User manual

EN-22
Viewing computer images (continued)
D. Projecting images
Preparation:
t 3FNPWFUIFMFOTDBQ
COMPUTER 1, 2 buttons
Main power switch
POWER indicator
LAMP 2 indicator
LAMP 1 indicator
DVI-D(HDCP)
button
ENTER button
, , ,  buttons
POWER button
(ON/STANDBY)
, , ,  buttons
COMPUTER/DVI-D button
ENTER button
ZOOM/FOCUS button
LENS SHIFT button
POWER button (ON/STANDBY)
LENS SHIFT button
ZOOM/FOCUS button
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
t *GUIFQSPKFDUPSXBTUVSOFEPGGCFGPSFUIFMBNQXBTDPPMFEEPXOTVGmDJFOUMZMBTUUJNFUIFGBONBZTUBSUSPUBUJOH
and the POWER button may not work after the main power switch is turned ON. (The LAMP indicator blinks
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected computer.
3. Press the POWER button.
t *UNBZUBLFBCPVUNJOVUFTGPSUIFMBNQUPMJHIUVQ
t 5IFMBNQGBJMTUPMJHIUVQPOSBSFPDDBTJPOT*OTVDIBDBTFXBJUGPSBGFXNJOVUFTBOEUIFOUSZBHBJO
t %POPUDPWFSUIFMFOTXJUIUIFMFOTDBQXIJMFUIFMBNQJTPO%POPUTUSJQPGGUIFBMVNJOJVNTIFFUJOTJEFUIF
lens cap.
t "GUFSUIF108&3CVUUPOJTQSFTTFEUIFJNBHFNBZnJDLFSCFGPSFUIFMBNQCFDPNFTTUBCMF5IJTJTOPUB
product malfunction.
t 5IFMBNQPQFSBUJPOCFDPNFTTUBCMFJONJOVUFBGUFSUIFQPXFSJTUVSOFEPOBOEUIFOUIFMBNQNPEFTFMFDUFE
in the menu is activated. During the activation, displayed images may be disturbed.
t 5IFQSPKFDUPSTUBSUTXBSNJOHVQXIFOUIF108&3CVUUPOJTQSFTTFE%VSJOHUIFXBSNVQQSPDFTTJNBHFT
may appear dark and no commands are accepted.
t #ZCMJOLJOHSFEUIF-".1JOEJDBUPSJOEJDBUFTUIBUUIFMBNQTIPVMECFSFQMBDFETPPO3FQMBDFUIFMBNQXIFO
the LAMP indicator blinks red. (See page 71.)
4. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
5. Adjust with the  or  button to get a fine picture.
t 8IFOUIF&/5&3CVUUPOJTQSFTTFEXIJMFUIF;00.'0$64NFOVJTEJTQMBZFEUIFBEKVTUNFOUNPEFJT
switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the  or  button
becomes fast, and it becomes slow when STEP is selected.
6. Select an input source.
t 1SFTTUIF$0.165&3%7*%CVUUPOPOUIFQSPKFDUPSPSUIF$0.165&3$0.165&3PS%7*%)%$1
button on the remote control that is corresponding to the terminal in use.
t 5IFJOQVUTPVSDFJTTXJUDIFEGSPN$0.165&3UP$0.165&3UP%7*BUFWFSZQSFTTPGUIF$0.165&3
DVI-D button on the projector.
t 5IFQSPKFDUPSBVUPNBUJDBMMZTFMFDUTUIFBQQSPQSJBUFTJHOBMGPSNBU5IFTFMFDUFETJHOBMGPSNBUJTEJTQMBZFEPO
the screen.
t :PVDBOOPUDIBOHFUIFJOQVUTPVSDFXIJMFUIFNFOVJTCFJOHEJTQMBZFE
t 5IPVHIJUNBZUBLFTPNFUJNFCFGPSFBOJNBHFJTEJTQMBZFEPOUIFTDSFFOEFQFOEJOHPOUIFUZQFPGUIFJOQVU
signal, such symptom is not a malfunction.
t *NBHFTNBZOPUCFQSPKFDUFEJOUIFDPSSFDUQPTJUJPOEFQFOEJOHPOUIFUZQFPGUIFJOQVUTJHOBM*OTVDIBDBTF
press the AUTO POSITION button. (See page 24.)
t 8IFO$0.165&3PS$0.165&3JTDIPTFOBTUIFTPVSDFJNBHFTTVQQMJFEGSPNUIFDPNQVUFSNBZ
flicker. Press the  or  button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specified sizes.
8.
Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 11.)
t When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 14.)