MITSUBISHI ELECTRIC GOT1000 GT1020/GT1030 to FX Connection Start-up Guide Art.-Nr.
About this Manual The texts, illustrations, diagrams and examples in this manual are only intended as aids to help explain the functioning, operation, use and programming of the GOT1000 terminals in combination with an FX PLC. If you have any questions regarding the installation and operation of the hardware described in this manual, please do not hesitate to contact your sales office or one of your Mitsubishi distribution partners.
II
Table of Contents Table of Contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 Hardware Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.1 GOT Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview 1 Start-up Guide Overview This document provides a simple guide and reference for setting up the GT1020 or GT1030 Graphic Operation Terminal (GOT) hardware and firmware for use with an FX Series PLC. 2 Hardware Introduction The GT1020 and GT1030 are monochrome, 3-color backlight, two communication channel GOT1000 Series touch panel interfaces, and consist of the following models: Model Size Backlight Colors -LBD Green/Orange/Red -LBD2 -LBDW GT1020 -LBDW2 3.
Start-up Guide 3 Cabling Cabling Power All GT1020/GT1030 GOTs except for the GT1020-LBL and GT1020-LBLW (5V DC versions) require an external 24V DC power supply to be connected to the Power Terminal on the back of the GOT. The 5V DC versions are powered through the communication cables, described below. 5V DC version GT1020 GOTs The GT1020-LBL and GT1020-LBLW are the only two 5V DC GOTs in the GOT1000 lineup.
Cabling Start-up Guide Cable Name All RS-232C GT1020/GT1030-to-FX connection cables must be made by the user as described below. Tab. 3: Applicable GOTs FX Comm. Equipment GT1020-LBD2 GT1020-LBDW2 GT1030-LBD2 GT1030-LBDW2 FX3U-232-BD FX3U-232ADP(-MB)햳 FX2N-232-BD FX2NC-232ADP햳 FX1N-232-BD Connection to an RS-232C FX communication channel 햳 Special Adapters require an additional FX**-CNV-BD or, for the FX 3U only, a Communication Expansion Board. GOT Side (terminal block) 3.
Start-up Guide 3.2 Cabling Programming Cables The GT1020 and GT1030 come pre-installed with an OS and FX communication driver, but without any project data. To download a project from a PC running GT Designer2 to the GOT, a programming cable is required that connects to the RS-232C 6-pin Mini-DIN port on the back of the GOT.
Firmware Updates 4 Start-up Guide Firmware Updates (Version 2.73 or later) To make sure the GT1020/GT1030 GOT is able to use the latest functions and features, it is the responsibility of the user to check and update the firmware (Standard monitor OS) of the GOT. Launch the latest copy of GT Designer2 and start a new project for the corresponding GOT model (GT1020 or GT1030) with the “MELSEC-FX” Controller Type. Select “Yes” to set the Communication Setting and make sure the Standard I/F-1 CH No.
Start-up Guide 5 Confirm Communication Confirm Communication The communication monitoring is a function that checks whether the GOT can communicate with the PLC. If no error is shown, communication has been set up correctly.
MITSUBISHI ELECTRIC HEADQUARTERS EUROPEAN REPRESENTATIVES EUROPEAN REPRESENTATIVES MITSUBISHI ELECTRIC EUROPE B.V. EUROPE German Branch Gothaer Straße 8 D-40880 Ratingen Phone: +49 (0)2102 / 486-0 Fax: +49 (0)2102 / 486-1120 MITSUBISHI ELECTRIC EUROPE B.V. CZECH REPUBLIC Czech Branch Radlicka 714/113 a CZ-158 00 Praha 5 Phone: +420 251 551 470 Fax: +420-251-551-471 MITSUBISHI ELECTRIC EUROPE B.V.
