Specifications

Engine
Model
Type
No. of cylinders
Bore x stroke
Piston displacement
Max. output (JIS)
Max. torque (JIS)
Alternator
Air cleaner
Clutch
Facing material, diameter
Transmission
Model
Type
Gear ratios
Front Axle
Rear Axle
Final reduction gear
Model
Ratio
Tires and Disc Wheels
Tire size
Tread pattern
Disc wheel size
Steering
Suspensions
span x width x thickness
Front
–No. of leaves
Rear
span x width x thickness
Main
–No. of leaves
Helper
Brakes
Service
Parking
Exhaust System
Tail pipe
Frame
Electrical System
Batteries
Fuel Tank
Paint
MITSUBISHI FUSO 4D34-3A
4 stroke-cycle, water-cooled direct injection diesel engine
4 in line
104 mm x 115 mm (4.09 in. x 4.53 in.)
3.907 L (238.4 cu.in.)
80 kW (109 PS) / 3,200 rpm
255 N·m (26.0 kgf·m, 188 lb·ft) / 1,800 rpm
24 Volt, AC, 50 Amp.
Dry paper element type with snorkel
Hydraulic control, diaphragm spring, single dry plate
Woven (asbestos free), 275 mm (10.8 in.)
M025S5
5 forward and 1 reverse speed,
1st to 5th synchromesh, Rev. constantmesh gears
5.181-2.865-1.593-1.000-0.739, Rev. 5.181
Reverse Elliot,
"Ι"
beam
Full floating type
Single reduction, hypoid gear
D2H
6.166
Single front, dual rear
7.00-16-10PR
Rib
16 x 5.50F-115-8t, 5 studs, 2 pieces
Ball-nut type. Telescopic and tilt steering column with steering lock
Semi-elliptic, laminated leaf springs
Hydraulic with vacuum servo assistance, dual circuit
Internal expanding type on propeller shaft at rear of transmission
Conventional (horizontal) type muffler
Drop tail type, blowing to chassis rearward
Parallel, tapered channel section with reinforcement and crossmembers
24 Volt, regulated control
12 Volt x 2, 65 Ah (234 kC) at 20 hr rate (75D26L)
52 Ah (187 kC) at 5 hr rate (75D26L)
70 lits. (dm
3
) (15.4 lmp.gals. or 18.5 U.S.gals.) 100 lits. (dm
3
) (22.0 lmp.gals. or 26.4 U.S.gals.)
Finish coat, Natural White
BODY TYPE
Floor
Main sill height x width x thickness
Cross sill height x width
Floor board thickness
Floor frame
Guard Frame
Outside post thickness
Upper rail thickness
Horizontal rail thickness
Vertical pillar thickness
Header panel thickness
Side & Rear Gate
Top rail thickness
Side post thickness
Bottom rail thickness
Board & panel thickness
Accessories
Rope hook diameter
Rear fender thickness
Side gate support
Wooden cargo
Steel pipe 90 mm x 40 mm x 2.3 mm (3.54 in. x 1.57 in. x 0.09 in.)
Plywood 93 mm x 40 mm or 35 mm (3.66 in. x 1.57 in. or 1.38 in.)
Plywood 14 mm(0.55 in.)
Form-rolled steel 2.3 mm(0.09 in.)
Pressed steel 3.2 mm (0.13 in.)
Bended steel 3.2 mm (0.13 in.)
Bended steel 2.3 mm (0.09 in.)
Bended steel 1.4 mm (0.06 in.)
Plywood 11 mm (0.43 in.)
Form-rolled steel 2.0 mm (0.08 in.)
Pressed steel 1.6 mm (0.06 in.)
Form-rolled steel 1.6 mm (0.06 in.)
Plywood overlaid with steel metal 13.3 mm (0.52 in.)
Steel rod 12.7 mmφ (Dia. 0.50 in.)
Plastic (P.P.) 3.0 mm(0.12 in.)
1 pair
FE73PB6 FE73PE6
Spec. No. FE73-C, 2/2
FE73P SERIES CARGO BODY SPECIFICATIONS
FE73P SERIES CHASSIS SPECIFICATIONS
ANNOTATION
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
Semi-elliptic, laminated leaf springs
1,200 mm x 70 mm x 10 mm-5 (47.2 in. x 2.76 in. x 0.39 in.)
990 mm x 70 mm x 8 mm-4 (39.0 in. x 2.76 in. x 0.31 in.)
1,250 mm
x
70 mm
x
11 mm-4
49.2 in. x 2.76 in. x
0.43 in.)
10 mm-1 0.39 in.
(
)