high temperatures. Allow radio to cool by waiting about 30 minutes. E Com Communication or power supply error Communication error between external device and audio equipment. Power supply error of external device. Bring your vehicle to your authorized Mitsubishi Motors dealer or a repair facility of your choice for repair.
BK0121200US.book 66 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Error codes (SIRIUS Satellite Radio) N00736100735 If an error code (1) appears in the display, take action in accordance with the table below. 5 Error display ANT LINKING Problem 5-66 Repair Antenna error Take the vehicle to your authorized The antenna may be faulty, not securely conMitsubishi Motors dealer or a repair facility nected, or open-circuited. of your choice. Cannot pick up signal. The signal is too weak to be received.
BK0121200US.book 67 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Error display Problem Description Repair _____ (Underscore) Channel is invalid No program is currently being broadcast on Consult SIRIUS Satellite Radio at 888-539this channel; or reception is not possible SIRIUS. with this channel. SAT E Mechanical fault or bad connection Take the vehicle to your authorized There is a mechanical fault or a bad connecMitsubishi Motors dealer or a repair facility tion. of your choice.
BK0121200US.book 68 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Handling of compact discs N00734100223 ● Use only the type of compact discs that have the mark shown in the illustration below. (Playback of CD-R or CD-RW discs may cause problems.) 5 ● The use of special shaped, damaged compact discs (like cracked discs) or low-quality compact discs (like warped discs or burrs on the discs) such as those shown will damage the CD player.
BK0121200US.book 69 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls ● In the following circumstances, moisture can form on compact discs and inside the audio system, preventing normal operation. • When there is high humidity (for example, when it is raining). • When the temperature suddenly rises, such as right after the heater is turned on in cold weather. In this case, wait until the moisture has had time to dry out.
BK0121200US.book 70 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls ● Do not put additional labels (A) or stickers (B) on compact discs. Also, do not use any compact disc on which a label or sticker has started to peel off or any compact disc that has stickiness or other contamination left by a peeledoff label or sticker. If you use such a compact disc, the CD player may stop working properly and you may not be able to eject the compact disc.
BK0121200US.book 71 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Antenna N00734200325 Satellite radio antenna (if so equipped) The antenna is located as shown in the illustration. Glass antenna The antenna is embedded in the inner side of the rear window glass. 5 NOTE ● When the rear window glass is cleaned, wipe the glass with a soft cloth by moving the cloth along the antenna so as not to damage it.
BK0121200US.book 72 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls General information about your radio Weak reception (fading) Your vehicle’s radio receives both AM and FM stations. The quality of your reception is affected by distance, obstacles, and signal interference. Because of the limited range of FM signals and the way FM waves transmit, you may experience weak or fading FM reception. When the broadcast is blocked by mountains or similar obstructions, reception can be disturbed.
BK0121200US.book 73 ページ 2010年4月14日 水曜日 午前11時24分 Comfort controls Cross modulation Causes of disturbances If one listens to a weak station and is in the vicinity of another strong station, both stations might be received simultaneously. FM reception is affected by the electrical systems of vehicles in the vicinity, especially those without an electronic noise suppression device. The disturbance is even greater if the station is weak or poorly tuned.
BK0121200US.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies If the vehicle breaks down . . . . . . . . . . . . . . . . . . .6- 2 Jump-starting the engine . . . . . . . . . . . . . . . . . . . .6- 2 Engine overheating . . . . . . . . . . . . . . . . . . . . . . . .6- 5 Tools and jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .6- 7 How to change a tire . . . . . . . . . . . . . . . . . . . . . . .6- 9 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies If the vehicle breaks down Jump-starting the engine N00836300174 N00836400696 If your vehicle breaks down on the road, move to the shoulder and turn on the hazard warning flashers. If there is no shoulder, or the shoulder is not safe, drive in the right lane slowly, with the hazard lights flashing, until you come to a safe stopping place. Keep the flashers flashing.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 3. You could be injured if the vehicles move. Set the parking brake firmly on each vehicle. Put an automatic transaxle in “P” (PARK) or a manual transaxle in “N” (Neutral). Turn the ignition key to the “LOCK” position. ! 5. Connect one end of one jumper cable to the positive (+) terminal of the discharged battery (A), and the other end to the positive (+) terminal of the booster battery (B).
