Specifications

ManualsBrandsMitsubishi ManualsOtherCP710E

COLOUR VIDEO COPY PROCESSOR

MODEL

CP710E

OPERATION MANUAL

THIS OPERATION MANUAL IS IMPORTANT

TO YOU.

PLEASE READ IT BEFORE USING YOUR

COLOUR VIDEO COPY PROCESSOR.

POWER

OPEN

REMOTE

MEMORY

MONITOR

CP710

This video copy processor complies with the requirements of the EC

Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.

The electro-magnetic susceptibility has been chosen at a level that

gains proper operation in residential areas, on business and light

industrial premises and on small-scale enterprises, inside as well as

outside of the buildings. All places of operation are characterised by

their connection to the public low voltage power supply system.

Summary of content (75 pages)

PAGE 1
COLOUR VIDEO COPY PROCESSOR MODEL CP710E OPERATION MANUAL CP710 MONITOR MEMORY PRINT POWER OPEN REMOTE THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR COLOUR VIDEO COPY PROCESSOR. This video copy processor complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
PAGE 2
. Precautions In the interest of safety, please observe the following precautions: POWER REQUIREMENT This Colour Video Copy Processor is designed for operation on 220V-240V, 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency. WARNNG: THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE. PROTECTIVE MEASURES IF ABNORMAL ARISE, .....
PAGE 3
2. Precautions BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury. Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the provided power cord and the composite video signal cable. INSTALLATION LOCATIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on the top, sides and bottom of this unit.
PAGE 4
2. Precautions CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices. SAFETY CHECKS Periods: Scope: a) According to the recommendations of the manufacturer of medical device. Visual inspection Housing, leads, controls, displays, labels/ markings, accessories, operation manual.
PAGE 5
3. Preparations before operation 1 Removing the fixed screw on the printing unit and protective cushion Pages 4-5 2 Installing the print paper and ink cassette Pages 5-8 • • Install the print paper. Install the cassette with ink sheet. 1 Removing the fixed screw on the printing unit and protective cushion When using the unit for the first time, remove the fixed screw on the printing unit and protective cushion. Remove the fixed screw on the printing unit.
PAGE 6
3. Preparations before operation Remove the protective cushion. Note: Unplug the power cord from outlet for safety. 1 Press the OPEN button on the front panel. Printing unit advances to the front. Attention • Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality. 2 Pull out the protective cushion from the right side. Attention • • Protective cushion Keep the protective cushion for transporting this unit.
PAGE 7
3. Preparations before operation 3 Insert the print paper between roller 1 and 2. 4 Insert the edge of the print paper to roller 3. Be sure to insert the paper straight. Roller 3 Roller Paper Roller Roller Paper Paper Roller 2 Roller 1 Print paper INCORRECT CORRECT INCORRECT 5 Feed the print paper through the exit slot straight with your hand. 6 Pull the print paper to eliminate slack. Note: If too much paper is fed, an error may occur. ("PAPER JAM12" is indicated on the monitor screen.
PAGE 8
3. Preparations before operation Install the ink cassette 1 Eliminate any slack of the ink sheet. Hold the roller A and B and turn the white roller. 2 Insert the ink cassette with the ink sheet into its compartment. Insert the ink cassette with the knob side toward you until it is locked into place. • When taking the ink cassette out of the compartment, press the ink cassette locking holder to release the lock. Refer to page 12. Set the printing unit 1 Push the printing unit until it is locked into place.
PAGE 9
3. Preparations before operation Print paper and ink sheet Attention • Listed below is the print paper and ink sheets available for the CP710E. Make sure you use only these consumables.
PAGE 10
