USER’S MANUAL FX2N-1RM-E-SET PROGRAMMABLE CAM SWITCH
FX2N-1RM-E-SET Programmable Cam Switch Foreword • This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the Programmable Cam Switch FX2N-1RM-E-SET. It should be read and understood before attempting to install or use the unit. • For handling of the FX2N/FX2NC Series PLC main unit and FX2N Series extension blocks as well as details of instructions, refer to the corresponding Hardware manuals and programming manuals offered separately.
FX2N-1RM-E-SET Programmable Cam Switch Programmable Cam Switch FX2N-1RM-E-SET USER’S MANUAL Manual number : JY992D71101 Manual revision : K Date : December 2011 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
FX2N-1RM-E-SET Programmable Cam Switch MS,MS-DOS and Windows are registered trademarks of Microsoft Corporation. IBM and AT are registered trademarks of International Business Machines Corporation. All other brand and product names are trademarks or registered trademarks of theirrespective owners.
FX2N-1RM-E-SET Programmable Cam Switch FAX BACK Mitsubishi has a world wide reputation for its efforts in continually developing and pushing back the frontiers of industrial automation. What is sometimes overlooked by the user is the care and attention to detail that is taken with the documentation. However, to continue this process of improvement, the comments of the Mitsubishi users are always welcomed. This page has been designed for you, the reader, to fill in your comments and fax them back to us.
FX2N-1RM-E-SET Programmable Cam Switch iv
FX2N-1RM-E-SET Programmable Cam Switch Guidelines for the safety of the user and protection of the Programmable Cam Switch FX2N-1RM-E-SET This manual provides information for the use of the programmable cam switch FX2N-1RM-E-SET. The manual has been written to be used by trained and competent personnel.
FX2N-1RM-E-SET Programmable Cam Switch • Under no circumstances will Mitsubishi Electric be liable responsible for any consequential damage that may arise as a result of the installation or use of this equipment. • All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.
FX2N-1RM-E-SET Programmable Cam Switch Contents 1. Introduction ......................................................................................... 1-1 1.1 Outline of the product ........................................................................................ 1-1 1.2 Features ............................................................................................................ 1-1 1.3 Product configuration ................................................................................
FX2N-1RM-E-SET Programmable Cam Switch Contents 8. Program Operating Procedures .......................................................... 8-1 8.1 Functions offered by the data setting panel ...................................................... 8-1 8.2 Basic operating procedures .............................................................................. 8-3 8.2.1 Common items ..................................................................................................................... 8-3 8.2.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 1. Introduction 1 Introduction This section describes the outline of the programmable cam switch FX2N-1RM and introduces the peripheral equipment. 1.1 Outline of the product The programmable cam switch FX2N-1RM (hereinafter referred to as FX2N-1RM or unit) detects the rotation angle of a machine using a brushless resolver, and turns on/off up to 48 points of transistor outputs at a programmed angle (position).
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 < Mechanical cam-operated switch > 48-step cam disc (8 teeth maximum/disc) 48 limit switches (1 switch/disc) 1-2
FX2N-1RM-E-SET Programmable Cam Switch 1.3 Introduction 1 Product configuration The FX2N-1RM package contains the following components. • • • • Outside dimensions and name of each part 1) 2) 3) 4) 50(1.97) 21(0.83) Dimensions: mm (inch) Weight: approx.0.5kg 5) 8) 30(1.18) 6) 9) 10) 80(3.15) 90(3.54) 111(4.37) 7) 90(3.54) 1.4 Programmable cam-operated switch FX2N-1RM (including data setting panel) Signal cable FX2N-RS-5CAB Resolver F2-720RSV Extension cable to connect PLC (55 mm(2.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 50(1.97) 54(2.13) φ9(0.35) 38(1.50) 5000(196.85) φ31(1.22) 19(0.75) [Unit: mm (inch)] (option) 5000(196.85) 54(2.13) φ31(1.22) φ28(1.10) φ9(0.35) 54(2.13) Mounting hole 4-f4.5(0.18) 10(0.39) 45(1.77) f40(1.57) 45(1.77) 0 -0.015(0.0006) 4.36(0.17) f10(0.39) ) 97 1. ( 0 f5 0 f33.32(1.31) -0.05(0.002) 45(1.77) 9.5(0.37) 4.36(0.17) 3(0.12) 28(1.10) 4(0.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 1.5 System configuration 1.5.1 Connecting the FX2N-1RM to PLC FX2N-1RM PLC FX 2N / FX2NC FX2N-1RM FX2N-1RM X000~X017 BANK L COM 24+ N X1 X2 X3 X4 X7 X10 X13 X14 X15 BANK OUT X16 BANK OUT RUN RUN ERR IN 0 1 2 3 4 5 6 7 10 11 12 13 14 15 16 17 STEP DEG RUN BATT.V PROG.E OUT Y1 Y2 Y3 Y4 Y5 Y6 0 1 2 3 4 5 6 7 10 11 12 13 14 15 16 17 Y10 Y12 COM3 Y11 Y13 Y14 CPU.
FX2N-1RM-E-SET Programmable Cam Switch • • • Introduction 1 Only output extension blocks are allowed to be connected to the FX2N-1RM. (Even if extension blocks dedicated to input are connected, no input can be received and input Nos. are not assigned.) Each data or bit information can be read and written between the PLC main unit and the FX2N-1RM using FROM/TO instructions.