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 6. Connect one end of the other jumper cable to the negative (-) terminal of the booster battery (B), and the other end to the engine block of the vehicle with the low battery (A) at the point farthest from the battery. ! WARNING ● Be sure to follow the proper order when connecting the batteries, of: → → → . ● Make sure that the connection is made to the engine properly.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies Engine overheating Low battery charge If you drive your vehicle with a low battery charge after the engine has been started by using jumper cables, the engine may misfire. This can cause the anti-lock braking system warning light to blink on and off. This is only due to the low battery voltage. It is not a problem with the brake system. If this happens, fully charge the battery and ensure the charging system is operating properly.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 5. If you do not see steam or spray coming from under the hood, leave the engine on until the temperature indicator on the instrument panel moves below the red zone. When it is in the middle of the normal zone, you can start driving again. If the indicator stays in the red zone, turn off the engine. ! WARNING ● Before raising the engine hood, check to see if there is steam or spray coming from under the hood.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 9. Start the engine, and slowly add coolant, up to the bottom of the filler neck. Use plain water if you have to (and replace it with the right coolant as soon as possible). 10. Replace the radiator cap and tighten it fully. Check the temperature indicator. You can drive when the indicator returns to the normal zone. 11. Have your vehicle checked by your authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies Tools Jack N00832600153 N00832700226 To store Retract the jack, then return it to its original position.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies How to change a tire N00836900806 5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks (A) at the tire that is diagonally opposite from the tire (B) you are changing. Before changing a tire, first stop your vehicle in a safe, flat location. 1. Park the vehicle on level and stable ground. 2. Set the parking brake firmly, move the selector lever to the “P” (PARK) position. 3.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies NOTE ● The chocks shown in the illustration do not come with your vehicle. It is recommended that you purchase chocks or blocks and keep them in the vehicle for use if needed. ● If chocks or blocks are not available, use stones or any other objects that are large enough to hold the wheel in position. 6. Get the jack, bar and wheel nut wrench ready. Refer to “Tools and jack” on page 6-7.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies ! CAUTION ● Do not put the compact spare tire on a different wheel, and do not put standard tires, snow tires, wheel covers or trim rings on the compact spare wheel. Otherwise, you could damage these parts or other parts on your vehicle. To remove the spare tire N00849700202 1. Lift up the luggage floor board. 2. Remove the jack storage box. 3. To remove the spare tire, remove the installation clamp (A) by turning it counterclockwise.
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies NOTE ● Put the spare tire under the vehicle body near the jack. This makes it safer if the jack slips out of position. 6 6-12 To change a tire N00849800317 1. On vehicles with wheel covers, first remove the covers (refer to “Wheel covers” on page 6-19). Then loosen the wheel nuts with the wheel nut wrench. Do not remove the wheel nuts yet.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 2. Place the jack under one of the jacking points (A) shown in the illustration. Use the jacking point closest to the tire you wish to change. ! 3. Rotate the jack by hand until the flange portion (B) fits in the groove (C) at the top of the jack. WARNING ● Set the jack only at the positions shown here. If the jack is set at a wrong position, it could dent your vehicle or the jack might fall over and cause personal injury.
BK0121200US.book 14 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 4. Insert the bar (D) into the wheel nut wrench (E). Then put the end of the bar into the shaft’s jack end, as shown in the illustration. Slowly rotate the wheel nut wrench until the tire is raised slightly off the ground surface. ! WARNING ● No one should be in your vehicle when using the jack. ● Do not start or run the engine while your vehicle is on the jack. ● Do not turn the raised wheel.
BK0121200US.book 15 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 6. Clean out any mud, etc. on the hub surface (F), hub bolts (G) or in the installation holes (H) in the wheel, and then mount the spare tire. ! WARNING ● Mount the spare wheel with the valve stem (I) facing outboard. If you cannot see the valve stem (I), you have installed the wheel backwards. Operating the vehicle with the spare wheel installed backwards can cause vehicle damage and result in an accident.
BK0121200US.book 16 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 7. [Vehicle with steel wheels] Install the wheel nuts (tapered nuts) with their tapered ends facing inward, then tighten by hand until the wheel is no longer loose. Steel wheels (Normal wheels and compact spare wheel) 6 6-16 [Vehicle with aluminum wheels] • Normal wheels Temporarily tighten the wheel nuts (flange nuts) until their flange section comes in contact with the wheel and it is no longer loose.
BK0121200US.book 17 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies • Compact spare wheel Install the wheel nuts with their tapered ends facing inward, then tighten by hand until the wheel is no longer loose. 8. Lower the vehicle slowly by rotating the wheel nut wrench counterclockwise until the tire touches the ground. Compact spare wheel ! CAUTION ● Never apply oil to either the wheel bolts or the nuts or they will tighten too much.
BK0121200US.book 18 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies 9. Tighten the nuts in the order shown in the illustration until each nut has been tightened to the torque listed here. 88 to 108 N•m (65 to 80 ft-lb) ! 6 CAUTION ● Never use your foot or a pipe extension to apply added force to the wheel nut wrench when tightening the wheel nuts. If you do so, you can over-tighten the wheel nuts and damage the wheel, wheel nuts and hub bolts. 10. Lower the jack all the way and remove it. 6-18 11.