4. Connection with external equipment The functions of this unit can be set with the menu screens displayed on the monitor. 1 Connection with Monitors Page 9 Explains how to connect with a monitor. 2 Connection with VIDEO/S-VIDEO (Y/C separate VIDEO) signal equipment Page 10 Explains how to connect with a video signal equipment. Explains how to connect with a S-video signal equipment.
PAGE 11
4. Connection with external equipment (VIDEO/S-VIDEO) 2 Connection with VIDEO signal, S-VIDEO (Y/C separate VIDEO) signal equipment When connecting the unit with another equipment, make sure to set the power of each equipment to "OFF".
PAGE 12
5. Features and functions 1 FRONT PANEL pages 11 - 12 Explains the buttons and terminals, etc. on the front panel. 2 INSIDE OF PRINTING UNIT page 12 Explains the installation of the ink cassette and print paper inside the unit. 3 REAR PANEL page 13 Explains input/output terminals on the rear panel. 4 REMOTE CONTROL pages 14 - 15 Explains the functions of the buttons on the remote control.
PAGE 13
5. Features and functions 6 Monitor button [MONITOR] Switches the display on the monitor. When this button is pressed, the picture on the monitor screen switches between the picture of the input signal (source image) and the memorized image. 7 MEMORY button [MEMORY] This enables memorization of the image to be printed. 8 PRINT button [PRINT] Press this button to print the images memorized by the MEMORY button. A green lamp will light during printing. The screen switches to the picture of the input signal.
PAGE 14
5. Features and functions 3 REAR PANEL 1 2 3 4 Potential equalization connector 1 This is used to equalize the potential of the 2 REMOTE equipment connected to the unit. For details, refer to the installation instruction of S-VIDEO VIDEO the equipment to be connected. AC LINE 5 1 S-VIDEO SIGNAL INPUT/OUTPUT TERMINALS [S-VIDEO] Use these terminals to connect this unit to S-VIDEO signal equipment. Refer to page 10 for connection.
PAGE 15
5. Features and functions 4 REMOTE CONTROL 1 2 DISPLAY COLOR ADJUST PROG. 3 FIELD /FRAME 9 + - A B C D E 4 PRINT Q' ty SET MENU CLEAR STOP MEMORY PAGE MONITOR MEMORY PRINT 5 6 7 8 1 COLOR IMAGE ADJUSTMENT button [COLOR ADJUST] When this button is pressed, a screen for adjusting the video image is displayed. Use this button to set the various functions of this unit. (The menus displayed on the monitor is used to set the various settings. Refer to Pages 26-27.
PAGE 16
5. Features and functions 8 PRINT button [PRINT] Press this button to print the image memorized by the MEMORY button. 9 PROGRAM button [PROG.] Press this button to select the images memorized in the program of this unit and various settings such as printing. Each time this button is pressed, the program is switched. This unit has 3 kind of programs and they can be changed and stored voluntarily. Programs cannot be changed during printing.
PAGE 17
6. Printing procedures (Basic prints) One picture image can be printed on one sheet. S size printing 1 Printing L size printing Pages 17 - 23 Explains storing an image in the memory and printing 2 Continuous printing Explains the continuous printing of the same image.
PAGE 18
6. Printing procedures (Basic prints) 1 Printing Selecting FIELD or FRAME 1 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. DISPLAY PROG. COLOR ADJUST FIELD /FRAME + PRINT Q' ty MENU FIELD/FRAME button SET CLEAR STOP • Select the FRAME mode for a high resolution still image printing. Select the FIELD mode for a picture of quickly moving objects. • When the FIELD mode is selected, the print image will be lower in resolution.
PAGE 19
6. Printing procedures (Basic prints) Selecting input signal • • Select " VIDEO " or " S-VIDEO " according to the input signal. The input signal can be set on the menu screen displayed on the monitor. • It is not necessary to select the input signal every time you print unless the input signal is changed. MENU 1 Press the MENU button . • " MAIN MENU " is displayed. 2 Press the DOWN or UP 3 Press the RIGHT shift button. shift button to select " 2. SIGNAL SET [ • " 2.
PAGE 20
6. Printing procedures (Basic prints) SET 5 Press the SET button. • " CHANGE : OK " is selected. • When changing the input signal selected at step 4 , press the RIGHT SET shift button to select " CANCEL " . Press the SET button to select "INPUT" in " 2.SIGNAL SET " again. SET 6 Press the SET button. • The MAIN MENU is displayed. SET 7 Press the SET button. • " SAVE 1/2/3 " is selected. • This menu is used to store the setting in any one of 3 programs (1, 2 or 3).
