MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL NFJ9905SKHUW USER’S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor.
The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. ANMERKUNG: Dieser Monitor erfüllt die Anforderungen der deutschen Ergonomie-Norm ZH1/ 618/10.80 bei Verwendung der beiden folgenden Timing: Auflösung Videoeingang 1280x1024 Analog RGB, 0.7Vs-s fH(kHz) fv(Hz) Interlace/Non-Interlace 91.1 85.
ENGLISH RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ENGLISH Congraturations! You have just purchased a TCO ‘95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentallyadapted electronic products.
ENGLISH In and after the middle of this page, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development Unit S-114 94 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development @tco.se Current information regarding TCO’95 approved and labelled products may also be obtained via the Internet, using the address: http//www.tco-info.
ENGLISH User’s Guide CONTENTS 1. INTRODUCTION .................................................................................................. 1.1 Features ..................................................................................................... 1.2 Internal Preset Memory Capability ............................................................. 1.3 Power Management Function .................................................................... 1.4 DDC ...........................................
ENGLISH 1 INTRODUCTION Congratulations on your purchase of the high resolution color monitor. We designed this monitor to provide you with years of reliable trouble-free operation. This guide tells you how to connect, adjust and care for your monitor. This guide also provides technical specifications and instructions for troubleshooting any basic problems you may experience with your monitor. 1.1 Features The Diamond monitor is a 50cm/19"(46cm/18.
Internal Preset Memory Capability To minimize adjustment needs, the factory has preset popular display standards into the monitor, as shown in Table 1. If any of these display standards are detected, the picture size and position are automatically adjusted. All of the factory presets may be overwritten by adjusting the user controls. The monitor is capable of automatically storing up to six additional display standards.
ENGLISH 1.4 DDC The monitor includes the DDCTM1 and DDCTM2B feature. DDC (Display Data Channel) is a communication channel over which the monitor automatically informs the host system about its capabilities (e.g. each supported resolution with its corresponding timing). DDC is routed through previously unused pins of the 15-pin VGA connector. The system will perform “Plug and Play” feature if both, monitor and host, implement the DDC protocol. 1.
Unpacking After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you ship or transport the monitor. Complete and mail in warranty cards. 1 2 3 5 4 6 NN OO 1 2 3 4 5 6 7 9 8 10 11 Figure 1. 1.8 1. Color Monitor 2. AC Power Cord 3. Signal Cable SC-B102 4. USB Upstream Cable 5. Macintosh Adapter AD-A205 6. Floppy Disk 7. Ferrite Core 8. Software Agreement 9. User's Guide 10. Warranty-Card 11.
ENGLISH 1.9 Quick Operation Chart To summarize the steps in connecting your computer with the color monitor and setting the necessary controls and switches, refer to the chart below. Connect the color monitor and computer with the necessary cords and cables. See 3. INSTALLATION AND CONNECTION Turn on the computer. Turn on the color monitor. Set the controls. See 4. OSD(On Screen Display) FUNCTIONS If a problem appears. OK OK See 5. TROUBLESHOOTING If the problem persists.
2 PART NAME 1. POWER SWITCH 2. POWER-ON INDICATOR 7. DOWNSTREAM PORT 3. INPUT CONNECTOR SELECT BUTTON BNC / D-SUB SCROLL 6. FUNCTION ADJUST BUTTONS ENTER 4. SCROLL BUTTON 5. ENTER BUTTON Figure 3 2.2 Function 1. POWER SWITCH: A push-on / push-off switch for AC power. 2. POWER-ON INDICATOR: This indicator illuminates at green when AC power is on, and illuminates at amber when the monitor is in the power management modes. 3.
ENGLISH REAR D-SUB BNC R AC POWER CONNECTOR 8. UPSTREAM PORT G B COMP. HD VD SIGNAL INPUT CONNECTOR (DB9-15P) A D-SUB B BNC 1 R G B COMP. HD VD 2 9. DOWNSTREAM PORT SIGNAL INPUT CONNECTOR (BNC) Figure 4 8. UPSTREAM PORT: To connect to USB equipped computer(s). 9. DOWNSTREAM PORT: To connect to USB equipped peripherals, e.g, USB camera, keyboard, printer, etc.
3 INSTALLATION AND CONNECTION 3.1 AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor’s auto-sensing power supply can automatically detect 100-120V AC or 220-240V AC and 50 or 60Hz. 3.2 Signal Cable Connection The attached video signal cable provides a DB9-15P connector for the VGA compatible analog RGB outputs on your computer.
ENGLISH 3.2.2 Connecting to An Apple Macintosh Computer Figure 6 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple Macintosh. 1. 2. 3. 4. 5. 6. 7. Power off, both the monitor and the computer. Set the DIP switches of Macintosh Adapter according to the setting chart. (See 7.3 Macintosh Adapter AD-A205 settings) Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the CPU or on the video board.
(1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN): Connect the R, G and B video signals to the BNC receptacles on the back of the monitor. D-SUB BNC R B G COMP. HD VD (2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively. D-SUB BNC R B G COMP.
