Owners Manual

ManualsBrandsMITSUBISHI ManualsAutomotiveMitsubishi L200 2011 Owners Manual.pdf

161

162

163

164

165

166

167

168

169

170

4-wheel drive operation

E00606600920

By selecting 4-wheel drive, both

axles of the vehi-

cle are rigidly connected with each other. This im-

proves the traction characteristics. When turning

sharp corners or moving forward and backward re-

peatedly, however, the drive line is stressed, which

is felt as a braking effect. A 4-wheel drive vehicle

can accelerate more quickly and smoothly.

However, note that the braking distance is not short-

er than that of a rear-wheel drive vehicle.

When using 4-wheel drive on rough roads (snow,

mud, sand, etc.), it is important to operate the vehi-

cle correctly.

NOTE

The driving posture should be more upright

and closer to the wheel than usual; adjust the

seat to a good position for easy steering and

pedal operation. Be sure to wear the seat belt.

After driving on rough roads, check each

part of the vehicle and wash it thoroughly

with water. Refer to the “Vehicle care” sec-

tion and “Inspection and maintenance follow-

ing rough road operation” on page 4-41.

Driving on dry paved road and highway

Select “2H” position (easy select 4WD), “2H” or

“4H” position (super select 4WD) to drive on the

dry paved road. Especially on dry highway, never

select the “4H” or “4L” position (easy select

4WD), “4HLc” or “4LLc” position (super select

4WD).

CAUTION

Selecting “4H” or “4L” position (easy se-

lect 4WD), “4HLc” or “4LLc” position (su-

per select 4WD) to drive on dry paved

road will increase the fuel consumption

with possible noise generation and early

tyre wear.

It may also increase the differential oil

temperature, resulting in possible dam-

age to the driving system.

Further, the drive train will be subjected

to excessive loading, possibly leading to

oil leakage, component seizure, or other

serious faults.

Driving on snowy or icy roads

Set

the transfer shift lever

to “4H” or “4L” position

(easy select 4WD), “4H” or “4HLc” position (su-

per select 4WD) in accordance with the road condi-

tions, and then gradually depress the accelerator ped-

al for a smooth start.

NOTE

The use of snow tyres and/or tyre chains is

recommended.

Maintain a safe distance between vehicles,

avoid sudden braking, and use engine brak-

ing (downshifting).

CAUTION

Avoid sudden braking, sudden accelera-

tion, and sharp turning; such operations

could cause skidding and spinouts.

Driving on sandy or muddy roads

Set the transfer shift lever

to “4H” or “4L” position

(easy select 4WD), “4HLc” or “4LLc” position (su-

per select 4WD) and then gradually depress the ac-

celerator pedal for a smooth start. Keep the pres-

sure on the accelerator pedal as constant as possi-

ble, and drive at low speed.

CAUTION

Do not force the vehicle

or drive reckless-

ly on sandy surfaces. In comparison with

normal road surfaces, the engine and oth-

er drive-system components are put un-

der excessive strain when driving on such

a surface, and this could lead to accidents.

If any of following conditions occur while

the vehicle is being driven, immediately

park your vehicle in a safe place and fol-

low these procedures:

• The needle in the temperature gauge

approaches the overheating zone.

Refer to “Engine overheating” on

page 6-04.

• Automatic transmission fluid temper-

ature warning lamp comes on.

Refer to “When the A/T (automatic

transmission) fluid temperature warn-

ing lamp comes on” on pages 4-19,

4-24.

Starting and driving

4-39

OCRE12E1