DIGITAL COLOR PRINTER MODEL CP9000DW OPERATION MANUAL POWER DOOR OPEN ALARM PAPER/INK RIBBON DATA READY CANCEL COOLING FEED&CUT THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. This digital color printer complies with the requirements and other relevant provisions of the EC Directive 89/336/EEC, 73/23/EEC, 93/68/EEC and 1999/ 5/EC.
INFORMATION This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Use the included AC power cord so as not to interfere with radio and television reception. If you use other cables, it may cause interference with radio and television reception.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CONTENTS PRECAUTIONS CONTENTS 1 2-4 5 6 7-8 FEATURES Contents ................................................................................................ Safety precautions ................................................................................ Special features .................................................................................... Unpacking ............................................................................................. Features and functions ....................
SAFETY PRECAUTIONS In the interest of safety, please observe the following precautions: PRECAUTIONS POWER REQUIREMENT This Digital Color Printer is designed to operate on 120V AC 50/60Hz in U.S.A. and Canada, 220V-240V AC 50/60Hz in Europe. Never connect to any outlet or power supply having a different voltage or frequency. WARNING : THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE. FEATURES PROTECTIVE MEASURES IF ABNORMALITIES ARISE, .....
SAFETY PRECAUTIONS REMOVE THE PAPER STRIP BIN WHEN OPENING OR CLOSING THE DOOR PRECAUTIONS When you open or close the door with the paper strip bin installed, the bin may be removed and fall. This may cause injury or damge. INSTALLATION LOCATIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on the rear and both sides of this unit. Place the unit on a hard and level surface and locate at least 10cm (4 inches) from walls to insure proper ventilation.
SAFETY PRECAUTIONS • Do not pull out nor touch the print paper until printing is completed. It may degrade the print quality or cause an error. • Dust or other foreign matter adhering to the print paper or the ink cassette, or deformation resulting from exposure to extremely low or high temperatures could cause loss of color, uneven color or lines, or wrinkles in the print images.
SPECIAL FEATURES PRECAUTIONS SPECIAL FEATURES TWO PRINT SIZES ARE AVAILABLE DEPENDING ON THE PURPOSE Two printing sizes, 9x13 (3.5x5”) (max.89 x 127 mm) and 10x15 (4x6”) (max.102 x 152 mm), are selectable. HIGH SPEED PRINTING Normal printing speed is approx. 20 seconds (in 9x13 (3.5x5”) Fine mode print). Use of roll paper shortens the time for installing and removing. FEATURES LARGE CAPACITY PRINTING Maximum of 680 prints per roll for 9x13 (3.5x5”) is offered.
UNPACKING UNPACKING PRECAUTIONS Take the printer out of the box by the following procedures. Make sure to check the accessories. 1 Open the top of the box. FEATURES 2 Remove the accessories together with upper cushions. CONNECTIONS PREPARATION 3 Hold the handles of the cardboard and pull it up carefully to take the printer together with the lower cushions out of the box. Make sure to pull the cardboard straight up. NOTE This printer is about 17 kg in weight. Handle it with care.
FEATURES & FUNCTIONS 6 9 8 7 10 PRECAUTIONS FRONT PANEL 11 PAPER STRIP BIN Hook the paper strip bin by its latches. 4 POWER ALARM PAPER/INK RIBBON DATA DOOR OPEN READY CANCEL COOLING 12 FEED&CUT A FEATURES 5 B 13 3 2 1 2 To attach: A -> B To remove: B -> A 1 POWER BUTTON Use to switch the power ON and OFF. Press to turn on power. Press again to turn off power. 2 PAPER STRIP BIN 9DATA INDICATOR This indicator blinks during data transfer. It illuminates during printing.
FEATURES & FUNCTIONS PRECAUTIONS SIDE AND REAR PANEL 1 FEATURES 4 3 2 3 CONNECTIONS PREPARATION 5 5 AC LINE 6 (LEFT SIDE) (REAR) 1 USB TERMINAL 4 DIP SWITCHES Use to connect the USB cable. Use to set various functions of this unit. See page 11. For setting, see page 10. 5 HANDLE FOR TRANSPORTING When transporting this unit, hold this handle and the lower front part of this unit. Use to set the SCSI ID number of the connected device. See page 9.
CONNECTIONS PRECAUTIONS CONNECTION WITH SCSI DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) 1 Press the POWER button to turn on the power. FEATURES 2 Press the DOOR OPEN button to open the door. 3 Set the input select switch inside this unit to SCSI. Push the center of the door to close. 4 Press the POWER button to turn off the power. CONNECTIONS PREPARATION 5 Connect the unit and the personal computer with a SCSI cable.
CONNECTIONS PRECAUTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) 1 Press the POWER button to turn on the power. 2 Press the DOOR OPEN button to open the door. FEATURES 3 Set the input select switch inside this unit to USB. Push the center of the door to close. CONNECTIONS PREPARATION Input select switch 4 Press the POWER button to turn off the power. 5 Connect the unit and the personal computer with a USB cable.