PAGE 21
6. Printing procedures (Basic prints) Setting print size (S/L) • Set the print size to "S" or "L" according to the ink sheet installed. • The print size can be set on the menu screen displayed on the monitor. • It is not necessary to set the size every time you print unless the size of the ink sheet is changed. 1 Press the MENU button. • " MAIN MENU " is displayed. 2 Press the UP PUSH [ or DOWN shift button to select" 4. PRINT ] ". 3 Press the RIGHT shift button. • " Print Menu " is displayed.
PAGE 22
6. Printing procedures (Basic prints) SET 5 Press the SET button. • " CHANGE : OK " is selected. • When changing the size setting selected at step 4 , press the RIGHT shift SET button to select " CANCEL " . Press the SET button to select "MODE : S/L" in " 4.PRINT " again. SET 6 Press the SET button. • The MAIN MENU is displayed. SET 7 Press the SET button. • " SAVE 1/2/3 " is selected. • This menu is used to store the setting in any one of 3 programs (1, 2 or 3).
PAGE 23
6. Printing procedures (Basic prints) MEMORY PAGE The following image memorization function is available. When storing one image in the memory: • When FRAME is selected, one image can be memorized in FRAME mode. • When FIELD is selected, each one image can be memorized in FIELD A and FIELD B. One image in FIELD A One image in FIELD B • "FIELD A[B]" or "FIELD [A]B" is displayed on the lower part of the monitor screen.
PAGE 24
6. Printing procedures (Basic prints) Image memorizing with PAGE INC (Page Increment) function PAGE INC (Page Increment) : When the “automatic memory page turning” function is valid, the image memorizing is done as follows: • After selecting FIELD, the image is stored in “A” first. After that, each time the MEMORY button is pressed, the images will be memorized in the order of B, A, B....
PAGE 25
6. Printing procedures (Basic prints) 2 Continuous printing The desired number of memorized images can be printed continuously when the desired number is set before printing. The number of prints can be changed during printing. The continuous printing also can be cancelled by setting the number of prints to 1 during printing. Setting the number of prints Press the PRINT Q'TY buttons • Press , , to set the number of prints. button to increase and button to decrease the number.
PAGE 26
7. Setting the functions Setting each function on the menu display. There are 2 functions menus. 1 " MAIN MENU " Sub menu 2 " MEMORY SW MENU " Sub menu 1 MAIN MENU is used to open the sub menu. Setting the following with the sub menu. When selecting "SAVE", the setting can be stored. Monitor display 1.COLOR ADJ ....... Adjust color of printing image 2.SIGNAL SET .......
PAGE 27
7. Setting the functions Operation Monitor displaly 3.ADDITIONAL STOROBE : OFF/1/15 sec MULTI : OFF/ON MODE : SAME/DIFF/PHOTO IMAGES : 2/4/16 SEPARATE : OFF/ON CHANGE The menu is selected by pressing the shift buttons . : OK/CANCEL Changing a value, selecting mode, switching ON or OFF is switched by pressing . p31 CHANGE: OK SET p33 CHANGE: OK 1.COLOR ADJ BRT : 0 CONT : 0 COLOR : 0 TINT : 0 W.B-RED : 0 W.B-BLUE : 0 CENTER : OFF/ON ANALOG ADJ : PUSH[ ]] CHANGE: OK/CANCEL 2.
PAGE 28
7. Setting the functions p shows the reference page. p32 ANALOG BRT CONT COLOR CENTER ADJ : 0 : 6 : 12 : OFF/ON p44 POWER CHANGE: OK/CANCEL SET MEMORY CHANGE: OK SET 1 . KEY SETTING KEY LOCK : OFF MEM&PRINT : OFF MEM&STOP : OFF MEM&MON : OFF PRINT&CLR : OFF CLEAR KEY : ONE ON ON ON ON ON ALL CHANGE: OK/CANCEL When pressing the power button while pressing the MEMORY button, the following menu is indicated. Displayed when VIDEO signal is inputted p45 CHANGE: OK SET p43 MEMORY SW MENU 1.
PAGE 29
7. Setting the functions Displaying menu screen • All functions are operated with the remote control. 1 Main menu – sub menu display MENU • Press the MENU 2 MEMORY SW • • button to display Main menu. MENU – sub menu display Press the POWER button while pressing MEMORY button to display MEMORY SW menu. Make sure to turn the POWER OFF before the above operation. Displaying the sub menu • Select the sub menu for each function setting to display from MEMORY SW MENU or MAIN MENU.
