LCD4000 40" LCD Colour Monitor User’s Manual
Index Declaration of conformity ................................................................................................................................ English-1 Important Information ...................................................................................................................................... English-2 Warning, Caution ............................................................................................................................................
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: Address: Tel. No.: NEC-Mitsubishi Electronics Display of America, Inc.
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD4000 LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. Please follow the bylaws or rules of your municipality to dispose of the lamps properly.
Contents Your new LCD4000 LCD monitor box* should contain the following: • LCD4000 LCD monitor • Power Cord (3 m) • PC - Video Signal Cable SC-B113 (4 m) • User’s Manual • Wireless Remote Control and AA Batteries • Clamper x 2 • Screw (M4 x 10) x 2 • CD-ROM • Ferrite Core x 4 • Stand for Independence x 2 • Screw (M5 x 40 mm) for stand x 4 • Band x 3 Ferrite Core x 4 Power Cord PC - Video Signal Cable (D-SUB to D-SUB Cable) Clamper x 2 Screw (M4 x 10) x 2 Stand for the Independenc
English Parts Name and Functions Control Panel buttons 1 POWER button ( ) 7 DOWN ( ) button Switches the power on/off. See also page 19. Activates the OSM menu when the OSM menu is turned-off. Acts as button to move the highlighted area down to select the adjustment with OSM menu. 2 MUTE button Switches the audio mute ON/OFF. 3 INPUT button Acts as SET button with OSM menu. Selects the signal connected with the RGB input connector.
Terminal Panel 1 AC IN connector 6 AUDIO IN 1, 2, 3 Connects with the supplied power cord. To input audio signal from external equipment such as a computer, VCR or DVD player. 2 RGB 1 IN (DVI-D) To input digital RGB signals from a computer having a digital RGB output. 7 AUDIO OUT To output the audio signal from the AUDIO IN 3 jack. * This connector does not support analog input. 8 VIDEO 3 RGB 2 IN (mini D-Sub 15 pin) To input analog RGB signals from a personal computer or other RGB equipment.
5 4 3 6 MUTE button To switch the mute function on/off. 7 VOLUME UP button Increase the audio output level. 8 VOLUME DOWN button 1 Decrease the audio output level. 9 PIP (Picture In Picture) button 2 ON/OFF button: Toggle switches between PIP-ON/ POP-ON/OFF. See page 23. INPUT button: Select the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub picture. 6 9 7 10 8 11 13 10 STILL button ON/OFF button: To switch the still picture mode on/off.
Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. Handling the remote control Use the remote control within a distance of about 7 m from the front of the LCD monitor’s remote control sensor and at a horizontal and vertical angle of within 30° within a distance of about 3 m. * Do not subject to strong shock. * Do not allow water or other liquid to splash the remote control.
1. Determine the installation location 3. Connect external equipment (See pages 12~18) CAUTION: DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF Installing your LCD display must be done by a qualified technician. Contact your dealer for more information. • To protect the connected equipment, turn off the main power before making connections. • Refer to your equipment user manual. 4. Connect the supplied power cord CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE.
How to Mount and Attach Options to the LCD Monitor You can attach mounting accessories to the LCD monitor in one of the following two ways: Ventilation Requirements for enclosure mounting In the upright position To allow heat to disperse, leave space between surrounding objects as shown in the diagram to the right. Ambient temperature should be less than 40°C. * 100mm 100mm 100mm * 100mm * Use some fans as needed.
English How to install stand 1. Please turn monitor off. 2. Insert claws of monitor to stand holes until clicks. 3. Fasten 2 screws (M5 x 40) of both side. Torque 280 ~ 300N cm Screw M5 x 40 Hole of stand Claw of Monitor Stand How to remove the stand 1. Spread the protective sheet on the flat surface, such as a desk. 2. Place monitor on the protective sheet. 3. Remove 2 screws of each stand with a screw driver and keep them for reuse.
Connections Before making connections: * First turn off the power of all equipment to be attached. * Refer to the user manual in regard to this equipment. Wiring Diagram LCD monitor Personal computer DVD player Personal computer HD laser disk player VCR LCD monitor (second monitor) Equipment with digital interface Attaching the Ferrite Core Mounting Position of Ferrite Core Attach the Ferrite Core to PC Audio Cable and S-VIDEO Cable.
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards may not be able to create a correct image resolution. Connect the LCD Monitor to a Personal Computer • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin).