FX2N-1RM-E-SET Programmable Cam Switch 1.5.
FX2N-1RM-E-SET Programmable Cam Switch 1.5.3 Introduction 1 CC-Link connection Composition FX2N-1RM BANK FX2N-32CCL • When one FX2N-1RM is used in CC-Link, FX2N-32CCL interface block (here in after referred to as FX2N-32CCL) is connected with the connector for the extension block connection FX2N-1RM. • FX2N-32CCL can not be used together with the output extension blocks. • Refer to user’s manual of this bale in FX2N-32CCL and connection with master unit.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 Composition F X L C O M N E x te b lo E x te u n s e r ie s P L C 2 N 2 4 + X 1 X 2 X 3 X 4 X 7 IN X 1 0 0 X 1 4 X 1 3 1 2 3 4 5 X 1 5 6 n s io n c k s n s io n its F X O U T 0 1 2 3 4 5 6 7 X 1 6 7 P O W E R 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 -3 2 C C L 2 N B A N K F X 2 N O U T • • • Y 4 Y 5 Y 6 0 1 2 3 4 5 6 7 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 Y 1 0 Y 1
FX2N-1RM-E-SET Programmable Cam Switch 1.5.4 Introduction 1 Resolver and connection cable Relay cable F2-RS-5CAB 5m(196.85 inch) Resolver F2-720RSV Signal cable FX2N-RS-5CAB 5m(196.85 inch) FX2N-1RM main body When the signal cable is not long enough, relay cables can be connected for extension as shown in the figure above. Two or more relay cables can be used. The maximum extension length is 100 m (3937 inch).
FX2N-1RM-E-SET Programmable Cam Switch 1.5.5 Introduction 1 Connecting the peripheral equipment < Data setting panel > This panel allows data setting, data read, monitoring, copy between banks, teaching and fine adjustment in the RUN mode. Data setting panel When removing the data setting panel, press the attachment buttons provided at the top and the bottom of the data setting panel.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 < Personal computer > A personal computer allows save and transfer of programs.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 The FX-20P-E allows the save and transfer of programs. Use the FX-20P-RWM and a memory cassette to save programs.
FX2N-1RM-E-SET Programmable Cam Switch 1.5.6 Introduction 1 Cautions on use of a personal computer and the FX-20P-E • Only the program transfer function is available from a personal computer or the FX-20P-E to the FX2N-1RM. The monitor function, the test function, the current value change function, etc. are not available. (If such a function is used, a communication error occurs.) Set the parameter as shown in the table below when transferring programs.
FX2N-1RM-E-SET Programmable Cam Switch • Introduction 1 The table below shows the applicable versions for personal computers and the FX-20P-E. FX2N-1RM Peripheral equipment V. 2.20 or earlier FX-PCS/WIN-E(V.1.00 to V.2.11) V. 2.30 or later applicable FX-PCS/WIN-E(V.3.00 or later) not applicable applicable GX Developer not applicable applicable from SW2D5-GPPW-E FX-20P-E applicable from V. 3.
FX2N-1RM-E-SET Programmable Cam Switch Introduction 1 Memo 1-16
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 2. Installation 2 Installation This section describes how to install the FX2N-1RM and the resolver. 2.1 Installation method The FX2N-1RM can be mounted via a DIN rail or directly mounted with M4 screws. < When mounted via a DIN rail > The FX2N-1RM can be mounted to a DIN rail DIN 46277 (Width: 35 mm (1.38 inch)) without any modification. When removing the FX2N-1RM, pull the DIN rail mounting hook downward.
FX2N-1RM-E-SET Programmable Cam Switch Installing the resolver When installing a resolver, pay rigid attention to eccentricity of the rotation shaft and tilt of the shaft. Attach a resolver to a machine via an elastic coupling. Example: NA-15 (φ10 (0.39 inch) × φ10 (0.39 inch)) manufactured by Nihon Miniature Coupling Coupling Resolver Screw (M4) 10(0.39) 1°30'(1.3 degrees) or less 35(1.38) φ10(0.39) φ22(0.87) φ10(0.39) φ 50 0.1(0.004) or less 2.3 Installation 2 7 (1.
FX2N-1RM-E-SET Programmable Cam Switch Installation 2 Cautions on installation • Use the unit in the environment in accordance with the environmental specifications described in Paragraph 3.1 in this manual. Do not use the unit in a place with dust, soot, conductive dust, corrosive gases (Salt air, Cl2, H2S, SO2, NO2, etc.) or flammable gases. Do not use in places exposed to high temperature, condensation, wind and rain, vibrations or possible impacts.
FX2N-1RM-E-SET Programmable Cam Switch Installation 2 Note • • • • Never let the signal input line and the signal output line of the PLC go through the same cable. Never let the signal input line and the signal output line of the PLC go through the duct together with other power lines and output lines. Never bind the signal input line and the signal output line of the PLC together with other power lines and output lines.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 3. Specifications 3 Specifications This section describes the specifications of the FX2N-1RM and the resolver. Cautions on design • Provide a safety circuit outside the PLC so that the entire system can operate conservatively in any case even if an error has occurred in the external power supply or a failure has occurred in the PLC. If a safety circuit is not provided, an accident may occur caused by malfunction or erroneous output.