ENGLISH 3.3 USB System Basic Application FRONT BACK D-SUB BNC R G B COMP. HD VD Upstream Ports Downstream Port A D-SUB B 1 2 BNC R G B COMP. HD VD Downstream Ports Scanner Keyboard Camera Computer NOTE The computer is required to have Windows 98 installed and USB functions. When connecting one computer, either Upstream port A or B is available. The Upstream port with that the computer is connected is detected automatically.
D-SUB BNC A B R 1 G B COMP. HD VD 2 USB CONNCTOR (DOWNSTREAM) USB CABLE 1 2 FERRITE CORE HOW TO MOUNT THE FERRITE CORE Place the included ferrite core under the USB cable at approx. 1.2 in.(3 cm) from the USB plug. Then, close the plastic case until you have a clock. USB Cable USB Plug Ferrite Core Approx. 1.2 in.
ENGLISH 3.4 Installation of USB Function 1. Power on the display monitor and computer. 2. Enumerate Mitsubishi USB HUB using the following procedure. NOTE During the enumeration of Mitsubishi USB Hub, connect the keyboard and mouse equipped with USB function, to the computer and not to the downstream ports on the display monitor. After the enumeration, the keyboard and mouse can be used by connecting to the downstream ports. (1) Insert the included floppy disk in the computer.
Enumerate the Mitsubishi Monitor Function using the following procedure. (1) Insert Windows 98 CD-ROM into your computer. Then, Figure 11 will appear. Figure 11 (2) Click “Next” on Figure 11 and Figure 12 will appear. Figure 12 (3) Click “Next” on Figure 12 and Figure 13 will appear. Figure 13 - 1-19 - ENGLISH 3.
ENGLISH (4) Click “CD-ROM Drive(C)” and “(L)”, and click “Next”. Figure 14 will appear. Figure 14 (5) Click “Finish” on Figure 14 and Figure 15 will appear. Click “OK” on Figure 15 to complete Enumeration of Mitsubishi Monitor Function. You can confirm that Enumeration of Mitsubishi Monitor Function is successfull with the following method. • Open “Device Manager” tab in “System” property under “Control Panel”.
Install “USB Monitor Control Software” into computer using the following procedure. (1) Install “SETUP.EXE” after inserting the included floppy disk in computer. CAUTION Close all Windows programs before running this Setup program. (2) Click “Next” to continue with the Setup program. (3) A software license agreement appears on screen. Click “Yes”, if you accept all the terms of the software license agreement on screen.
ENGLISH You can confirm that the Setup program is successfully installed, with the following method 1 or 2 . 1 Confirm that “Mitsubishi USB Monitor Console Application” is listed in the property of “Application Add/ Remove” under “Control Panel”. Figure 19 Tab 2 Confirm that “USB Monitor” tab is added in “Display” property under “Control Panel”.
The following should be observed in order to use the USB function reliably. • • • • • • • Make sure all connections are made firmly and correctly. Make sure the operation of the devices connected to the downstream ports before changing USB Upstream ports. It may take approximately 15 seconds max. until the devices have been enumerated by the computer and start to operate after the Upstream ports are changed.
ENGLISH 4 4.1 OSD(On Screen Display) FUNCTIONS How to adjust the screen The monitor has an OSD(On Screen Display) function. The following procedure shows how to adjust the screen with using the OSD function. (1) Turn on the monitor. D-SUB SCROLL ENTER ↓ SCROLL ENTER (2) Press any button ( ) to display the OSD screen. At the time, marks are blinking. (3) Select the group icon on Main Menu by pressing .
ENGLISH (5) Fix the item icon by pressing the proceed button . marks are blinking when fixed. ENTER BNC / D-SUB (6) ENTER SCROLL Adjust by pressing BNC / D-SUB SCROLL or button. ENTER ENTER (7) To select another item, press button once again. The fixed condition will be cancelled. At the time, marks are blinking. (8) If you don't press any button for about ten seconds, the OSD screen will disappear. Or pressing both and buttons simultaneously. The OSD screen will disappear quickly.
ENGLISH 4.2 Adjustment Items Items X: Function CONTRAST BRIGHT COLOR TEMPERATURE H-SIZE H-PHASE V-SIZE V-POSITION PCC-AMP PCC-PHASE Adjusts to the desired contrast level. Adjusts to the black level of the screen Adjusts the color temperature of the screen image. Adjusts the horizontal size of the image on the screen. Adjusts the horizontal position of the image on the screen. Adjusts the vertical size of the image on the screen. Adjusts the vertical position of the image on the screen.
Item Icon Item CONTRAST BRIGHT Press the Minus Button: To decrease the contrast. Press the Plus Button: To increase the contrast. To decrease the brightness. To increase the brightness. COLOR TEMPERATURE To increase the red color level. To increase the blue color level. H-SIZE To narrow the width of the image on the screen. To expand the width of the image on the screen. H-PHASE To move the image to the left. To move the image to the right.