BK0121200US.book 19 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies ! CAUTION ● While the compact spare tire is stowed, the inflation pressure should be checked at least once a month to assure that it remains at the recommended inflation pressure. See the tire and loading information placard attached to the driver’s door sill. Refer to “Tire and loading information placard” on page 9-3. ● Driving with an improperly inflated tire can cause an accident.
BK0121200US.book 20 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies NOTE ● The wheel cover is made of plastic. Be careful when prying it off. ! CAUTION ● Trying to remove the wheel cover with only your bare hands can seriously injure your fingers. To install 6 Line up the air valve (A) with the valve opening (B) on the wheel cover. Then use your hand to strike around the outer edge of the wheel cover to secure it in place.
BK0121200US.book 21 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies Towing N00837000774 If your vehicle needs to be towed If towing is necessary, we recommend you to have it done by a commercial tow truck service. When towing is required, transport the vehicle using a tow truck. Incorrect towing equipment could damage your vehicle. ! CAUTION ● Do not attempt to be towed by another vehicle with a rope. There may be local regulations concerning towing in your area.
BK0121200US.book 22 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies Towing the vehicle by a tow truck ! 6 CAUTION ● This vehicle must not be towed by a tow truck using sling lift type equipment (Type A) as illustrated. Using a sling lift will damage the bumper and front end. ● If the engine or transaxle is malfunctioning or damaged, transport the vehicle with the driving wheels on a carriage (Type C, D or E) as illustrated.
BK0121200US.book 23 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies Operation under adverse driving conditions On wet roads N00837200688 If your vehicle becomes stuck in sand, mud or snow If your vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the selector lever rhythmically between “Sports mode” and “R” (REVERSE) position, while pressing lightly on the accelerator pedal. Do not rev the engine or spin the wheels.
BK0121200US.book 24 ページ 2010年4月14日 水曜日 午前11時24分 For emergencies On snowy or icy roads 6 ● When driving on a road covered with snow or ice, use snow tires. Tire chains cannot be used on your vehicle. There may be state or local regulations about using snow tires. Always check the regulations in your local area before using them. Refer to the section entitled “Snow tires” on page 7-27 and “Tire chains” on page 7-27. ● Drive slowly. Do not make sudden starts or stops, sharp turns, or slam on the brakes.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Service precautions . . . . . . . . . . . . . . . . . . . . . . . .7Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . .7Engine hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7View of the engine compartment . . . . . . . . . . . . . .7Engine oil and oil filter . . . . . . . . . . . . . . . . . . . . .7Engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Air cleaner filter. . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Service precautions N00937300156 Taking regular care of your vehicle will preserve its value and appearance as long as possible. You can do some of the maintenance work yourself, and the rest should only be performed by an authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Catalytic converter N00937400333 The catalytic converter requires you to use unleaded fuel only. Leaded gasoline will destroy the emission-control effectiveness of the converter. Normally, the catalytic converter does not require maintenance. However, it is important to keep the engine properly tuned for the converter to continue to work properly.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Engine hood Release the safety lever and lift the engine hood. N00937500480 To open Use the engine hood release lever (located under the instrument panel near the driver’s door) to unlock the engine hood. Pull the lever toward you to release the engine hood latch. NOTE ● To prevent damage to the engine hood and wipers, make sure the wipers are at resting position when you open the engine hood.
BK0121200US.book 5 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Support the engine hood with the hood prop. Insert the hood prop securely in the opening under the hood marked with an arrow. ! CAUTION ● Always insert the support prop into the hole specially made for it. Propping the engine hood at any other place could cause the prop to slip out and lead to an accident. ● The hood prop can fall out if the hood is lifted by a strong wind.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Engine oil and oil filter View of the engine compartment N00937600612 N00937700815 To check and refill engine oil It is normal for an engine to use oil. You may need to add oil between the recommended oil change intervals. Before starting the engine, check the engine oil level. Refill if necessary. To check the oil level, remove the dipstick, wipe it off, and gently insert it all the way into the crankcase.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ! CAUTION ● Overfilling the crankcase will cause oil aeration and loss of oil pressure, which could damage the engine. ! WARNING ● Used engine oil is poisonous, and can damage your skin. Prolonged and repeated contact may cause serious skin disorders, including dermatitis and cancer. Don’t let used oil touch your skin. Wash thoroughly after working with it. ● Keep used oil out of the reach of children.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance If you cannot find oils with the ILSAC certification symbol, use an API classification SM or higher oil with the following label. This mark appears on the top of the oil container and tells you two important things about the oil. Recommended engine oil viscosity Use engine oil with the proper thickness for the outdoor temperatures where you will be driving.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance To replace the oil filter The oil filter should be replaced at the time or mileage specified in the “WARRANTY AND MAINTENANCE MANUAL”. Only use high quality replacement filters on this vehicle. The manufacturer’s specifications for Genuine Mitsubishi oil filters require that the filter can withstand a pressure of 256 psi (1.8 MPa). A Genuine Mitsubishi oil filter is the best replacement filter.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance To add coolant Use Mitsubishi Genuine Coolant or an equivalent. Mitsubishi Genuine Coolant provides excellent protection against corrosion and rust formation on all metals, including aluminum, and prevents blockages in the radiator, heater, cylinder head, engine block, etc.