FX2N-1RM-E-SET Programmable Cam Switch 3.1 Specifications 3 General specifications Ambient 0 to 55°C when operating and -20 to 70°C when stored temperature Ambient humidity Vibration resistance 35 to 85% RH (no condensation) when operating When installed on DIN rail When installed directly Frequency (Hz) Acceleration (m/s2) Half amplitude (m/m) 10 to 57 – 0.035 57 to 150 4.9 – 10 to 57 – 0.
FX2N-1RM-E-SET Programmable Cam Switch 3.2 3.3 Specifications 3 Performance specifications Applicable PLC The bus of an FX2N, FX3U, FX2NC and FX3UC series PLC can be connected. A single drive is also possible. (Refer to subsection 1.5.1.) Program memory Built-in EEPROM memory (no battery) Number of cam output points 48 internal output points. Data is read by PLC. In addition, 48 points can be connected when transistor output extension blocks or triac output extension blocks are connected.
FX2N-1RM-E-SET Programmable Cam Switch 3.4 Specifications 3 Power supply specifications Rated voltage 24 VDC+10%, -15% Allowable instantaneous power 5ms interruption period Power consumption 3.5 3 W (when operating individually), 5 W (at 32 points output ON) Input specifications Input signal voltage 24 VDC ±10% Input signal current 7 mA/24 VDC Input ON current 4.5 mA or more Input OFF current 1.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 4. External Wiring 4 External Wiring This section describes wiring of the power supply and the input. Cautions on wiring • Do not connect the AC power supply to DC I/O terminals or DC power terminals. If such connection is performed, the FX2N-1RM may burned out. • Do not perform wiring from the outside to an unused terminal [ ⋅ ] of the main unit or an extension block. If such wiring is performed, the unit may be damaged.
FX2N-1RM-E-SET Programmable Cam Switch 4.1 External Wiring 4 Wiring of the power supply and the input Use transistors when a bank is switched in the RUN mode. FX2N-1RM B0 B1 3.3kΩ 3.3kΩ S/S +10% DC24V -15% *1 The service power supply of the PC can be used within the allowable capacity. 24+ 24- Class D grounding Use transistors when a bank is switched in the RUN mode.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 5. Extension Block Specifications and External Wiring 5 Extension Block Specifications and External Wiring This section describes the specifications and the wiring of the FX2N-16EYT. When other extension blocks dedicated to output are used, refer to the Hardware Manual of the FX2N Series PLC in accordance with the model used. 5.
FX2N-1RM-E-SET Programmable Cam Switch Extension Block Specifications and External Wiring 5 Cautions on wiring • Do not connect the AC power supply to DC I/O terminals or DC power terminals. If such connection is performed, the FX2N-1RM may burned out. • Do not perform wiring from the outside to an unused terminal [ ⋅ ] of the main unit or an extension block. If such wiring is performed, the unit may be damaged.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 6. Basic Setting 6 Basic Setting This section describes the basic setting of the FX2N-1RM including handling of the RUN and STOP modes, specification of the bank No., setting of the automatic angle advance function and setting of the reference angle. Cautions on start-up and maintenance • Do not touch any terminal while the power is supplied. If a terminal is touched, electrical shocks or malfunction may occur.
FX2N-1RM-E-SET Programmable Cam Switch 6.1 Basic Setting 6 Handling of the RUN and PRG modes The FX2N-1RM offers two modes, RUN (operation) and PRG (program). These modes can be switched using the following procedure. (In the PRG mode, the FX2N-1RM stops operation.) < Built-in RUN/PRG selector switch > T h e RU N m o d e a n d t h e P R G m o d e c a n b e sw i t c h e d by manipulating the RUN/PRG selector switch built in the main unit. When the switch is set to the RUN side, operation is performed.
FX2N-1RM-E-SET Programmable Cam Switch 6.2 Basic Setting 6 Specifying the bank The FX2N-1RM can store two or more programs, and execute an arbitrary program in accordance with an external input to the FX2N-1RM or an instruction given by the PLC main unit. Up to 4 banks are available for an external input. Up to 8 banks are available for an instruction by the PLC. • Setting the bank specification method Set which one between the external input and the PLC is used to specify a bank.
FX2N-1RM-E-SET Programmable Cam Switch 6.3 Basic Setting 6 Automatic angle advance function The automatic angle advance function performs the output ON/OFF operation in advance by an arbitrary angle (angle advance quantity) in accordance with the rotation speed of the resolver. By using this function, delay in the mechanical operation generated during rotation at high speed can be compensated.
FX2N-1RM-E-SET Programmable Cam Switch Basic Setting 6 < Assignment of FNC Nos. and BFM Nos. > S0 S1 S2 S3 S4 S5 S6 Input from data setting panel (FNC No.) Input from main unit (BFM No.
FX2N-1RM-E-SET Programmable Cam Switch 6.4 Basic Setting 6 Individual automatic angle advance function The automatic angle advance function performs the output ON/OFF operation in advance with an arbitrary angle (angle advance quantity) in accordance with the rotation speed of the resolver. This setting does an individual setting to the on angle and the off angle of output Y00 to Y03. The executed program number can be used from bank 0 to bank 6. Bank 7 must not be used.
