Operation Manual

4
Ventilation display
Displayed during ventilation operation
☞ See page 12
Weekly timer display
Displays the settings of the
weekly timer.
Operation setting display area
Displays setting temperature, airflow
volume, operation mode and operation
message.
Operation/check indicator light
During operation: Lit in green
In case of error: Flashing in red
Operation/stop button
This button is used to operate and stop
the air conditioning system.
Press the button once to operate
the system and press it twice
to stop the system.
MODE button
This button is used to change the
operation mode.
FAN SPEED button
This button is used to set the airflow
volume.
VENT button
This button is used to operate external
ventilator. ☞ See page 12
LOUVER button
This button is used to operate/stop the
swing louver. ☞ See page 11
SET button
•This button is used to fix the setting.
•This button is used to set the silent mode.
☞ See page 5 to 12
RESET button
•If you press this button while making settings,
you can go back to the previous operation. ☞ See page 5 to 12
•This button is also used to reset the “FILTER CLEANING” display.
(Press it after cleaning the air filter)
Central control display
Displayed when the air conditioning system is
controlled by centralized remote control.
Timer operation display
Displays the timer operation setting.
Temperature setting buttons
These buttons are used to set the
temperature of the room.
Timer button
This button is used to set
the timer mode.
☞ See page 5
Timer setting buttons
These buttons are used to set
the timer mode and the time.
☞ See page 5 to 12
E.S.P. button
This button is only used by service
engineers for installation purposes.
AIR CON No. button
•Display the indoor unit number connected to this
remote control.
•This button is used for indoor unit address setting.
CHECK button
This button is only used by service engineers
for installation purposes.
TEST button
This button is used during test operation.
NAMES AND FUNCTIONS OF REMOTE CONTROL BUTTONS (WIRED REMOTE CONTROL)
Wired remote control
• Thefigurebelowshowstheremotecontrolwiththecoveropened.Notethattheitemsintheliquid
crystaldisplay(LCD)areaareshownforexplanationpurpose.
Pull the cover downwards to open.
HOW TO USE< WIRED REMOTE CONTROL >
PRECAUTIONS FOR WASTE DISPOSAL
Your Air Conditioning product may be marked with this symbol. It means that waste electrical and
electronic equipment (WEEE as in directive 2012/19/EU) should not be mixed with general household
waste. Air conditioners should be treated at an authorized treatment facility for re-use, recycling and
recovery and not be disposed of in the municipal waste stream. Please contact the installer or local
authority for more information.
PRECAUTIONS FOR RELOCATION
OR REPAIRING
CAUTION
Neverperformany
modification.Contact
yourdealerforrepairing.
Improper repairing may lead to
water leakage, electric shock
or fire. Normally the refrigerant
does not leak. But if it leaks
and contacts fire such as
fan heater, space heater or
cooking heater, it may produce
toxic chemicals. When repairing
refrigerant leakage, determine
the service with the service
staff that the repair has been
finished without fault.
Ifitisrequiredto
relocationandreinstall
theunit,consultyourdealer
oraspecialist.
Improper installation of air
conditioning unit may cause
water leakage, electric shock
and/or fire.
Beforerepairingor
checkingindoorunit,be
suretoturnoff“Indoorunit
powersupplybreaker”.
It can result in electric shock or
injury due to rotation of indoor
unit fan if you perform check
or repair with the “Indoor unit
power supply breaker” turned
on.
Placethepanelsremoved
forrepairingorchecking
onthestablespot.
Otherwise, dropping or falling
may lead to injury.