BK0121200US.book 11 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ● If the temperature of the engine coolant does not rise after the engine is warmed-up, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the thermostat checked, and replaced if necessary. Air cleaner filter N00937900370 The air cleaner filter will get dirty and dusty from use and not filter properly.
BK0121200US.book 12 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Automatic transaxle fluid Procedure for checking the fluid level N00938000538 The automatic transaxle should be maintained and serviced by an authorized Mitsubishi Motors dealer or a repair facility of your choice to obtain the best performance and longest life. It is important that the transaxle fluid is kept at the correct level.
BK0121200US.book 13 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Fluid type Use only “DIAMOND ATF SP III” transaxle fluid to ensure optimum transaxle performance. Special additives Mitsubishi Motors Corporation does not recommend the addition of any fluid additives to the transaxle. Washer fluid N00938600286 The windshield washer fluid reservoir is in the engine compartment. Check the washer fluid level at regular intervals and add washer fluid to reservoir if necessary.
BK0121200US.book 14 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Brake fluid Fluid type N00938800347 To check the fluid level The brake fluid level must be between the “MAX” and “MIN” marks on the reservoir. Use brake fluid conforming to DOT 3 or DOT 4. The reservoir cap must be tightly sealed to keep dirt and water out. ! CAUTION ● Do not let any petroleum-based fluid touch, mix with, or get into the brake fluid. This will damage the seals. ● Be careful when handling brake fluid.
BK0121200US.book 15 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Battery Power steering fluid N00939000320 To check the fluid level Check the fluid level in the reservoir while the engine is idling. Check to make certain that the power steering fluid level is always between the “MAX” and “MIN” level markings on the fluid reservoir and refill the fluid, if necessary.
BK0121200US.book 16 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Checking battery electrolyte level Use the following procedure to check the battery electrolyte level. 1. Insert the tip of a screwdriver at the edge of the cap, pry gently to remove the cap. 2. The inside of the battery is divided into several compartments. Check the electrolyte level (A) in each cell. The electrolyte level must be within the range (B) shown in the illustration.
BK0121200US.book 17 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance During cold weather The battery is weaker in cold temperatures. This has to do with its chemical and physical properties and is why a very cold battery, especially one with a low charge, will have a hard time starting your vehicle. It is recommended that you have your battery and charging system checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice before the start of cold weather.
BK0121200US.book 18 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ! 7 WARNING ● Never disconnect the battery while the engine is running, or you could damage the vehicle’s electrical parts. ● Never short-circuit the battery. This could cause it to overheat and be damaged. ● Keep sparks, cigarettes, and flames away from the battery because the battery could explode. ● Electrolyte (battery acid) is made of corrosive diluted sulfuric acid.
BK0121200US.book 19 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Tires N00939200537 ! WARNING ● Driving with tires that are worn, damaged or improperly inflated is dangerous. These type tire conditions will adversely affect vehicle performance. These type tire conditions can also cause a tread separation or blowout which may result in an accident causing serious injury or death. ● Tires, including spare tire, degrade over time with age even when they are not being used.
BK0121200US.book 20 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ● Cord: the strands forming the plies in the tire. ● Rim: a metal support for a tire or a tire and tube assembly upon which the tire beads are seated. ● Rim diameter: nominal diameter of the bead seat. ● Groove: the space between two adjacent tread ribs.
BK0121200US.book 21 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Size Designation Service Description EXAMPLE:P215/65R15 EXAMPLE: 95H P Passenger car tire size based on U.S.A. design standards 215 Section width in millimeters (MM.) 65 Aspect ratio in percent (%) Ratio of section height to section width of tire. R Construction code • “R” means radial construction. • “D” means diagonal or bias construction.
BK0121200US.book 22 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Maximum Pressure Maximum Pressure indicates the maximum permissible cold tire inflation pressure for this tire. Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire but the date code may only be on one side. Look for the TIN on the outboard side of tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
BK0121200US.book 23 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Tire inflation pressures N00939300798 Proper tire inflation pressure is essential for the safe and satisfactory operation of your vehicle. The wrong tire pressure will cause problems in three major areas: ● Safety Too little pressure increases flexing in the tire and can cause tire failure. Too much pressure can cause a tire to lose its ability to cushion shock.