FX2N-1RM-E-SET Programmable Cam Switch • Basic Setting 6 Please separate angle advance quantity from previous ON/OFF 1 degree (1 degree mode) or 0.5 degrees (0.5 degrees mode) or more. (Refer to the figure 1 below) Figure 1 ON angle advance quantity OFF angle advance quantity ON angle advance quantity OFF angle advance quantity Y0 Individual automatic angle advance function unused. Y0 Individual automatic angle advance function used. 1 degree or 0.5 degrees or more 1 degree or 0.
FX2N-1RM-E-SET Programmable Cam Switch Basic Setting 6 When individual automatic angle advance function is used, addition of the crack of rotation speed and angle advance quantity to buffer memory (BFM) is as follows. • When the mode is selected 1 degree (360 degrees/ ON angle OFF angle revolution), input equals advance quantity advance quantity advance angle value. 6378 6377 When the mode is selected 6381 6380 0.
FX2N-1RM-E-SET Programmable Cam Switch 6.5 Basic Setting 6 Setting the reference angle Originally, the brushless resolver has an absolute reference angle. In addition, a reference angle in accordance with a machine can be set. Each set angle of the FX2N -1RM performs its operation based on the reference angle set in accordance with the machine. The reference angle can be set by the data setting panel or by a TO instruction given by the PLC main unit.
FX2N-1RM-E-SET Programmable Cam Switch 6.6 Basic Setting 6 Handling the keyword < Limitation of the function by the keyword > When a keyword is registered, writing to the EEPROM is prohibited in the same way as the EEPROM protect function. When programs are read by a personal computer or the FX-20P-E, the registered keyword must be entered. (Preventing theft of a program) A keyword can be registered/deleted using the data setting panel, the personal computer software and the FX-20P-E.
FX2N-1RM-E-SET Programmable Cam Switch 6.7 Basic Setting 6 Current angle transfer function The current angle transfer function to transfers the current angle of the resolver to BFM#106 via turning ON input terminal B1. (This function has been included since V2.40) The PLC is used together, and a highly accurate sampling by which an external input is made a trigger can be done. The response speed becomes 207r/min/0.5degree or 415r/min/degree.
FX2N-1RM-E-SET Programmable Cam Switch Basic Setting 6 < Action of current angle transfer function> 200µs 200µs or more or more ON Input terminal B1 ON OFF OFF OFF 98 Current angle (BFM#8) Value of BFM#106 • • • • 1 2 -1 3 200µs or more 4 5 99 100 101 102 103 104 6 5 100 Transfer the current angle of the resolver to BFM#106 by turning ON input terminal B1. The input signal to input terminal B1 is necessary for both 200µS or more the turning ON time and the turning OFF time.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 7. BFM Assignment 7 BFM Assignment This section describes the buffer memory (BFM) of the FX2N-1RM. When the FX2N Series PLC is connected to the FX2N-1RM, data can be read/written from/to the BFM by FROM/TO instructions. (Refer to Paragraph 7.3.) When two or three FX2N-1RM units are connected, FROM/TO instructions are available in only the unit nearest to the PLC main unit.
FX2N-1RM-E-SET Programmable Cam Switch BFM No. Name BFM Assignment 7 Initial Remarks R: For read W: For write value K: Keep #26 Angle advance quantity of a u t o m a t i c a ng l e a d va n c e S 6 (degrees) 0 #27 Undefined ⎯ Status 0 #28 #8028 #9028 *1 ... ... 0 ... ... Speed of automatic angle advance S6 (r/min) ... ... #25 File register assignment No. ⎯ W, K D7158 W, K D7159 ⎯ ⎯ ⎯ ⎯ R ⎯ ×1 value (1 degree), ×2 value (0.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 *1: When two or more FX2N-1RM units are connected to the PLC main unit, data is read from and written to each unit via the buffer memory of the unit nearest to the PLC main unit. The relationship between the BFM Nos. and the units is shown below. BFM Nos. of one or two digits: FX2N-1RM unit nearest to the PLC main unit BFM Nos. of 8000 to 8999: Second FX2N-1RM unit BFM Nos.
FX2N-1RM-E-SET Programmable Cam Switch 7.2 BFM Assignment 7 Description on BFM < BFM #0: Initial setting > Bit Description Initial value Remarks b0 Resolution 0 1: 0.5 degree (720 degrees/rotation), 0: 1 degree (360 degrees / rotation) *1 b1 Rotation direction of resolver 0 1: Counterclockwise 0: Clockwise b2 Write-protect of EEPROM 0 1: Write to EEPROM is disabled. 0: Write is enabled. (However, BFM #0 b2 can be modified.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 < BFM #3: Command > Bit Description Remarks b0 RUN Runs a program (on rising edge). Refer to Paragraph 7.1. b1 PRG Turns off output by PRG command (received on rising edge). Refer to Paragraph 7.1. b2 ADJ Sets reference angle on rising edge in PRG mode. Refer to Paragraph 7.4. *4 b3 Error reset Resets error information (received on rising edge).