Connecting to a Macintosh® Computer Connecting your Macintosh® computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards or drivers may not display images correctly. Connect the LCD Monitor to Macintosh® • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin).
Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output • The RGB 1 IN connector also accepts a DVI-D cable. • Input TMDS signals conforming to DVI standards. • To maintain display quality, use a cable with a quality prescribed by DVI standards. • The AUDIO IN 1 can be used for audio input. For connection, select AUDIO 1 from the AUDIO INPUT button.
Connecting a VCR Connecting your VCR or laser disc player to your LCD monitor will enable you to display your VCR’s or laser disc player’s video. Refer to your VCR or laser disc player owner’s manual for more information. Connect the LCD Monitor to a VCR or Laser Disc Player • Video signals can be connected to either the VIDEO IN [RCA or BNC] or the S-VIDEO IN connector. NOTE: S-VIDEO is priority input. Only one of the connectors, either RCA or BNC, can be used alternatively.
English Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user’s manual for more information. Connect the LCD Monitor to a DVD Player To connect the RGB 3 DVD/HD In connector (BNC) on the LCD monitor, use a separately available BNC connector cable. You will need a separately available BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable.
Connecting a Stereo Amplifier You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier user’s manual for more information. Connect the LCD Monitor to a Stereo Amplifier • Turn on the LCD monitor and the amplifier only after all connections have been made. • Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. • Do not reverse the audio left and right jacks. • The AUDIO IN is used for audio input.
English Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on, or red when in off mode. The monitor can be powered on or off using the following three options: 1. Pressing the power button. Note: Before operating the remote control, be sure to turn on the Main Power Switch on LCD monitor. Power Switch 2. Using the remote control. Note: Before operating the remote control, be sure to turn on the Main Power Switch on the LCD monitor.
Power Indicator Information OSM RGB1, 2, 3 Power ON Status Green Power OFF Red Power Standby Red and Green RGB2 1024 x 768 ) 48kHz 60Hz AUDIO : 1 SCREEN SIZE : FULL Using Power Management The LCD monitor follows the VESA approved DPMS Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keybord or the mouse has not been used for a fixed period.
Press UP or DOWN button to select sub-menu SET Remote Control Press SET button to decide Press UP or DOWN, and PLUS or MINUS button to select function, or control which you like Press MENU or EXIT button to decide MENU SET SET SET EXIT Press UP or DOWN button to select Press INPUT button to decide Press UP or DOWN button to select Press INPUT button to decide INPUT INPUT Control Panel UP or DOWN button INPUT button BRIGHTNESS BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL COLOR CONTROL COLOR T
COLOR TEMPERATURE BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET COLOR TEMPERATURE L :SEL :SEL EXIT:PRE SET:NEXT MENU:END PICTURE RESET H EXIT:PRE MENU:END Selecting Picture reset allows you to reset all OSM settings related to PICTURE. PICTURE RESET BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL COLOR CONTROL COLOR TEMPERATURE PICTURE RESET To adjust the colour temperature of entire screen.
PICTURE SCREEN AUDIO PICTURE IN PICTURE CONFIGURATION 1 CONFIGURATION 2 AUDIO Sub-Menu :SEL EXIT:PRE SET:NEXT MENU:END To accentuate or reduce the high frequency sound. TREBLE BASS AUDIO RESET TREBLE TREBLE - + :SEL :SEL EXIT:PRE SET:NEXT MENU:END EXIT:PRE Press + button to increase TREBLE sound. Press - button to decrease TREBLE sound. MENU:END To accentuate or reduce the low frequency sound.
POWER SAVE Selecting the power management ON/OFF mode.
English OSM (On-Screen-Manager) Controls - DVD&HD Input Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION PICTURE Sub-Menu BRIGHTNESS :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS COLOR BLACK LEVEL PICTURE RESET 50 - :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS COLOR BLACK LEVEL PICTURE RESET CONTRAST SHARPNESS + :SEL EXIT:PRE MENU:END 50 - + :SEL EXIT:PRE MENU:END SHARPNESS 50 - :SEL EXIT:PRE SET:NEXT MENU:END Press + button to increase brigh
Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION PICTURE IN PICTURE Sub-Menu :SEL EXIT:PRE SET:NEXT MENU:END Selecting the size of picture inserted at the “Picture-in Picture” (PIP) mode. “Large”, “Middle”, and “Small” are available. PIP SIZE PIP SIZE PIP AUDIO PIP RESET PIP SIZE LARGE MIDDLE SMALL :SEL EXIT:PRE SET:NEXT MENU:END :SEL EXIT:PRE MENU:END Selecting the sound source in PIP mode.