BK0121200US.book 24 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ● Drive at safe speeds. ● After filling your tires to the correct pressure, check them for damage and air leaks. Be sure to reinstall the caps on the valve stems. Replacing tires and wheels N00939600313 ! CAUTION ● Avoid using different size tires from the one listed and the combined use of different types of tires, as this can affect driving safety. Refer to “Tires and wheels” on page 9-7.
BK0121200US.book 25 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Tread wear indicators Tire rotation N00939800171 N00939900420 To even out the wear on your tires and make them last longer, Mitsubishi Motors Corporation recommends that you rotate your tires at the mileage listed in the “WARRANTY AND MAINTENANCE MANUAL”. However, the timing for tire rotation may vary according to your vehicle condition, road surface conditions, and your own personal driving habits.
BK0121200US.book 26 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Tires that do not have arrows showing rotation direction Front Tires that have arrows showing rotation direction Front ! 7 CAUTION ● A compact spare tire can be fitted temporarily in place of a tire that has been removed during the tire rotation. However, it must not be included in the regular tire rotation sequence.
BK0121200US.book 27 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Snow tires Front N00940000359 In some areas of the country, snow tires are required for winter driving. If snow tires are required in your area, you must choose snow tires of the same size and type as the original tires provided with your vehicle. Snow tires should also be installed on all four wheels. Otherwise your safety and vehicle handling can be reduced.
BK0121200US.book 28 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Parking brake lever stroke Brake pedal free play N00940300235 N00940400177 To check the brake pedal free play (A), turn off the engine and press the brake pedal several times with your foot. Then press the pedal down with your fingers until you first feel resistance. Check the parking brake lever travel occasionally. To check this, pull the lever up slowly and count the number of clicks of the ratchet.
BK0121200US.book 29 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Emission-control system maintenance Wiper blades N00940700011 N00940800272 Check the wiper blades occasionally. Clean them regularly to remove deposits of salt and road film. Use a sponge or cloth and a mild detergent or non-abrasive cleaner to clean the blades and glass areas. Replace the blades if they continue to streak or smear.
BK0121200US.book 30 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance NOTE ● To meet government regulations and promote cleaner air, your vehicle is equipped with an onboard diagnostic system (OBD). The engine electronic control module that controls OBD functions stores various data (especially about the exhaust emissions). This data will be erased if the battery cable is disconnected, which could make a rapid diagnosis difficult.
BK0121200US.book 31 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance General maintenance Direct ozone reduction radiator (if so equipped) N00952900023 Some models are equipped with a PremAir® direct ozone reduction (DOR) radiator. ! CAUTION ● Replacement of this emission control component with a non-DOR radiator is a violation of air pollution regulation. N00941500159 The next pages list the maintenance service recommended by Mitsubishi Motors Corporation.
BK0121200US.book 32 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Ball joint, steering linkage seals and drive shaft boots N00941800080 Check the following parts for damage and grease leaks: ● Ball joint boots of the front suspension and steering linkage ● Bellows on both ends of the drive shaft Drive belt (for generator, power steering pump, air conditioning compressor) N00941900283 Check the tension of the drive belt.
BK0121200US.book 33 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Exhaust system Timing belt N00942200010 ! WARNING ● Carbon monoxide gas from your vehicle’s exhaust is poisonous. Breathing these fumes can cause unconsciousness or death. The best way to keep carbon monoxide gas from entering inside your vehicle is to have the engine exhaust system properly serviced.
BK0121200US.book 34 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Fuse links For cold and snowy weather N00942600115 Ventilation slots The ventilation slots in front of the windshield should be kept clear of leaves or brushed clear after a heavy snowfall, so that the operation of the heating and ventilation systems will not be impaired. Weatherstripping To prevent freezing of the weatherstripping on the doors, engine hood, etc., they should be treated with silicone grease.
BK0121200US.book 35 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Fuses Engine compartment N00942800263 Fuse block location In the engine compartment, the fuse blocks are located as shown in the illustration. N00901000080 To prevent damage to the electrical system from short-circuiting or overloading, each individual circuit is equipped with a fuse. The fuse blocks are located in the passenger compartment and in the engine compartment.
BK0121200US.book 36 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Type A 1. Push the lock lever. 2. Remove the fuse block cover. ! WARNING ● Do not touch the electronic control module (D). The module surface can be too hot. Wait for the electronic control module to cool down before replacing a fuse.
BK0121200US.book 37 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Type B 1. Push the lock lever. 2. Remove the relay box cover. Type C 1. Pull the lock lever. 2. Open the cover. Fuse load capacities N00954800101 This fuse list shows the names of the electrical systems and their fuse capacities. There are spare fuses in the cover of the instrument panel (driver’s side). Always replace a blown fuse with one of the same capacity as the original.