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 < BFM #4 to BFM #6: Output prohibition > Example of BFM #4 Bit Description Remarks b0 Y00 output prohibition 1: Prohibits output., 0: Enables output. b1 Y01 output prohibition 1: Prohibits output., 0: Enables output. b2 Y02 output prohibition 1: Prohibits output., 0: Enables output. b3 Y03 output prohibition 1: Prohibits output., 0: Enables output. b4 Y04 output prohibition 1: Prohibits output., 0: Enables output.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 < BFM #10 to BFM #12: Output status > Example of BFM #10 Bit Description Remarks b0 Y00 output status 1: Y01 output ON operation, 0: Y01 output OFF operation b1 Y01 output status 1: Y01 output ON operation, 0: Y01 output OFF operation b2 Y02 output status 1: Y01 output ON operation, 0: Y01 output OFF operation b3 Y03 output status 1: Y01 output ON operation, 0: Y01 output OFF operation b4 Y04 output status 1: Y01 output ON operation,
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 < BFM #28: Status > Bit Description Remarks b0 Operating Turned on while operation is normal in RUN mode (Functions in same way as RUN LED.). b1 Rotating clockwise Turned on while rotating in RUN mode with BFM #0 b1 set to 0. b2 Rotating counterclockwise Turned on while rotating in RUN mode with BFM #0 b1 set to 1. b3 Error occurred Turns off output. Turned off when error is reset (Functions in same way as ERROR LED.).
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 The data of the turning on angle and the turning off angle can be indirectly set from a PLC main unit to two or more outputs of FX2N-1RM. (It is a function added from version V2.00) After the turning on angle and the turning off angle data are written in BFM #100, #101, the BFM number which wants to be written is written BFM #102.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 < Timing at which a program is saved to the EEPROM > 1 ) While the data setting panel is manipulated Every time a program is modified using the data setting panel, the modified data is written to both the buffer memory and the EEPROM. 2 ) While the RUN mode is selected When the bank is switched, the contents of a new bank are saved in the EEPROM.
FX2N-1RM-E-SET Programmable Cam Switch 7.3 BFM Assignment 7 Cautions on creation of a sequence program When the ON/OFF angle of the FX 2N -1RM is set using a program in the PLC main unit, a watchdog timer error may occur if many settings are performed at a time. When a large value is written to D8000 while setting is performed using the initial pulse, a watchdog timer error may also occur because such a written value becomes valid only when an END instruction is given.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 7.4 Program example 7.4.1 Program example which uses FROM/TO instruction A program example using FROM/TO instructions is shown below. In this program, the FX2N-1RM is switched to the RUN mode by input to X000 in the PLC main unit, and switched to the PRG mode by input to X001. When actual conditions differ from those in the program shown below, change the program to suit the application accordingly.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 Use the program example shown below when the resolver rotation speed is low at startup, stop, etc. and the current angle and output status are unstable.
FX2N-1RM-E-SET Programmable Cam Switch 7.4.2 BFM Assignment 7 Program example which uses indirect specification (BFM #100 to #105) The bank number and the output number are specified with Graphic Operation Terminal GOTF900 series connected with a PLC. And, writing and reading are done to the ON/OFF angle of all patterns. (step 0 to step 7) Writing and reading the ON/OFF angle are indirectly done. (BFM #100 to #105 is used.
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 0 M10 M11 • The BFM number is specified based on output number specification(D1: 0 to 57) Octal number→decimal number...
FX2N-1RM-E-SET Programmable Cam Switch BFM Assignment 7 Memo 7-16
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 8. Program Operating Procedures 8 Program Operating Procedures This section describes the program operating procedures in the FX2N-1RM using the data setting panel. 8.1 Functions offered by the data setting panel < Data setting panel function list > In addition to the following list. There is a monitor mode (refer to 9.1) and a test mode (refer to 10.1) Item Function Mode Description page Read Reads a program. PRG 8-3 Write Writes and modifies a program.
FX2N-1RM-E-SET Programmable Cam Switch Program Operating Procedures 8 Function Mode Description page Batch addition of OFF output set angle Adds specified angle to OFF set angle of specified output at a time. PRG 8-25 Batch subtraction of OFF output set angle Subtracts specified angle from OFF set angle of specified output at a time. PRG 8-25 BCD output (negative logic) Outputs current angle as BCD from a cer tain output No. (negative logic).
FX2N-1RM-E-SET Programmable Cam Switch Program Operating Procedures 8 8.2 Basic operating procedures 8.2.1 Common items • When the power is turned on, the following initial screen is displayed on the data setting panel. < When the PRG mode is selected > BANK OUT STEP DEG ON LED OFF LED 0 0 0 Blank*1 Lit Extinguished *1: When an angle is already set to the output Y0, that ON angle is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.3 Program Operating Procedures 8 [Power ON] [PRG mode] Write and modification Read the step No. to be written or modified, then set the ON/OFF angle of the output. When writing new data, perform the write operation in the order of "ON angle" and "OFF angle". When modifying the existing data, the ON angle or the OFF angle can be modified separately. BANK 0 GO Read the program bank No. 0. OUT 0 GO Read the output Y00. STEP 0 GO Read the step No. 0.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.4 Program Operating Procedures 8 [Power ON] [PRG mode] Insertion Insertion is performed to the steps Nos. 0 to 6 of the same bank and the same output No. When data is inserted into an arbitrary step, the steps after the specified step are shifted backward by 1 step respectively, and the set value is written. At this time, if a set value is already written to the step No. 7, shift backward is disabled and the error E06 occurs.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.5 Program Operating Procedures 8 [Power ON] [PRG mode] Deletion Delete the entire program, the bank data, the output data or the step data (ON/OFF). The entire program contains the bank data, the output data, the step data and the keyword.