PAGE 30
7. Setting the functions 3 Press the SET • " CHANGE : OK/CANCEL " is selected. • Select "OK" to close the menu. Select "CANCEL" to cancel the setting again by the RIGHT 4 Press the SET • The function is set and the Main menu SET button. or LEFT shift button. SET button. display or Memory SW menu is shown. 5 SET button. Press the SET • In the Main menu, "SAVE : 1/2/3" is selected. Store the setting of function on the sub menu 1-6 to program 1.2 and 3. ( Refer to "SAVE"on the next page.
PAGE 31
7. Setting the functions (Main menu) Function 1 MAIN MENU Open the sub-menu from Memory menu. e.g. Monitor display 1. COLOR ADJ BRT Items and setting displayed are shown below. 1.COLOR ADJ ....... Adjust color of printing image 2.SIGNAL SET ....... Selecting the input signal, reverse of odd and even field lines, automatic frequency control, automatic gain control, separating composite video signal, etc. 3.ADDITIONAL .......
PAGE 32
7. Setting the functions (Main menu) 1 COLOR ADJ Adjusting the color of the image • With this menu, the color of the source image and memorized image can be adjusted. COLOR ADJUST • This menu is also displayed by pressing COLOR ADJUST button. BRT (Bright ) Function CONT (Contrast ) Function Adjust the brightness of printing image.
PAGE 33
7. Setting the functions (Main menu) ANALOG ADJ The adjustment image of analog input signal display • This menu is used to adjust the image of analog input signal display before storing in the memory. • This menu is opened when pressing RIGHT shift button on "ANALOG ADJ : PUSH [ ] ". BRT (Bright ) Function CONT (Contrast ) Function Adjust the brightness of printing image. Adjust the contrast of printing image.
PAGE 34
7. Setting the functions (Main menu) 2 SIGNAL SET Signal selecting menu INPUT Function Select the signal from inputting signal terminal on the rear panel. VIDEO .......... Signal from VIDEO input terminal S -VIDEO ..... Signal from S-VIDEO input terminal FIELD Function The odd/even field lines will be reversed depending on the input interlaced signal. Printing image is not clear so that the odd and even field lines may be reversed depending on the input interlaced signal.
PAGE 35
7. Setting the functions (Main menu) 3 ADDITIONAL STROBE Function Special print setting This function is used to repeat storing the image in the memory according to the selected time interval. When MULTI is set to "ON", the image is stored in order of image number . When MULTI is set to "OFF", every one image is stored in the memory. • The image is stored in the memory every time as shown below. 1/3 sec 1 sec 2 sec 5sec 10 sec 30 sec ...............................................
PAGE 36
7. Setting the functions (Main menu) SEPARATE Function Switching the white frame Separate the each image in multi-image print with white frame ON ............... White frame print OFF ............... Normal print • When "MULTI" is set to "ON", this function is displayed. 4 PRINT MODE Function Print setting 1 Selecting the paper size Selecting the paper size depending on the installed the ink sheet. L ................... L-size ink-sheet ( model: PK700L) S ...................
PAGE 37
7. Setting the functions (Main menu) COMMENT Function Selecting the comment Selecting the comment on printing from 5 types. OFF ...... Comment is not printed. ON ...... Print the made comment. • The following is displayed only when COMMENT is set to ON. SELECT COM ..... Printing the made comment ADJ ...... Printing the set value in the " 1.COLOR ADJ " menu. DATA ... Printing the total number of prints, filter or image size etc.. • When selecting "ADJ", the following information is printed.
PAGE 38
7. Setting the functions (Main menu) 5 COMMENT Function Making a comment Making a comment on print Refer to pages 39-42 for details.
PAGE 39
7. Setting the functions (Main menu) USER SIZE ADJ Setting the image size The printing area can be changed and stored in memory as a user setting. When selecting " USER ADJ " on the "6.SYSTEM "menu . Press the RIGHT shift button, then, USER SIZE ADJ menu is displayed. SET When pressing the SET button after setting, " CHANGE : OK/CANCEL " is selected. SET • When selecting " OK " and pressing the SET button, SYSTEM menu is displayed. COPY Function Copy "SIZE" in the " 6.SYSTEM" menu.