BK0121200US.book 38 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Passenger compartment fuse location table Passenger compartment fuse location No. Symbol Electrical system 1 — — — 2 — — — 3 Radio 30 A 4 Sunroof 20 A 5 Rear window defogger 30 A 6 Heater 30 A 7 — — — 8 — — — 9 Power outlet 15 A 10 Power door locks 15 A 11 — — — 12 — — — 13 Engine control 7.5 A 14 Outside rearview mirrors 7.
BK0121200US.book 39 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance No. Symbol Electrical system Capacity 22 Back-up lights 7.5 A 23 Gauge 7.5 A 24 Ignition coil 10 A 25 — Spare fuse 20 A 26 — Spare fuse 30 A 27 — Spare fuse 30 A Engine compartment fuse location table Type A Engine compartment fuse location ● Some fuses may not be installed on your vehicle, depending on the vehicle model or specifications.
BK0121200US.book 40 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance No. 7 Symbol Electrical system Capacity No. Symbol Electrical system Capacity 4 Ignition switch 40 A* 23 Radio 10 A 5 Power window control 30 A* 24 Fuel pump 15 A 6 Front fog lights/ Daytime running lights 15 A 25 Windshield wiper 30 A 7 Heated seat 20 A 8 Horn 15 A 9 Engine control 20 A 10 Air conditioning 10 A 11 Stop lights 15 A 12 Rear fog light 10 A 13 Alternator 7.
BK0121200US.book 41 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Type C Type B Engine compartment fuse location Engine compartment fuse location Front Front No. 1 Symbol Electrical system Condenser fan motor Capacity No. 20 A* 1 *: Fusible link ● Some fuses may not be installed on your vehicle, depending on the vehicle model or specifications. ● The table above shows the main equipment corresponding to each fuse.
BK0121200US.book 42 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Fuse replacement Identification of fuse N00901100065 Capacity Color 7.5 A Brown 10 A Red 15 A Blue 20 A Yellow (fuse type) / Light blue (fusible link type) 30 A Green (fuse type) / Pink (fusible link type) 7 7-42 40 A Green 60 A Yellow 80 A White N00954900043 1. Before replacing a fuse, always turn off the electrical item connected to the fuse and turn the ignition key to the “LOCK” position. 2.
BK0121200US.book 43 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 4. Clamp it on the fuse you wish to remove, and pull the fuse straight out from the fuse block. 5. Use the fuse location diagrams and the matching tables, to check the fuse that is related to the problem. If the fuse is not blown, something else must be causing the problem. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the problem checked.
BK0121200US.book 44 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 6. Insert a new fuse of the same capacity securely into the appropriate slot. ! CAUTION ● Never use a fuse with a capacity greater than the one listed or any substitute, such as wire, foil etc. This would cause the circuit wiring to heat up and could cause a fire.
BK0121200US.book 45 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Bulb capacity Outside N00950300746 N00943000044 The bulb should only be replaced with a new bulb with the same rating and type. The type and rating are listed on the base of the bulb. Front Description Wattage or ANSI Trade No.
BK0121200US.book 46 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance NOTE Rear ● The high-mounted stop light uses LEDs rather than bulbs. For repair and replacement, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. Inside N00950400532 Description 7 Wattage or ANSI Trade No.
BK0121200US.book 47 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Headlights N00943100856 1. When replacing the headlight bulb on the left side, remove the relay box. Pull the relay box (B) upward while pressing the tab (A). 2. Depress the tab (C) on the harness connector and pull the harness connector toward you to remove it.
BK0121200US.book 48 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 3. Remove the locking cap (D) by turning it counterclockwise. 4. Remove the headlight bulb (E) with holder. 5. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 49 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ! CAUTION ● Handle halogen light bulb with care. The gas inside a halogen light bulb is highly pressurized, so dropping, knocking, or scratching a halogen light bulb can cause it to shatter. ● Never hold the halogen light bulb with a bare hand, dirty glove, etc. The oil from your hand could cause the bulb to break the next time the headlights are used.
BK0121200US.book 50 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Front turn-signal and parking lights Front side-marker lights N00917300424 N00943400282 1. Turn the bulb socket counterclockwise to remove it. And remove the bulb from the socket by turning it counterclockwise while pressing in. 1. Turn the bulb socket counterclockwise to remove it. And remove the bulb from the socket by pulling out. 2. To install the bulb, perform the removal steps in reverse. 2.
BK0121200US.book 51 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Front fog lights (if so equipped) N00943600691 1. Remove the clips (A) and screws (B), then remove the cover (C). 2. Remove the socket and bulb assembly (D) by turning it counterclockwise.