CONNECTIONS 2 SETTING DIP SWITCHES OFF ON FEATURES 12345678 All the switches are set to OFF at the time of shipment from the factory. Turn off the power before changing the DIP switch settings. PRECAUTIONS SETTING OF DIP SWITCHES CONNECTIONS PREPARATION Switch No. Setting Function 1 OFF Auto feed & cut mode When the door is closed after the print paper or a ink cassette is installed with this unit powered on, this unit automatically carries out paper feed & cut operation.
BEFORE OPERATION Before printing, PRECAUTIONS 1 Install the print paper to this unit. (See below.) 2 Install the ink ribbon to this unit. (page 14-15) INSTALLATION OF PRINT PAPER FEATURES latches Spacers 2 The spacers are attached to the paper flanges. For the necessity of the spacers, see the Quick Setup Guide. Remove the cushions put between the paper flange and spacer when CONNECTIONS PREPARATION use them. How to attach and remove the spacers 1. Turn the spacer until the latches are unlocked. 2.
BEFORE OPERATION 2 Press the POWER button to turn on the power. PRECAUTIONS 3 Press the DOOR OPEN button to open the door. FEATURES Take the ink cassette in the printer out. CONNECTIONS PREPARATION 4 Install the print paper into the unit. Make sure to install the print paper firmly. NOTE Install the print paper into the unit slowly. If it is dropped along the ditches, the unit or accessories may be damaged.
BEFORE OPERATION PRECAUTIONS INSTALLATION OF INK RIBBON 2 INSTALLING THE INK RIBBON After installing the print paper, install the ink cassette into this unit. Before installing the ink cassette into this unit, load the ink ribbon in the ink cassette. NOTE Place the ink cassette on a flat surface, when loading the ink ribbon. Select a place that is free of dust when loading the ink ribbon. Dust or dirt settling on • the ink ribbon results in poor print quality.
BEFORE OPERATION 2 Push the ink cassette toward the back of the unit. PRECAUTIONS Hold the handle of the ink cassette and push it straight toward the back of the unit. Then raise it until you hear a click to secure it in the ink cassette holder. NOTE If the ink ribbon is used up, repeat the steps 1 to 2 to replace the print paper and the ink ribbon. FEATURES CONNECTIONS PREPARATION 3 Push the center of the door to close. The print paper setting is initialized two minutes after you close the door.
BEFORE OPERATION PRECAUTIONS HANDLING OF PAPER / INK RIBBON SET 2 BEFORE PRINTING • Fingerprints or dust on the paper’s printing surface may degrade the print quality and cause paper jams. When the manual feed & cut mode has been selected, repeat the FEATURES FEED & CUT procedure three times after replacing the print paper. When the print paper with the post card printing on its reverse side is installed, repeat five times.
BEFORE OPERATION PRECAUTIONS INSTALLATION OF PRINTER DRIVER 2 The printer driver is required to print the data from the personal computer connected with this unit. The printer driver for Windows® is supplied with this unit.
ERROR MESSAGES & COUNTERMEASURES 2 If, for some reason, printing is not possible or an error occurs during printing, the indicators on the front panel will illuminate or blink. In this case, follow the procedure described below. In case of an error during printing, unless you turn off the unit, the unit resumes printing automatically when the error is corrected.
ERROR MESSAGES & COUNTERMEASURES PRECAUTIONS OVERCOMING PAPER JAMS 1 Press the DOOR OPEN button to open the door. Make sure that the power is turned on before opening the door. If the door does not open, turn off the power and turn it on again. Then press the DOOR OPEN button again. FEATURES 2 Remove the ink cassette. Push down the ink cassette as shown by the arrow 1 and pull it out. CONNECTIONS PREPARATION 2 1 3 Take out the print paper. When taking the print paper out, pull it up toward you.
ERROR MESSAGES & COUNTERMEASURES PRECAUTIONS BEFORE CALLING FOR SERVICE For the following symptoms, check the unit again before calling for service. Symptom Check & Remedy The power is not turned on. Is the power cord plug disconnected from the outlet? FEATURES → Connect the power cord plug to the outlet firmly. → The protective circuit may be working. Turn off the power and wait for about two minutes. Then turn on the power again.
CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer’s life. A small amount of alcohol PRECAUTIONS Preparations Alcohol (isopropyl alcohol) Tissue paper (Fold in half about four times, and use the folded side to clean.) Cleaning part Other : Cleaner pen (option)*, Cleaning ribbon (option)* * Please ask the dealer about options. How to fold tissue paper 1 Press the POWER button to turn on the power.
SPECIFICATIONS Class Digital Color Printer Model Printing method CP9000DW Sublimation Dye Thermal Transfer line print Print’s resolution 3-color faces progressive printing (yellow, magenta, and cyan) and surface lamination 346 x 346 DPI (Fine mode) 346 x 692 DPI (Super Fine mode) (DPI : Dots per inch) 9x13 (3.5x5”) 10x15 (4x6”) 1812 x 1240 pixels (Fine mode) 2152 x 1416 pixels (Fine mode) Print size 9x13 (3.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road, Irvine, CA 92618, U.S.A. Phone 949-465-6000 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (0) 1707 276100 FAX (0) 1707 278755 German Branch Gothaer Strasse 8, 40880 Ratingen ; Postfach 1548, 40835 Ratingen ; Germany Phone 02102/ 486-9250 FAX 02102/ 486-7320 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.