FX2N-1RM-E-SET Programmable Cam Switch Program Operating Procedures 8 Deleting a specified output BANK 0 OUT GO 0 GO Specifies the bank No. 0. Specify the output Y00. DEL OUT GO GO ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > BANK 0 OUT STEP DEG ON LED OFF LED 0 ### *1 Lit Extinguished 0 *1 The ON angle of the output Y00 already registered is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.6 Program Operating Procedures 8 [Power ON] [PRG mode] Copy Copy the contents of an existing bank to a specified bank. Copy the contents of an existing output to a specified output of the same bank. Copying a bank BANK 0 GO Specify the copy source. CPY BANK Specify the copy destination. 1 GO The error indication "E07" is displayed when the bank No. specified as source is equivalent to the bank No. specified as destination.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.7 Program Operating Procedures 8 [Power ON] [PRG mode] Write and modification of teaching Treat the current position of the resolver as the set value. Connect the resolver to the FX2N-1RM before turning on the power. BANK 0 GO Read the program bank No. 0. OUT 0 GO Read the output Y00. STEP 0 GO Read the step No. 0. Start to set the ON angle of the output Y00. TEACH Stop the resolver in a position in which it is to be rotated.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.8 Program Operating Procedures 8 [Power ON][PRG mode] Insertion of teaching Insert the current position of the resolver as the set value. Connect the resolver to the FX2N-1RM before turning on the power. BANK 0 GO Read the program bank No. 0. OUT 0 GO Read the output Y00. STEP 0 GO Read the step No. 0. CLR Select the insertion mode. TEACH Start to set the ON angle of the output Y00.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.9 Program Operating Procedures 8 [Power ON] [RUN/ PRG mode] Changing over the mode between RUN and PRG Change-over the mode between RUN and PRG from the data setting panel. RUN RUN GO ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > BANK OUT STEP DEG 0 0 0 "RUN" flashes Example of current value display BANK OUT STEP DEG RUN LED 0 Blank Blank ### *1 Lit *1 The current value is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.2.10 Program Operating Procedures 8 [Power ON][PRG mode] Reading/setting the reference angle Set the current position of the resolver as the reference angle. The reference angle is used as common in all the banks. Connect the resolver to the FX2N-1RM before turning on the power. Read procedure Display the reference angle. ADJ Return the display to the previous status.
FX2N-1RM-E-SET Programmable Cam Switch 8.3 Program Operating Procedures 8 Application operating procedures An application operating procedure indicates a monitor operating procedure, a test operating procedure or an operating procedure using the [FNC] key. The contents when the [FNC] key is used vary depending on the FNC No. entered after the [FNC] key. The FNC Nos. available are 0 to 6, 13 to 26, 50, 60 to 65, 70 to 75, 80, 84 and 90. 8.3.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.3 Program Operating Procedures 8 [Power ON] [PRG mode] Write-protect function of the EEPROM [FNC2] Enable or prohibit write of data to the EEPROM built in the FX2N-1RM. FNC 2 GO ON OFF GO 8.3.4 ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > BANK OUT STEP DEG ON LED OFF LED 0 0 0 F02 Extinguished Lit*1 *1 Initial value (write enabled).
FX2N-1RM-E-SET Programmable Cam Switch 8.3.5 Program Operating Procedures 8 Setting the automatic angle advance function [FNC4, 13 to 26] [Power ON] [PRG mode] Set use of the automatic angle advance angle, the rotation speed and the angle advance quantity. Specifying the automatic angle advance function [FNC4] FNC 4 GO Confirm the setting by referring to the ON/OFF LED status.
FX2N-1RM-E-SET Programmable Cam Switch Program Operating Procedures 8 Angle advance quantity (degrees) of S0 [FNC14] FNC 1 4 GO ON OFF 1 0 · Set the angle advance quantity (180 degrees maximum). A decimal point indicates 0.5 degree. GO ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > BANK OUT STEP d EG 0 *1 DEG "0" is displayed *2 *1 It indicates that S0 is being set. *2 The existing value is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.6 Program Operating Procedures 8 [Power ON] [PRG mode] Individual automatic angle advance function [FNC5,90] The use of individual automatic angle advance function is specified and the rotational speed and angle advance quantity are set. Please make the specification of “use” before setting the rotational speed and angle advance quantity by the undermentioned operation.
FX2N-1RM-E-SET Programmable Cam Switch Program Operating Procedures 8 Setting of rotational speed and angle advance quantity [FNC90] OUT 0 FNC GO 9 0 Specify the output No. (Y00 to Y03) GO *5 ON OFF 1 0 Rotational speed setting of S0. MAX 400rpm(1 degree mode) 207rpm(0.
FX2N-1RM-E-SET Programmable Cam Switch (From previous page) ON OFF 4 0 ON angle advance quantity setting of S0 MAX 180 degrees (Refer to paragraph 6.4) GO *5 (Next page) *5: Refer to 8-29 ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > Program Operating Procedures 8 < Display > It is displayed that DEG display part becomes a blinking display when [ON OFF] key is pushed, and setting is possible.