BK0121200US.book 52 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 3. Pull part (E) in the direction of the arrow (F) to undo the lock, thereby freeing the fog light bulb from the connector. 4. To install the bulb, perform the removal steps in reverse. 7 7-52 ! CAUTION ● Handle halogen light bulb with care. The gas inside a halogen light bulb is highly pressurized, so dropping, knocking, or scratching a halogen light bulb can cause it to shatter.
BK0121200US.book 53 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Rear combination lights N00943700416 1. Open the lid. Partially take off the trim cover (A). 2. Remove each socket and bulb assembly by turning it counterclockwise. B- Rear turn-signal light Remove the bulb by pulling it out. C- Tail and stop light Remove the bulb by pulling it out. 3. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 54 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Back-up lights N00901200053 1. Open the trunk lid. On vehicles equipped with the trunk lid grip, remove the screws (A), and remove the trunk lid grip (B). 7 7-54 2. On vehicles equipped with the cover, remove the clips (C) by prying with a straight blade (or minus) screwdriver, and remove the cover (D).
BK0121200US.book 55 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 3. Remove the socket and bulb assembly by turning it counterclockwise. 4. Remove the bulb by pulling it out.
BK0121200US.book 56 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 5. To install the bulb, perform the removal steps in reverse. NOTE ● To reinstall the clips, first insert the prongs (F) into the hole, then firmly press the cap portion (G). 7 7-56 High-mounted stop light N00943900098 NOTE ● The high-mounted stop light uses an LED instead of a bulb. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice when the light needs to be repaired or replaced.
BK0121200US.book 57 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance License plate light N00944000373 1. Open the trunk lid. On vehicles equipped with the trunk lid grip, remove the screws (A), and remove the trunk lid grip (B). 2. On vehicles equipped with the cover, remove the clips (C) by prying with a straight blade (or minus) screwdriver, and remove the cover (D).
BK0121200US.book 58 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance 3. Open the trunk lid. Remove the socket and bulb assembly by turning it counterclockwise. 4. Remove the bulb by pulling it out. 5. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 59 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Dome light Glove compartment light (if so equipped) N00944100231 N00954200020 1. Insert the tip of a screwdriver at the edge of the lens, pry gently to remove the lens, and then remove the bulb from the light holder. Have the glove compartment light bulbs replaced at an authorized Mitsubishi Motors dealer or a repair facility of your choice.
BK0121200US.book 60 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Trunk room light Vanity mirror lights (if so equipped) N00944800081 N00952800064 1. Pull both clips (A) away from the center as shown and remove the light unit. Then remove the bulb by pulling out. 1. Insert the tip of a screwdriver at the edge of the lens, pry gently to remove the lens, and then remove the bulb from the light holder. 2. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 61 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Vehicle care precautions N00945100023 These can all be dangerous, and they all can damage your vehicle. In order to maintain the value of your vehicle, perform regular maintenance using the proper materials and procedures. Be sure to use only those materials and procedures that meet your local environmental pollution control regulations.
BK0121200US.book 62 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Cleaning the inside of your vehicle N00945200037 After washing the inside of your vehicle with any cleaner, wipe it dry in a shady, well ventilated area. ! CAUTION ● Do not use organic substances (solvents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discoloring, staining or cracking of the surface.
BK0121200US.book 63 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ● The genuine leather surface can be damaged if brushed with a nylon or synthetic fiber brush. ● Organic solvents such as benzine, alcohol, gasoline, acid or alkaline solvents can discolor the genuine leather surface and should not be used. ● Genuine leather can mildew if not kept clean. Clean up any oil stains immediately.
BK0121200US.book 64 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ! 7 CAUTION ● When washing the underside of your vehicle or the wheels, wear a pair of gloves to protect your hands. ● Never spray or splash water on the electrical parts in the engine compartment. This may damage them. Be careful also when washing the underbody. Do not spray water into the engine compartment. ● Avoid automatic car washers that use rotating brushes. These brushes may scratch the paint surface and make it dull.
BK0121200US.book 65 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance ! CAUTION ● Do not use gasoline, kerosene, benzene or paint thinners to remove road tar or other dirt from the vehicle surface. ● Do not put wax on the areas having black matte coating because it can cause uneven discoloration, patches, blurs, etc. If these get wax on them, wipe the wax off right away with a soft cloth and warm water.
BK0121200US.book 66 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Cleaning plastic parts Aluminum wheels (if so equipped) N00946300208 N00946500167 Use a sponge or chamois to clean these parts. If vehicle wax sticks to a gray or black rough surface of the bumper, moulding or lights, the surface may appear white in color. In this case, wipe it off using lukewarm water and a soft cloth or chamois. 1. Remove dirt using a sponge while sprinkling water on the wheel. 2.