English OSM (On-Screen-Manager) Controls - AV Input Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION PICTURE Sub-Menu BRIGHTNESS :SEL EXIT:PRE SET:NEXT MENU:END BRIGHTNESS CONTRAST SHARPNESS TINT COLOR BLACK LEVEL NOISE REDUCTION PICTURE RESET 50 - + :SEL :SEL EXIT:PRE SET:NEXT MENU:END CONTRAST BRIGHTNESS CONTRAST SHARPNESS TINT COLOR BLACK LEVEL NOISE REDUCTION PICTURE RESET SHARPNESS EXIT:PRE MENU:END 50 - Press + button to increase brightness.
Main-Menu PICTURE AUDIO PICTURE IN PICTURE CONFIGURATION AUDIO Sub-Menu :SEL EXIT:PRE SET:NEXT MENU:END TREBLE BASS AUDIO RESET TREBLE To accentuate or quiet the high frequency sound. TREBLE - + :SEL :SEL EXIT:PRE SET:NEXT MENU:END EXIT:PRE Press + button to increase TREBLE sound. Press - button to decrease TREBLE sound. MENU:END To accentuate or quiet the low frequency sound.
OFF TIMER :SEL EXIT:PRE SET:NEXT MENU:END SCREEN SAVER LANGUAGE OSM TIME OFF TIMER SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END COLOR SYSTEM LANGUAGE OSM TIME OFF TIMER SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END CONFIGURATION RESET LANGUAGE OSM TIME OFF TIMER SCREEN SAVER COLOR SYSTEM CONFIGURATION RESET :SEL EXIT:PRE SET:NEXT MENU:END OFF TIMER ON OFF :SEL 24H EXIT:PRE MENU:END In the OFF TIMER menu, you can select monitor
Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be remote controlled by connecting a computer with RS-232C interface. The following functions can be controlled by a computer: • Turn the monitor ON or OFF. • Changing input signals. Connection LCD Monitor + IBM PC or IBM PC compatible to RS-232C terminal PC or IBM compatible RS-232C Cable NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required.
(1) The command from a computer to the LCD monitor will be sent within 400ms. (2) The LCD monitor will send a return command 400ms* after it has received and executed a code. If the command isn’t received correctly, the LCD monitor will not send the return command. (3) The computer checks the command and confirms if the command which has been sent has been executed or not. (4) The LCD monitor sends various codes other than the return code.
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another. Colour Control Systems: Six colour presets select the desired colour setting (sRGB and NATIVE colour presets are standard and cannot be changed). Colour temperature increases or decreases, in each preset.
No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recommended settings.
Specifications for LCD4000 Product Specifications Analog Input LCD Module Pixel Pitch: Resolution: Colour: Brightness: Viewing Angle: External speaker out put inpedance Frequency Digital Input (40" / 101.6cm diagonal) 0.681mm 1280 x 768 dots (WXGA) 16,777,216 450cd/m2 (Typ.) Up 85°/ Down 85°/ Left 85°/ Right 85° (typ) @ CR>10 Rating 7W x 7W (8Ohm) Horizontal: 31.5kHz - 75.0kHz (15.75/15.625kHz) Vertical: 58.0 - 62.0 Hz 58.0 - 62.0 Hz Pixel Clock 25.0MHz - 162.0MHz Viewable Size 871.68 x 523.
English Pin Assignment 1) Analog RGB input (MiniDsub15p): R G B 2 Pin No Name 1 Video Signal Red 2 Video Signal Green 3 Video Signal Blue 4 GND 5 DDC-GND 6 Red-GND 7 Green-GND 8 Blue-GND 9 NC 10 SYNC-GND 11 GND 12 DDC-SDA 13 H-SYNC 14 V-SYNC 15 DDC-SCL Mini D-SUB 15P 1 5 6 10 11 15 2) S-VIDEO input: V I D E O Pin No Name 1 GND 2 GND 3 Y (Luminance) 4 C (Chroma) 3) Digital RGB input (DVI-D): R G B 1 Pin - Assignment of DVI connector: 1 8 TX2- 9 TX1- 17 T
