Specifications

Engine
Model
Type
No. of cylinders
Bore x stroke
Piston displacement
Max. output (JIS)
Max. torque (JIS)
Alternator
Air cleaner
Clutch
Facing material
Transmission
Model
Type
Gear ratios
Front Axle
Rear Axle
Final reduction gear
Model
Ratio
Tires and Disc Wheels
Tire size
Tread pattern
Disc wheel size
Steering
Suspensions
span x width x thickness
Front
–No. of leaves
Rear
span x width x thickness
Main
–No. of leaves
Helper
Brakes
Service
Parking
Exhaust System
Tail pipe
Frame
Electrical System
Batteries
Fuel Tank
Paint
MITSUBISHI FUSO 4D34-3A
4 stroke-cycle, water-cooled direct injection diesel engine
4 in line
104 mm x 115 mm (4.09 in. x 4.53 in.)
3.907L (238.4 cu.in.)
80 kW (109 PS) / 3,200 rpm
255 N
· m (26.0 kgf · m / 188 lb · ft)
24 Volt, AC, 50 Amp.
Dry paper element type with snorkel
Hydraulic control, diaphragm spring, single dry plate
Woven (asbestos free), 275 mm (10.8 in.)
M025S5
5 forward and 1 reverse speed,
1st to 5th synchromesh, Rev. constantmesh gears
5.181-2.865-1.593-1.000-0.739, Rev. 5.181
Reverse Elliot,
"Ι"
beam
Full floating type
Single reduction, hypoid gear
D2H
6.166
Single front, dual rear
6.50-16-10PR
Lug
16 x 5.50F-115-8t, 5 studs, 2 pieces
Ball-nut type. Telescopic and tilt steering column with steering lock
Semi-elliptic, laminated leaf springs
1,200 mm x 70 mm x
10 mm-1 (
47.2 in. x 2.76 in. x
0.39 in.)
11 mm-3 0.43 in.
Semi-elliptic, laminated leaf springs
12 mm-3 0.47 in.
1,250 mm x 70 mm x 20 mm-1 49.2 in. x 2.76 in. x 0.79 in.
18 mm-1 0.71 in.
120 mm x 68 mm x 122 mm (4.72 in. x 2.68 in. x 4.8 in.) (Rubber)
Hydraulic with vacuum servo assistance, dual circuit
Internal expanding type on propeller shaft at rear of transmission
Conventional (horizontal) type muffler
Drop tail type, blowing to chassis rearward
Parallel, tapered channel section with reinforcement and crossmembers
24 Volt, regulated control
12 Volt x 2, 65 Ah (234 kC) at 20 hr rate (75D26L)
52 Ah (187 kC) at 5 hr rate (75D26L)
70 lits. (dm
3
) (15.4 lmp.gals. or 18.5 U.S.gals.)
Finish coat, Natural White
Spec. No. FE71-D, 2/2
FE71PBD4 SERIES DUMP BODY SPECIFICATIONS
FE71PBD4 SERIES CHASSIS SPECIFICATIONS
BODY TYPE
Body
Floor thickness
Front panel thickness
Side panel thickness
Tail panel thickness
Type of Tipping Gear
Pump
Type
Capacity
Hoist
Type
Bore x stroke
Tipping Performance
Angle of tip (approx.)
Lifting time (approx.)
Lowering time (approx.)
Drop side & tail
3.2 mm (0.13 in.)
2.3 mm (0.09 in.)
3.2 mm (0.13 in.)
3.2 mm (0.13 in.)
Under body, hydraulic cylinder with link mechanism
Gear type (KPC-25)
24.8 cc/rev (1.52 cu.in./rev)
Single piston type with link
130 mm x 422 mm (5.1 in. x 16.6 in.)
60 degree
20 sec.
20 sec.
ANNOTATION
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
()
()