BK0121200US.book 67 ページ 2010年4月14日 水曜日 午前11時24分 Vehicle care and maintenance Wiper blades Engine compartment N00946700013 N00947000042 Use a soft cloth and glass cleaner to remove grease, dead insects, etc., from the wiper blades. Replace the wiper blades when they no longer clean the windshield and rear window properly. Never spray or splash water on the electrical components in the engine compartment, as this may cause damage.
BK0121200US.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in U.S.A.) . . . . . . . . . . . . . . .8Reporting Safety Defects . . . . . . . . . . . . . . . . . . . .8Important facts to know in case of an accident . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in U.S.A.) N01047100100 This information is provided in compliance with the requirements of the National Highway Traffic Safety Administration, Department of Transportation. It provides the purchasers and/or prospective purchasers with information on reporting safety defects.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Customer assistance/Reporting Safety Defects Reporting Safety Defects N01047200387 For vehicles sold in U.S.A. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mitsubishi Motors North America, Inc.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Customer assistance/Reporting Safety Defects Important facts to know in case of an accident N01047300098 We hope you will never be involved in an accident, but there is always that potential danger. So, please be sure to buckle up and drive safely. In the event of an accident ● Remain calm. ● Check for injuries. Report all injuries to the police, and, if necessary, call for an ambulance. ● Record all the details of the accident.
BK0121200US.book 1 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Vehicle labeling . . . . . . . . . . . . . . . . . . . . . . . . . . .9Vehicle dimensions . . . . . . . . . . . . . . . . . . . . . . . .9Vehicle weights . . . . . . . . . . . . . . . . . . . . . . . . . . .9Engine specifications . . . . . . . . . . . . . . . . . . . . . . .9Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Tires and wheels. . . . . . . . . . . . . . . . . . . . . . . . . . .9Capacities. . . . . . . . .
BK0121200US.book 2 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Vehicle labeling Engine serial number N01147400638 Keep a record of the vehicle identification number. This information will assist the police if your vehicle is stolen. 1 - Vehicle emission control information label The vehicle emission control information label is affixed on the underside of the engine hood.
BK0121200US.book 3 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Tire and loading information placard Type 1 N01148100384 The tire and loading information placard is located on the driver’s door sill. Type 2 A- Vehicles sold in U.S.A.
BK0121200US.book 4 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Vehicle dimensions Certification label N01148200141 N01147500495 The certification label is located on the driver’s door sill. Overall length 191.1 in (4,853 mm) Overall width 72.4 in (1,840 mm) Overall height Wheel base 9 9-4 Vehicles with 16 inch tires 57.4 in (1,458 mm) Vehicles with 18 inch tires 57.7 in (1,465 mm) 108.
BK0121200US.
BK0121200US.book 6 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Engine specifications N01147700484 Engine model 4G69 Engine displacement 145.1 CID (2,378 cm³) No. of cylinders and cylinder arrangement 4 in-line Bore 3.43 in (87.0 mm) Stroke 3.9 in (100.0 mm) Compression ratio 9.5 Thermostat valve opening temperature Spark plugs Spark plug gap Firing order 9 9-6 NGK 188.6 °F (87.0 °C) LZFR6AI .028 to .031 in (0.7 to 0.
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Battery Tires and wheels N01147800238 BCI Group No.86 N01147900620 Tire Size Battery is a 12 volt type. NOTE ● There are various size of batteries in BCI Groups No.86. When you replace the battery, confirm the size of the replacement battery will not interfere with other components in the engine compartment. Wheel PCD Offset P215/60R16 94T P235/45R18 94V 16 x 6 1/2JJ 18 x 8J 4.5 in (114.3 mm) 1.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分 Specifications Capacities N01148000859 Item Capacity Fuel (approximate) Engine oil 17.7 gal (67.0 L) Oil pan 4.2 qt (4.0 L) Oil filter .32 qt (0.3 L) Power steering Automatic transaxle As required 8.1 qt (7.7 L) Lubricants Refer to “Fuel selection” on page 1-2. Engine oils displaying ILSAC certification mark (“starburst” symbol) on the container. If these oils are not available, an API classification SM can be used.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
BK0121200US.
MMNA_ 本文最終ページ .fm 1 ページ 2005年12月15日 木曜日 午後2時58分 How to calculate your gasoline mileage You can calculate your miles-per-gallon or kilometers-per-litre by using the following process: 1. Fill your vehicle’s fuel tank and record the odometer mileage. 2. Drive your vehicle as you normally do. 3. Refill the fuel tank. Record the odometer mileage again, as well as the gallons/litres of fuel used. 4. Subtract the first mileage number from the second number to know how many miles/kilometers were driven.
MMNA_ 表 3.