PAGE 40
7. Setting the functions (Making a comment) Making a comment Select the making a comment menu "COMMENT". This functions are operated with the remote control using the menus displayed on the monitor screen. Explanation 5.COMMENT [POSITION] 2 A) {SELECT} 20 1 2 3 4 5 6 7 8 9 + - /= ( ) < > [ ] { } !\#$%&?@"',.:;^ ± CHANGE: OK/CANCEL B) C) • Listed below are the three comment displays. A ) Comment display block................. B ) Character block...............................
PAGE 41
7. Setting the functions (Making a comment) Comment making procedure 1 Press the RIGHT or LEFT shift button to select the position where a letter is inputted. 5.COMMENT [POSITION] • Select position is indicated in red. 2 {SELECT} 20123456789+- /= ( ) < > [ ] { } !\#$%&?@"',.:;^ ± CHANGE: OK/CANCEL 2 Press the UP or DOWN Comment making display shift button to select the inputting letter. 5.COMMENT [POSITION] 4 • The selected letter is indicated in red in upper comment block.
PAGE 42
7. Setting the functions (Making a comment) Changing character type 1 MENU Press the MENU button. 5.COMMENT [DEL ]INS 456789 • Comment editing display is shown. 2 {PAGE} 0123456789+- /= ( ) < > [ ] { } !\#$%&?@"',.:;^ ± CHANGE: OK/CANCEL 2 Press the UP or DOWN shift button to select the character type. 5.COMMENT [DEL ]INS 456789 • The characters in the character block change.
PAGE 43
7. Setting the functions (Making a comment) Close the comment menu 1 SET Press the SET button to select " CHANGE : OK/CANCEL" . • " CHANGE : OK/CANCEL " is displayed in red. 5.COMMENT [POSITION] 456789 2 {SELECT} 0123456789+- /= ( ) < > [ ] { } !\#$%&?@"',.:;^ ± CHANGE: OK/CANCEL 2 Press the shift button to select "OK" . • In case of changing a comment , select the "CANCEL". SET When pressing the SET button after selecting "CANCEL", the comment previously memorized is shown. 3 SET button.
PAGE 44
7. Setting the functions (Memory SW menu) SETTING FUNCTIONS MEMORY SW MENU 2 When pressing the POWER button while pressing the MEMORY button on the front panel with the POWER turned off the MEMORY SW MENU is displayed. (e.g.) MEMORY SW MENU 1. KEY SET KEY LOCK Item and setting are as shown below. 1. KEY SET ................... The function of button is invalid, setting the function of memory button 2. REMOTE SET ...........
PAGE 45
7. Setting the functions (Memory SW menu) 1 KEY SETTING Setting the buttons' function KEY LOCK Function The function on the remote control buttons and all of the buttons of the unit except POWER button are not available. ON ................ The function on the remote control buttons except MEMORY, PRINT, MONITOR are not available. OFF ................ All of the buttons on the remote control are available. • To set KEY LOCK to OFF, turn off the power and on, then set KEY LOCK again.
PAGE 46
7. Setting the functions (Memory SW menu) 2 REMOTE SETTING Remote terminal setting display CONNECT Setting the No. 2 pin function of the remote terminal 2 on the rear panel. NORMAL .............. No. 2 pin functions as "MEMORY". Function PRE-CUT ............... No. 2 pin functions as "PHOTO". "PRE-CUT" is a menu for printing on the pre-cut sheet. By setting the PHOTO signal level of the remote terminal 2, each setting for printing on pre-cut sheet can be done automatically. Refer to pages 64-66.
PAGE 47
7. Setting the functions (Memory SW menu) External remote terminal 1 External remote terminal 2 1 terminal 2. • The individual definition is available in BUSY 1 and BUSY 2. 2 BUSY 1 BUSY 1 • The signal defined in BUSY 1 is output from Remote terminal 1. • The two signals defined in BUSY 1 and 2 are output from Remote BUSY 2 • Make the necessary signal definition. • The active level signal in BUSY 2 will also be output at buzzing when you set "REMAINING" function ( refer to next page).
PAGE 48
7. Setting the functions (Memory SW menu) V POSITION Function Adjusting the vertical position of printing image. Setting area - 28 to +28 ( Change each 2 lines) When 2-image printing ( selected "2" in IMAGES) on L size print paper, the top and bottom of the image may not be fully printed depending on memory size. It may be necessary to adjust part of the image in the UP, DOWN, RIGHT or LEFT direction.
