Instruction manual

55
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Operations
ENGLISH
When using “DATE/TIME” in the <SEARCH SELECTION>
screen, the number of list items displayed on the screen can
be narrowed down.
1. Press the SEARCH button to display the <SEARCH
SELECTION> screen.
2. Set the desired date and time of the result in “DATE/
TIME” and confirm.
3. Turn the SHUTTLE ring counterclockwise once to
display narrowed-down list.
4. Select the desired alarm list number and turn the
SHUTTLE ring clockwise to confirm.
• To cancel the search, press the SEARCH button.
• After performing alarm search, the screen will be in the single
screen display with still-frame playback regardless of whether
setting “ALL” in the above “SELECTION CAMERA NO.” or
selecting an individual camera number. The search result of
emergency recording will display the still-frame screen of the
smallest camera number.
5. Playback the search result.
• Press either the PLAY (REV. PLAY) or PAUSE button.
6. To stop playback or still-frame playback, press the STOP
button.
7. To clear the search screen, press the SEARCH button.
■ START/END SEARCH
It is possible to search the recording starting/ending point
of the device selected in <TIME DATE SEARCH>, <IN-
DEX SEARCH> and <ALARM INDEX SEARCH> for play-
back.
1. Press the SEARCH button.
• The search screen selected in above “SEARCH TYPE”
appears.
2-1. (To play back the oldest recording • • • )
Select “START” and turn the SHUTTLE ring clockwise.
2-2. (To play back the last recording • • • )
Select “END” and turn the SHUTTLE ring clockwise.
• After performing START/END SEARCH :
• For TIME DATE SEARCH andALARM INDEX SEARCH,
SPLIT9 screen is displayedwhen setting the above
“SELECTION CAMERA NO.” to “ALL”. Single screen with
still frame playback is displayed when selecting individual
camera number.
• SPLIT9 screen is always displayed for INDEX SEARCH.
3. Playback the search result.
• Press the PLAY (REV. PLAY) or PAUSE button.
4. To stop playback or still-frame playback, press the STOP
button.
5. To clear the search screen, press the SEARCH button.
！
To change the SPLIT9 screen during still-frame
playback to single screen display of the desired
camera number, press the SEARCH button to clear
the search mode screen and press the desired cam-
era number button.
In the alarm list, items with the ALARM IN termi-
nal on the rear grounded are indicated in white, items
that were detected with motion are indicated in green
and items with the EMERGENCY terminal grounded
are indicated in red.
To clear the alarm list, erase the data in the <HDD
DATA CLEAR> screen. Alarm recording then will be
stored again from 00001.
1. Press the SEARCH button.
• The search screen selected in above “SEARCH TYPE”
appears.
<SEARCH SELECTION>
>> SEARCH TYPE ALARM LIST
SELECTION CAMERA NO. ALL
DATE/TIME - - : :
PLAYBACK DEVICE HDD
START 02-02-2002 00:00:00
END 04-04-2002 12:30:15
2. (When the desired search screen is not displayed on the
screen • • • )
Change the above “SEARCH TYPE” setting and display the
“ALARM LIST SEARCH” screen.
• To display the emergency recording start time in the alarm
list, set “SELECTION CAMERA NO.” in the <SEARCH
SELECTION> screen to “ALL”. “E” indicating emergency
recording will appear next to the camera number in the alarm
list.
<ALARM LIST SEARCH>
>> 00004 01-01-2001 00:00:04
00003 01-01-2001 00:00:03 E
00002 01-01-2001 00:00:02
00001 01-01-2001 00:00:01 E
1
2
3. Select the desired alarm list number.
• button/turn JOG dial counterclockwise : Selection moves
to the next number.
• button/turn JOG dial clockwise : Selection moves to the
previous number.
• button : Displays the page with date prior to the date of
the currently opened page.
• button : Displays the page with date newer than the date
of the currently opened page.
• To cancel search, press the SEARCH button.
！
The camera number written by the start index
signal of the pre-alarm recording may differ from the
camera number displayed in the alarm list.
！
When setting “HDD REPEAT REC” to “OFF” or
“STANDBY” and there is an alarm recording (emer-
gency recording) at the end of the HDD, that record-
ing may not be stored in the alarm list and that
number may become missing and not displayed.
When an alarm recording (emergency recording) is
performed using display of the <ALARM LIST SEARCH>
screen, exit the <ALARM LIST SEARCH> screen and display
the screen again. The new item will be added to the list.