ENGLISH Group Icon Item Icon Item Press the Minus Button: Press the Plus Button: H-STATIC To move the red to the right To move the red to the left and the blue to the right. and the blue to the left. V-STATIC To move the red to the upper To move the red to the lower and the blue to the lower. and the blue to the upper. MOIRE CANCEL LEVEL To decrease the level of the moire-clear. To increase the level of the moire-clear. CORNER PURITY (TL) To adjust the purity condition on the top-left corner.
Item Icon Item Press the Minus Button: The USB functions of the computer connected to Upstream port ROOT-A become active. Press the Plus Button: The USB functions of the computer connected to Upstream port ROOT-B become active. USB UP-STREAM NOTE The Upstream port in active is colored by blue on the OSD screen. In case that either the Upstream port ROOT-A or ROOT-B is chosen by this function, the auto-change of the Upstream port is not available.
ENGLISH 4.3 USB Monitor Control You can do monitor screen adjustments from your computer through the USB function equipped to the monitor, with the following procedure. (1) Open “display” in “control panel” to get “display property”. Select “USB monitor” tab. (2) Click the adjustment item and adjust with the horizontal and/or vertical slide bar.
ADJUSTMENT ITEM HORIZONTAL SLIDE BAR VERTICAL SLIDE BAR Brightness Adjusts to the black level of the screen. Contrast Adjusts to the desired contrast level. Size Controls the horizontal size of the image. Controls the vertical size of the image. Position Controls the horizontal position of the image. Controls the vertical position of the image. Top Corners Adjusts the pincushioning at the top corners of the screen.
TROUBLESHOOTING Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in 6. SPECIFICATION and 7. APPENDIX. PROBLEM ITEMS TO CHECK LED Off No picture LED On (Amber) The following message appeared. ATTENTION NO SIGNAL H OFF V OFF PLEASE CHECK INPUT SIGNAL OR CONNECTION.
ITEMS TO CHECK • [Universal serial bus controller] is not listed in [Device Manager]. No operation of the USB devices ACTION • Confirm that Windows98 is installed into the computer. • [Mitsubishi USB HUB] (or [Generic USB HUB]) is • Make sure of the cable connections. not listed in [Device Manager]. • Restart the computer. • Turn off the monitor and turn on then. • Disconnect all the cables connected to theUpstream ports and re-connect then.
ENGLISH PROBLEM Black vertical lines are visible on the screen. ITEMS TO CHECK LOCATION • Thin vertical black lines on one or both sides of • the screen. This minor condition is caused by grille element overlap which can occur during shipping. We suggest slapping the cabinet sides with an open hand after the monitor is warm. – Abnormal Picture If this fails, position an open white window over the affected area of the screen and maximize the brightness and contrast controls.
6 SPECIFICATIONS 50cm/19"(46cm/18" Diagonal Viewable Image) Aperture grille In-line 90° Red, Green, Blue EBU (medium short persistence) 0.25 - 0.27mm (variable) Anti-glare, Anti-reflection and Anti-static coating Dynamic Beam Forming (DBF) 0.7 or 1.0Vp-p analog RGB Sync. on Green or separated H, V sync. or Composite sync 5BNC, DB9-15P 75Ω (video), 1kΩ(sync.) Self-powered HUB complying with Universal Serial Bus Specification Rev.1.0.
ENGLISH 7 7.1 APPENDIX Monitor Signal Input Connector (DB9-15P) PIN ASSIGNMENTS Pin No. 1 2 (Female) 5 DB9-15P 3 4 9 10 15 6 12 13 14 1 2 7 8 11 MOUNTED ON THE REAR PANEL DDC .................. DISPLAY DATA CHANNEL SDA ................... SERIAL DATA SCL ................... SERIAL CLOCK NC ..................... NO-CONNECTION 3 4 5 6 7 8 9 10 11 12 13 14 15 7.
Macintosh Adapter AD-A205 settings The AD-A205 Macintosh Adapter allows you to take an advantage of the built in video capabilities of your Macintosh computer with the monitor. (1) (2) Set the dip switches of the adapter, before connect to the computer. Set the dip switches according to the following chart. By using the following chart, you can choose a main resolution, quickly.
- 1-38 - 640 x480@60Hz 640 x480@67Hz 640 x480@72Hz 640 x480@75Hz 640 x480@85Hz 800 x600@60Hz 800 x600@72Hz 800 x600@75Hz 800 x600@85Hz 832 x624@75Hz 1024 x768@60Hz 1024 x768@70Hz 1024 x768@72Hz 1024 x768@75Hz 1024 x768@85Hz 1152 x870@75Hz 1280 x960@60Hz 1280 x960@75Hz 1280 x960@85Hz 1280 x1024@60Hz 1280 x1024@75Hz 1280 x1024@85Hz 1600 x1200@60Hz 1600 x1200@65Hz 1600 x1200@67Hz 1600 x1200@70Hz 1600 x1200@75Hz 解像度 (RESOLUTION) 1,2 IIsi IIci 1,2 3,4 IIvi IIvx ● 3,4 1,2 2,4 1,2 3,4 3,4 3,4 1,2,6
CP871C146C10 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE: MITSUBISHI DENKI BLD, MARUNOUCHI, TOKYO 100-0005 TELEX J24532 CABLE MELCO TOKYO