PAGE 49
8. Printing procedures (Special prints) The following printing is available. 1 MULTI prints SAME or DIFF ............................ Pages 50 - 53 2, 4, or 16 images can be printed on a sheet. 2-image S-size paper L-size paper 4-image S-size paper L-size paper 16-image S-size paper L-size paper 2 PHOTO prints PHOTO .................................... Pages 54 - 57 Photo prints can be made on two types of the sheet in the market and a card size sheet (suited size to stick on a business card.
PAGE 50
8. Printing procedures (Special prints) Storing multi-image in memory The multi-image can be stored in memory as follows. SAME (The same two images are printed on a sheet.) 2-image mode SAME DIFF FIELD A • 1 image is stored in FIELD A. • • 1 image is stored in FIELD B. 1 image is stored in FRAME. • 2-image print consists of the memorized one image. FIELD The images of FIELD A and FIELD B are printed on a sheet. FIELD B FRAME can not be selected. The image of FIELD mode is displayed.
PAGE 51
8. Printing procedures (Special prints) 1 MULTI PRINTS 2, 4 or 16 images can be printed on a sheet. • The following prints are available. S size prints One image printing 16 A A A A A A A A A A A A A A A A A A A A A A A 4 A A 2 L size prints A Setting of the No. of images A A A A A A A A A A A A A A A A A A A A example : "W" is selected on "SIZE" in 6.SYSTEM. "OFF" is selected on "SEPARATE" in 3.ADDITIONAL. "A" shows the direction of images.
PAGE 52
8. Printing procedures (Special prints) 3 Press the DOWN or UP shift button to select "MULTI : OFF/ON ". Then, press the RIGHT shift button to select "ON". • "MODE : SAME/DIFF/PHOTO " is displayed on the menu screen. • "IMAGES : 2/ 4/ 16 " is displayed on the lower line. 4 Press the DOWN shift button to select " MODE : SAME/DIFF/PHOTO ". Then, press the RIGHT shift button to select SAME " or " DIFF ". • When " SAME " is selected, a multi-image (2, 4 or 16 images) of the same image can be printed.
PAGE 53
8. Printing procedures (Special prints) Storing images in memory 1 Press the DISPLAY button to display the set conditions. 2 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. 3 Press the MONITOR button and select the source image ("LIVE" is displayed on the monitor.) to display the image to be stored in memory. 4 Press the MEMORY button to store the image to be printed. Storing 2-multi-image in memory "IMAGES : 2" • When "MODE" is set to "SAME" FIELD ......
PAGE 54
8. Printing procedures (Special prints) Storing an image in any position When "MODE" is set to "DIFF" and "IMAGES" to 4 or 16 1 Press the DISPLAY button to display the set conditions. 2 Press the MONITOR button. Select source image ("LIVE" is displayed on the monitor.) to display the image to be stored in memory. 3 Press the DISPLAY button to display the set conditions. • The memory page number where the image can be stored is indicated.
PAGE 55
8. Printing procedures (Special prints) 2 PHOTO PRINTS PHOTO print is a function to print the images on the photo size (3x4cm, 3x3.5cm, 5x5cm) and card size. • CARD size print is suited to stick on a business card. • The following prints are available. PRG. 1 Q'ty 1 A A A VIDEO FRAME MEMORY PRG. 1 A A 3 4 A A Q'ty 1 AA AA 5 L size prints Separate OFF Separate ON Separate OFF A A A A 5 Separate ON A A A A P H O T O S size prints Memorized image on the monitor A A Setting the No.
PAGE 56
8. Printing procedures (Special prints) Selecting the size 1 Press the DOWN shift button to select " IMAGES : CARD / 3*4/ 5*5 / 3*3.5 " menu. 2 Press the RIGHT shift button to select " CARD " , " 3*4 " , " 5*5 " or " 3*3.5 ". Displaying the image from input signal (source image) or the memorized image SET 1 Press the SET button. • " CHANGE : OK/CANCEL " is selected. SET • When changing the PHOTO print setting, select "CANCEL" and press the SET button. SET 2 Press the SET button.
PAGE 57