FX2N-1RM-E-SET Programmable Cam Switch (From previous page) ON OFF 5 0 OFF angle advance quantity setting of S0 MAX 180 degrees (Refer to paragraph 6.4) GO *5 The rotational speed and angle advance quantity of S1 to S6 are set one by one as well as S0. *5: The existing contents of S0 through S6 can be displayed by using the [+] / [-] key. [+] key : The content of the following item setting is displayed. (S0 →S1 . . . →S6) [-] key : The content of the previous item setting is displayed. (S6 →S5 . . .
FX2N-1RM-E-SET Programmable Cam Switch 8.3.7 Program Operating Procedures 8 [Power ON] [PRG mode] Prohibition of RUN to PRG operation [FNC6] The RUN to PRG operation with data setting panel is prohibited. The RUN to PRG switch by the RUN/PRG change switch and BFM#3 is effective. (This function is added from the product since V2.20.). Prohibition of RUN to PRG operathion [FNC6] FNC 6 GO Confirm the setting by referring to the ON/OFF LED status. ON OFF GO 8.3.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.9 Program Operating Procedures 8 [Power ON] [PRG mode] Inverting the output pattern [FNC50] Invert the output pattern of an existing program except the fixed output patterns automatically generated by FNC70 to FNC75. Outputs which are not set in a program cannot be inverted. (The error code "E03" is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.10 Program Operating Procedures 8 Batch addition/subtraction of the output set angle [FNC60, 61] [Power ON] [PRG mode] Add or subtract a specified angle to/from all the steps of a specified output at a time (ON angle and OFF angle) except the fixed output patterns automatically generated by FNC70 to FNC75. Batch addition [FNC60] BANK 0 GO OUT 0 GO FNC 1 6 0 2 3 Specify the output No. to be shifted. GO Enter the angle to be added.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.11 Program Operating Procedures 8 Batch addition/subtraction of the ON output set angle[FNC62, 63] [Power ON][PRG mode] Add or subtract a specified angle to/from the ON set angle of a specified output at a time (only the ON angle) except the fixed output patterns automatically generated by FNC70 to FNC75. If the ON/OFF width becomes 0 by the setting entered, the error code "E08" is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.12 Program Operating Procedures 8 Batch addition/subtraction of the OFF output set angle [FNC64, 65] [Power ON] [PRG mode] Add or subtract a specified angle to/from the OFF set angle of a specified output at a time (only the OFF angle) except the fixed output patterns automatically generated by FNC70 to FNC75. If the ON/OFF width becomes 0 by the setting entered, the error code "E08" is displayed.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.13 Program Operating Procedures 8 [Power ON] [PRG mode] Outputting the BCD current angle [FNC70, 71] Output the BCD current angle. The portion after the decimal point is ignored. The output Nos. of the current angle are Y00 to Y11 (three digits.) The strobe signal is fixed to Y12. (The strobe signal Y12 is used as a signal shared by the three digits.) Only extension blocks dedicated to output can be connected to the FX2N-1RM.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.14 Program Operating Procedures 8 [Power ON] [PRG mode] Outputting the pulse string [FNC72, 73] Output a one- or two-phase pulse string from an arbitrary output No. The number of pulses output is 180 pulses/rotation (for one-phase) or 90 pulses/rotation (for twophase). The rotation speed is determined by the resolution selected. (When 1 degree is selected: 830 r/min, when 0.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.15 Program Operating Procedures 8 [Power ON] [PRG mode] RUN output [FNC74] Output always the ON signal from an arbitrary output No. in the RUN mode. BANK 0 GO OUT 0 GO FNC 7 4 Specify an output No. from which RUN output is to be performed. GO GO 8.3.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.17 Program Operating Procedures 8 [Power ON] [PRG mode] Confirming and deleting the setting When FNC70 to FNC75 are already set, the existing setting can be displayed or deleted using a usual read/deletion operation. Displaying the existing setting [FNC70 to FNC75] BANK 0 GO OUT 0 GO Specify an output No. from which the current value is to be output.
FX2N-1RM-E-SET Programmable Cam Switch 8.3.18 Program Operating Procedures 8 Prohibiting write to the EEPROM and preventing theft of a program [Power ON] [PRG mode] Prohibit write to the EEPROM and prevent theft of a program using a keyword. Reset the write-protect function of the built-in EEPROM (so that write is enabled).
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch 9. Monitor 9 Monitor The display on the data setting panel can be switched among the current value, the status and the rotation speed. This section describes the display change-over procedure and the contents of display. 9.1 Changing over the monitor display [Power ON] [PRG mode] By pressing the [ON OFF] key, the monitor display is switched in the way "current value display → output/status display → rotation speed display".
FX2N-1RM-E-SET Programmable Cam Switch Monitor 9 Memo 9-2
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch Test 10 10. Test This section describes the procedure to modify the set data while the FX2N-1RM is in the RUN mode. 10.1 Operating procedure of the test mode The set data in a program can be modified in the test mode even if the FX2N-1RM is in the RUN mode. However, a program cannot be added or deleted. The set data can be modified in the increment of 0.5 degree using the [+] and [-] keys. (Operations are in accordance with the resolution selected.
