Specifications

BODY TYPE
Engine
Model
Type
No. of cylinders
Bore x stroke
Piston displacement
Max. output (JIS)
Max. torque (JIS)
Alternator
Air cleaner
Clutch
Facing material, diameter
Transmission
Model
Type
Gear ratios
Front Axle
Rear Axle
Final reduction gear
Model
Ratio
Tires and Disc Wheels
Tire size
Tread pattern
Disc wheel size
Steering
Suspensions
span x width x thickness
Front
–No. of leaves
Rear
1
span x width x thickness
Main
–No. of leaves
1
Helper
Brakes
Service
Parking
Exhaust System
Tail pipe
Frame
Electrical System
Battery
Fuel Tank
Paint
Wooden cargo
MITSUBISHI FUSO 4M40-0A
4 stroke-cycle, water-cooled diesel engine with swirl chamber
4 in line
95 mm x 100 mm (3.74 in. x 3.94 in.)
2.835 L (173.1 cu.in.)
69 kW (94 PS) / 4,000 rpm
191 N·m (19.5 kgf·m, 141 lb·ft) / 2,000 rpm
12 Volt, AC, 75 Amp.
Dry paper element type with snorkel
Hydraulic control, diaphragm spring, single dry plate
Woven (asbestos free), 260 mm (10.2 in.)
M015S5
5 forward and 1 reverse speed,
1st to 5th synchromesh, Rev. constantmesh gears
4.733-2.753-1.490-1.000-0.839, Rev. 4.733
Reverse Elliot, "Ι" beam
Full floating type
Single reduction, hypoid gear
D1H
5.285
Single front, single rear
7.00-15-6PR front, 7.00-15-10PR rear
Rib
15 x 5.50F-25-4.5t, 6 studs, 2 pieces
Ball-nut type. Telescopic and tilt steering column with steering lock
Semi-elliptic, laminated leaf springs
1,200 mm x 70 mm x
9 mm-2 (
47.2 in. x 2.76 in. x
0.35 in.)
10 mm-2 0.39 in.)
Semi-elliptic, laminated leaf springs
1,200 mm x 70 mm x
11 mm-2 (
47.2 in. x 2.76 in. x
0.43 in.)
18 mm-1 0.71 in.)
95 mm x 65 mm x 85 mm (3.74 in. x 2.56 in. x 3.35 in.) (Rubber)
Hydraulic with vacuum servo assistance, dual circuit
Internal expanding type on propeller shaft at rear of transmission
Conventional (horizontal) type muffler
Drop tail type, blowing to chassis rearward
Parallel, tapered channel section with reinforcement and crossmembers
12 Volt, regulated control
12 Volt x 1, 110 Ah (396 kC) at 20 hr rate (115E41L)
88 Ah (317 kC) at 5 hr rate (115E41L)
70 lits. (dm
3
) (15.4 lmp.gals. or 18.5 U.S.gals.)
Finish coat, Natural White
Spec. No. FB71-C, 2/2
FB71A SERIES CARGO BODY SPECIFICATIONS
FB71A SERIES CHASSIS SPECIFICATIONS
Floor
Cross sill height x width
Floor board thickness
Floor frame
Guard Frame
Outside post thickness
Upper rail thickness
Horizontal rail thickness
Vertical pillar thickness
Header panel thickness
Side & Rear Gate
Top rail thickness
Side post thickness
Bottom rail thickness
Board & panel thickness
Accessories
Rope hook diameter
Rear fender thickness
Side gate support
Plywood
Plywood
Form-rolled steel
Form-rolled steel
Bended steel
Bended steel
Bended steel
Plywood
Form-rolled steel
Pressed steel
Form-rolled steel
Plywood overlaid with steel metal
Steel rod
Plastic (P.P.)
1 pair
72 mm x 40 mm or 35 mm (2.83 in. x 1.57 in. or 1.38 in.)
14 mm (0.55 in.)
2.3 mm (0.09 in.)
2.3 mm (0.09 in.)
2.3 mm (0.09 in.)
2.3 mm (0.09 in.)
1.4 mm (0.06 in.)
11 mm (0.43 in.)
1.8 mm (0.07 in.)
1.6 mm (0.06 in.)
1.6 mm (0.06 in.)
11.3 mm (0.44 in.)
12.7 mmφ (Dia. 0.50 in.)
3.0 mm (0.12 in.)
(
)
ANNOTATION
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
(
)