8. Printing procedures (Special prints) Printing the images 1 Press the MONITOR button to display the memorized image. ("MEMORY" is displayed on the monitor.) • A blue frame is indicated on the displayed image. • The image within the blue frame is photo-printed. PRG. 1 Q'ty 1 The blue frame moves with the SHIFT buttons. A VIDEO FRAME example : When "3x4" or "CARD is selected. MEMORY In FIELD mode, press the MEMORY PAGE button to select the memory page to print.
PAGE 58
8. Printing procedures (Special prints) Refer to pages 50-53 (16-Multi-image) and pages 54-57 (PHOTO PRINTS) for storing image in memory. The menu only for pre-cut PHOTO size printing can be used. • Set the function of No. 2 pin of the remote terminal 2 on the rear panel to "HIGH" level. Refer to page 65. (When the remote terminal 2 is not used, "HIGH" level is set.) • Set "CONNECT" in "2. REMOTE SETTING" in MEMORY SW MENU to "PRE-CUT". Refer to page 45.
PAGE 59
8. Printing procedures (Special prints) OPERATION Setting the multi-print and photo-print menus Setting multi-print and photo-print functions 1 Press the MENU button. Then, press the UP or DOWN shift button to select " 3. ADDITIONAL PUSH [ 2 Press the RIGHT shift button to select "3. ADDITIONAL". 3 Press the DOWN shift button to select " MULTI : OFF/ON". Then press the RIGHT ] ". shift button to select "ON " . • " MODE : SAME/DIFF/PHOTO " is displayed on the menu screen.
PAGE 60
8. Printing procedures (Special prints) SET 5 Press the SET button. • The source image (image from the input signal) or memorized image is displayed. Storing images in memory / Printing the images 1 Store the images to be printed in memory. • Refer to 1 MULTI PRINT or 2 PHOTO PRINT for storing images in memory. 2 Press the PRINT button. • The set SEPARATE images are printed. Note : • The distance between images in multi-print is different between on the monitor and the printed image.
PAGE 61
8. Printing procedures (Special prints) Setting 1-image/multi-image memory When memorizing 1 image in STROBE mode This setting is used to memorize 1 image in FRAME, FIELD A or FIELD B. 1 Set the mode to 1-image. Select "OFF" in "MULTI : OFF" in "3. ADDITIONAL". 2 Set the page increment function to ON. Set the "PAGE INC" to ON in "6. SYSTEM". (The initial setting is "ON".) page [B] page [A]....
PAGE 62
8. Printing procedures (Special prints) SET 3 Press the SET button. • "SAVE 1/2/3" is selected. • This menu is used to store the setting in any one of 3 programs (1, 2 or 3). 4 Press the RIGHT or LEFT shift button to select the program number 1, 2 or 3 to store the setting. • The setting will be overlaid. When keeping the stored program, do not select the program No. in which the setting is stored. SET 5 Press the SET button.
PAGE 63
8. Printing procedures (Special prints) Setting the automatic interval printing By combining STROBE printing and MEMORY printing, automatic interval printing is available. This is the function where the images are stored in memory at the set interval and printed repeatedly. ... ... ... Automatic interval prints (1 image ) This is the function to store the image in memory page FRAME, FIELD A or FIELD B in order at set interval and print repeatedly. 1 Set 1 image mode. Set "MULTI : OFF/ON" to "OFF" in "3.
PAGE 64
8. Printing procedures (Special prints) Displaying the source image (image from the input signal) or the memorized image SET 1 Press the SET button. • " CHANGE : OK/CANCEL " is selected. SET • When changing the setting, select "CANCEL" and press the SET button. SET 2 Press the SET button. • The MAIN MENU is displayed. SET 3 Press the SET button. • "SAVE 1/2/3" is selected. • This menu is used to store the setting in any one of 3 programs (1, 2 or 3).
PAGE 65
8. Printing procedures (Special prints) External remote 1 or 2 terminals on the rear panel The images can be stored in memory and printed by sending the remote signal through the external remote terminal on the rear panel. When "MEM & PRINT" function is set to "ON", the images can be printed after storing. • Switching High/Low of BUSY signal and defining BUSY signal can be done in "2.REMOTE SET" in MEMORY SW MENU. • Make out the necessary circuit to use this function by referring to the following.
PAGE 66