FX2N-1RM-E-SET Programmable Cam Switch Test 10 Modifying either the ON angle or the OFF angle ON OFF + The angle is increased by 0.5 degree every time the [+] key is pressed. - The angle is decreased by 0.5 degree every time the [-] key is pressed. GO Determine the modified angle. The set value is written to the EEPROM, and the output is changed. ●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > While the ON LED is lit: The ON angle is modified.
FX2N-1RM-E-SET Programmable Cam Switch Test 10 Modifying the rotation speed of the automatic angle advance function FNC 1 3 GO Set the FNC No. (odd No. among FNC13 to FNC26) After that, the contents of the FNC No. to be modified can be confirmed using the [+] and [-] keys. ON OFF + The rotation speed is increased by 1 r/min every time the [+] key is pressed. - The rotation speed is decreased by 1 r/min every time the [-] key is pressed. (Any numeric cannot be entered.
FX2N-1RM-E-SET Programmable Cam Switch Test 10 Change in individual automatic angle advance function OUT FNC 0 9 GO 0 Specify the output No. (Y00 to Y03) GO [+] / [-] the contents of the item which will be changed with the key the selection and setting can be confirmed. ➀ ON OFF + - GO • 1 rpm or 1 degree increase whenever [+] key is pushed. • 1 rpm or 1 degree decrease whenever [-] key is pushed. (The numerical value cannot be input.) • The content of the change is fixed.
FX2N-1RM-E-SET Programmable Cam Switch Test 10 Cautions on modification of the set value of the automatic angle advance function • The allowable modification range of the rotation speed is 1 to 400 r/min. If the value entered is to overlap the previous or next set value during modification, the [+] or [-] key is not accepted just before the value entered overlaps the previous or next set value. • When the set value of the rotation speed is 0 (initial value), the angle advance quantity is treated as 0.
FX2N-1RM-E-SET Programmable Cam Switch Test 10 Terminating the test mode BANK + CLR Press these keys at the same time. ●●●●●●●●●●●●●●●●●●●●●● < Key operation > < Display > BANK OUT STEP Executed bank No. Blank Blank DEG Displays current value*1 The display status returns to the status before the test mode is selected.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
FX2N-1RM-E-SET Programmable Cam Switch Diagnostics 11 11. Diagnostics This section describes the error indication, the causes and the countermeasures. Errors are classified into ones displayed on the data setting panel and the others written to the BFM #29. 11.1 Indication and causes of errors < Errors displayed o the data setting panel > The errors shown in the table below are displayed on the data setting panel.
FX2N-1RM-E-SET Programmable Cam Switch Diagnostics 11 < Errors written to BFM #29 > The errors shown in the table below are written to BFM #29. Each of these errors is written as an error code to BFM #29 in the FX2N-1RM, and can be read from the PLC main body using a FROM instruction. The same error code is also displayed on the data setting panel. Error indication Causes Countermeasures Target BFM E20 Data outside the allowable range Reset the error status, and enter BFM#1 was set. correct data.
FX2N-1RM-E-SET Programmable Cam Switch 1 Introduction 2 Installation 3 Specifications 4 External Wiring 5 Extension Block Specifications and External Wiring 6 Basic Setting 7 BFM Assignment 8 Program Operating Procedures 9 Monitor 10 Test 11 Diagnostics Appendix
FX2N-1RM-E-SET Programmable Cam Switch
Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Output No.
1832 1848 1864 1880 1896 1912 1928 1944 1960 1976 1992 2008 2024 2040 2056 2072 2088 2104 2120 2136 2152 2168 2184 2200 2216 2232 2248 2264 2280 2296 2312 2328 2344 2360 2376 2392 2408 2424 2440 2456 2472 2488 2504 2520 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 2089 2105 2121 2137 2153 2169 2185 2201 2217 2233 2249 2265 2281 2297 2313 2329 2345 2361 2377 2393 2409 2425 2441 2457 2473 2489 2505 2521 1833 1849 1865 1881 1897 1913 1929 1
Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Output No.
3368 3384 3400 3416 3432 3448 3464 3480 3496 3512 3528 3544 3560 3576 3592 3608 3624 3640 3656 3672 3688 3704 3720 3736 3752 3768 3784 3800 3816 3832 3848 3864 3880 3896 3912 3928 3944 3960 3976 3992 4008 4024 4040 4056 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 3625 3641 3657 3673 3689 3705 3721 3737 3753 3769 3785 3801 3817 3833 3849 3865 3881 3897 3913 3929 3945 3961 3977 3993 4009 4025 4041 4057 3369 3385 3401 3417 3433 3449 3465 3
Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Output No.
Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Output No.
Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Output No.
Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Output No.
Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y30 Y31 Y32 Y33 Y34 Y35 Y36 Y37 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y47 Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Output No. STEP0 ON STEP0 OFF STEP1 ON STEP1 OFF STEP2 ON < Please use this page as a allocation table> STEP2 OFF BFM No. Quick Reference Table for Angle Setting STEP3 ON BFM No.
FX2N-1RM-E-SET Programmable Cam Switch Appendix Memo A-10
USER’S MANUAL FX2N-1RM-E-SET PROGRAMMABLE CAM SWITCH HEAD OFFICE: HIMEJI WORKS: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN 840, CHIYODA CHO, HIMEJI, JAPAN MODEL FX2N1RM-H-E MODEL CODE 09R614 JY992D71101K (MEE) Effective Dec. 2011 Specification are subject to change without notice.