8. Printing procedures (Special prints) • 2 1 External REMOTE 2 terminal 4 Make out the necessary circuit to use this function by referring to the following. External remote terminal Signal allocation Connector MINI DIN8PIN Pin No. Function Transmission/ Destination 1 2 Ground MEMORY --VCP 5 3 6 7 8 Pin No. Description Earth Memory: When the signal becomes "LOW" from "HIGH", the image is stored in memory. (When the signal has been "LOW" for 60msec. or more, the image is stored in memory.
PAGE 67
8. Printing procedures (Special prints) Circuit inside the VCP VCP User side DC5V To VCP 10KΩ 1KΩ CMOS 100Ω 2 MEMORY / PHOTO mode input DC5V 10KΩ DTC124EK From VCP 100Ω 22KΩ 3 BUSY2 22KΩ DC5V 10KΩ DTC124EK From VCP 100Ω 22KΩ 4 BUSY1 22KΩ DC5V To VCP 10KΩ 1KΩ CMOS 100Ω To VCP 1K 5 PRINT 6 REMOTE Pin No. 6 REMOTE terminal By sending the following remote control codes from Pin No. 6, the same functions as the wired remote control (accessory) can be controlled.
PAGE 68
9. Troubleshooting Error messages and countermeasures If for some reason printing is not possible or error occurs during printing, the error message will be displayed on the monitor screen. In this case, follow the procedure described below. Causes Error messages DOOR OPEN PAPER EMPTY Countermeasures The printing unit is not inserted correctly. Insert the printing unit until it is locked in the unit. Paper is not set. Set the print paper correctly. Paper is not set correctly.
PAGE 69
9. Troubleshooting Other messages MECHA INITIALIZE REQUEST Indicated when the power is turned on after turning off during printing. Press the MEMORY button for more than on second while pressing the MONITOR button. *Note : 3 MECHA INITIALIZE Indicated during initializing. PRINT STOP In the case of pressing the STOP button on the remote control during printing, this unit is initialized. This message is indicated during initializing. *Note : 3 This is an operation for initialization.
PAGE 70
9. Troubleshooting Before calling for service Symptom No power Check and Remedy Is the power cord plug disconnected form the outlet? Connect the power cord plug to the outlet firmly. After turning the power off, wait for approx. 2 minutes. Then turn the power ON. No image appears on the monitor. Are the video signal and sync. signal inputted to this unit? Check the connection. Refer to pages 9-10.
PAGE 71
9. Troubleshooting Symptom The stored image in the memory cannot be enlarged to fill the maximum print area. Check and Remedy Is the SMALL size ink-sheet installed when selecting “S” in “MODE : S/L”? Or is the LARGE size ink-sheet installed when selecting “L” in “MODE : S/L”? Check the current setting. Refer to page 35. Is the paper size set to “N” in the size setting in SYSTEM menu? Set the size to “M” or “W”. Refer to page 37. Is the S size image printed on the L size paper? Check the current setting.
PAGE 72
10. Cleaning Cleaning thermal head When the thermal head is dirty with dust, etc., white spots or stripes may appear on the print. In this case, clean the thermal head in the following procedure. 1 Open the door. 2 Remove the ink-cassette and print paper. 2 1 3 Wipe off stains on the bottom of the thermal head 2 or 3 times with a soft cloth (cleaning cloth for video head is on the market) moistened with alcohol.
PAGE 73
11. Options The following products are sold separately. Ink sheet Product name Ink sheet size No. of prints Usage PK700S S size 200 For 3 color use PK700L L size 125 For 3 color use Print paper Product name CK700 Ink sheet size No. of prints Usage For S and L size S size : Approx.200 For 3 color use L size : Approx.125 Ink sheet / print paper Product name CK700L4P Ink sheet size No. of prints L size 75 Usage For 3 color use (Surfacecoatd paper) CK710SPC S size Approx.
PAGE 74
12. Specifications Class Colour Video Copy Processor Model CP710E Printing method Sublimation Dye Thermal 3 color faces progressive printing ( yellow, magenta and cyan) Print quality Printing time Dot resolution max.1200 x 600 pixels Number of grades 256 for each color Approx.39 sec./ sheet (L size one image print) Approx.22 sec.
PAGE 75
Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (1) 707 276100 FAX (1) 707 278755 German Branch Gothaer Strasse 8, Postfach 1548, 40880 Ratingen 1, Germany Phone (2102) 4860 FAX (2102) 486-732 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.